scholarly journals Simulation of Producer Gas Fired Power Plants with Inlet Fog Cooling and Steam Injection

2006 ◽  
Vol 129 (3) ◽  
pp. 637-647 ◽  
Author(s):  
Mun Roy Yap ◽  
Ting Wang
Keyword(s):  
Natural Gas ◽  
Steam Turbine ◽  
Gas Turbine ◽  
Power Output ◽  
Power Plants ◽  
Steam Injection ◽  
Combined Cycle ◽  
Producer Gas ◽  
Turbine Inlet ◽  
Cycle Systems

Biomass can be converted to energy via direct combustion or thermochemical conversion to liquid or gas fuels. This study focuses on burning producer gases derived from gasifying biomass wastes to produce power. Since the producer gases are usually of low calorific values (LCV), power plant performance under various operating conditions has not yet been proven. In this study, system performance calculations are conducted for 5MWe power plants. The power plants considered include simple gas turbine systems, steam turbine systems, combined cycle systems, and steam injection gas turbine systems using the producer gas with low calorific values at approximately 30% and 15% of the natural gas heating value (on a mass basis). The LCV fuels are shown to impose high compressor back pressure and produce increased power output due to increased fuel flow. Turbine nozzle throat area is adjusted to accommodate additional fuel flows to allow the compressor to operate within safety margin. The best performance occurs when the designed pressure ratio is maintained by widening nozzle openings, even though the turbine inlet pressure is reduced under this adjustment. Power augmentations under four different ambient conditions are calculated by employing gas turbine inlet fog cooling. Comparison between inlet fog cooling and steam injection using the same amount of water mass flow indicates that steam injection is less effective than inlet fog cooling in augmenting power output. Maximizing steam injection, at the expense of supplying the steam to the steam turbine, significantly reduces both the efficiency and the output power of the combined cycle. This study indicates that the performance of gas turbine and combined cycle systems fueled by the LCV fuels could be very different from the familiar behavior of natural gas fired systems. Care must be taken if on-shelf gas turbines are modified to burn LCV fuels.

Simulation of Producer Gas Fired Power Plants With Inlet Fog Cooling and Steam Injection

2006 ◽  
Author(s):  
Mun Roy Yap ◽  
Ting Wang
Keyword(s):  
Natural Gas ◽  
Steam Turbine ◽  
Gas Turbine ◽  
Power Output ◽  
Gas Turbines ◽  
Power Plants ◽  
Steam Injection ◽  
Combined Cycle ◽  
Producer Gas ◽  
Cycle Systems

Biomass can be converted to energy via direct combustion or thermo-chemical conversion to liquid or gas fuels. This study focuses on burning producer gases derived from gasifying biomass wastes to produce power. Since the producer gases are usually low calorific values (LCV), the power plants performance under various operating conditions has not yet been proven. In this study, system performance calculations are conducted for 5MWe power plants. The power plants considered include simple gas turbine systems, steam turbine systems, combined cycle systems, and steam injection gas turbine systems (STIG) using the producer gas with low calorific values at approximately 30% and 15% of the natural gas heating value (on a mass basis). The LCV fuels are shown to impose high back compressor pressure and produces increased power output due to increased fuel flow. Turbine nozzle throat area is adjusted to accommodate additional fuel flows to allow compressor operate within safety margin. The best performance occurs when the designed pressure ratio is maintained by widening nozzle openings, even though the TIT is reduced under this adjustment. Power augmentations under four different ambient conditions are calculated by employing gas turbine inlet fog cooling. Comparison between inlet fog cooling and steam injection using the same amount of water mass flow indicates that steam injection is less effective than inlet fog cooling in augmenting power output. Maximizing steam injection, at the expense of supplying the steam to the steam turbine, significantly reduces both the efficiency and the output power of the combined cycle. This study indicates that the performance of gas turbine and combined cycle systems fueled by the LCV fuels could be very different from the familiar behavior of natural gas fired systems. Care must be taken if on-shelf gas turbines are modified to burn LCV fuels.

Effects of Steam Reheat in Advanced Steam Injected Gas Turbine Cycles

1998 ◽  
Author(s):  
A. Hofstädter ◽  
H. U. Frutschi ◽  
H. Haselbacher
Keyword(s):  
Steam Turbine ◽  
Gas Turbine ◽  
Power Plants ◽  
Steam Injection ◽  
Combined Cycle ◽  
Back Pressure ◽  
Turbine Efficiency ◽  
Pressure Steam ◽  
Additional Improvement ◽  
Gas Turbine Exhaust

Steam injection is a well-known principle for increasing gas turbine efficiency by taking advantage of the relatively high gas turbine exhaust temperatures. Unfortunately, performance is not sufficiently improved compared with alternative bottoming cycles. However, previously investigated supplements to the STIG-principle — such as sequential combustion and consideration of a back pressure steam turbine — led to a remarkable increase in efficiency. The cycle presented in this paper includes a further improvement: The steam, which exits from the back pressure steam turbine at a rather low temperature, is no longer led directly into the combustion chamber. Instead, it reenters the boiler to be further superheated. This modification yields additional improvement of the thermal efficiency due to a significant reduction of fuel consumption. Taking into account the simpler design compared with combined-cycle power plants, the described type of an advanced STIG-cycle (A-STIG) could represent an interesting alternative regarding peak and medium load power plants.

Repowering: An Option for Refurbishment of Old Thermal Power Plants in Latin-American Countries

2010 ◽  
Author(s):  
Washington Orlando Irrazabal Bohorquez ◽  
Joa˜o Roberto Barbosa ◽  
Luiz Augusto Horta Nogueira ◽  
Electo E. Silva Lora
Keyword(s):  
Power Plant ◽  
Natural Gas ◽  
Steam Turbine ◽  
Gas Turbine ◽  
Power Plants ◽  
Thermal Power ◽  
Rankine Cycle ◽  
Combined Cycle ◽  
Fuel Oil ◽  
Thermal Power Plants

The operational rules for the electricity markets in Latin America are changing at the same time that the electricity power plants are being subjected to stronger environmental restrictions, fierce competition and free market rules. This is forcing the conventional power plants owners to evaluate the operation of their power plants. Those thermal power plants were built between the 1960’s and the 1990’s. They are old and inefficient, therefore generating expensive electricity and polluting the environment. This study presents the repowering of thermal power plants based on the analysis of three basic concepts: the thermal configuration of the different technological solutions, the costs of the generated electricity and the environmental impact produced by the decrease of the pollutants generated during the electricity production. The case study for the present paper is an Ecuadorian 73 MWe power output steam power plant erected at the end of the 1970’s and has been operating continuously for over 30 years. Six repowering options are studied, focusing the increase of the installed capacity and thermal efficiency on the baseline case. Numerical simulations the seven thermal power plants are evaluated as follows: A. Modified Rankine cycle (73 MWe) with superheating and regeneration, one conventional boiler burning fuel oil and one old steam turbine. B. Fully-fired combined cycle (240 MWe) with two gas turbines burning natural gas, one recuperative boiler and one old steam turbine. C. Fully-fired combined cycle (235 MWe) with one gas turbine burning natural gas, one recuperative boiler and one old steam turbine. D. Fully-fired combined cycle (242 MWe) with one gas turbine burning natural gas, one recuperative boiler and one old steam turbine. The gas turbine has water injection in the combustion chamber. E. Fully-fired combined cycle (242 MWe) with one gas turbine burning natural gas, one recuperative boiler with supplementary burners and one old steam turbine. The gas turbine has steam injection in the combustion chamber. F. Hybrid combined cycle (235 MWe) with one gas turbine burning natural gas, one recuperative boiler with supplementary burners, one old steam boiler burning natural gas and one old steam turbine. G. Hybrid combined cycle (235 MWe) with one gas turbine burning diesel fuel, one recuperative boiler with supplementary burners, one old steam boiler burning fuel oil and one old steam turbine. All the repowering models show higher efficiency when compared with the Rankine cycle [2, 5]. The thermal cycle efficiency is improved from 28% to 50%. The generated electricity costs are reduced to about 50% when the old power plant is converted to a combined cycle one. When a Rankine cycle power plant burning fuel oil is modified to combined cycle burning natural gas, the CO2 specific emissions by kWh are reduced by about 40%. It is concluded that upgrading older thermal power plants is often a cost-effective method for increasing the power output, improving efficiency and reducing emissions [2, 7].

Optimum Performance Improvements of the Combined Cycle Based on an Intercooler–Reheated Gas Turbine

2015 ◽  
Vol 137 (6) ◽  
Author(s):  
Thamir K. Ibrahim ◽  
M. M. Rahman
Keyword(s):  
Gas Turbine ◽  
Power Output ◽  
Thermal Efficiency ◽  
Power Plants ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Optimum Level ◽  
Simulation Code ◽  
Operation Conditions ◽  
Turbine Inlet

The performance enhancements and modeling of the gas turbine (GT), together with the combined cycle gas turbine (CCGT) power plant, are described in this study. The thermal analysis has proposed intercooler–reheated-GT (IHGT) configuration of the CCGT system, as well as the development of a simulation code and integrated model for exploiting the CCGT power plants performance, using the matlab code. The validation of a heavy-duty CCGT power plants performance is done through real power plants, namely, MARAFIQ CCGT plants in Saudi Arabia with satisfactory results. The results from this simulation show that the higher thermal efficiency of 56% MW, while high power output of 1640 MW, occurred in IHGT combined cycle plants (IHGTCC), having an optimal turbine inlet temperature about 1900 K. Furthermore, the CCGT system proposed in the study has improved power output by 94%. The results of optimization show that the IHGTCC has optimum power of 1860 MW and thermal efficiency of 59%. Therefore, the ambient temperatures and operation conditions of the CCGT strongly affect their performance. The optimum level of power and efficiency is seen at high turbine inlet temperatures and isentropic turbine efficiency. Thus, it can be understood that the models developed in this study are useful tools for estimating the CCGT power plant's performance.

scholarly journals The Gas Turbine GT26 in Combined Cycle Application: Conversion of a Coal Power Plant Into a Modern Combined Cycle Firing Natural Gas and Oil No. 2

1996 ◽  
Author(s):  
Viktor Scherer ◽  
Dieter Scherer
Keyword(s):  
Power Plant ◽  
Natural Gas ◽  
Steam Turbine ◽  
Gas Turbine ◽  
Steam Generator ◽  
Power Output ◽  
Combined Cycle ◽  
Public Utility ◽  
Total Output ◽  
Hard Coal

The current paper describes the repowering of an existing coal plant (Rheinhafen Power Station). In this power plant, the hard coat boiler was repleced by a modern once through, Heat Recovery Steam Generator (HRSG). The HRSG is connected to a natural gas or oil fired gas turbine ABB GT26. The plant is located in Karlsruhe, Germany, and is operated by the Badenwerk AG, a public utility. The original hard coal fired plant was put into service in 1964. It is equipped with a steam turbine of approx. 100 MW power output. To maintain the initial steam data of the power plant at 160 bar and 540 °C, and to guarantee a low start-up time, an unfired once through type steam generator was chosen. Minor modifications were done in the steam turbine to increase the maximum steam turbine power output to approx. 124 MW. Combined with the approx. 240 MW power output of the GT26 a total output of 363.5 MW. MW is expected. The efficiency has thus been increased from 38 % for the steam power plant to 58.2% for the combined cycle.

Genetic Optimization of Steam Injected Gas Turbine Power Plants

2002 ◽  
Author(s):  
Ibrahim Sinan Akmandor ◽  
O¨zhan O¨ksu¨z ◽  
Sec¸kin Go¨kaltun ◽  
Melih Han Bilgin
Keyword(s):  
Gas Turbine ◽  
Power Output ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Power Plants ◽  
Pressure Ratio ◽  
Steam Injection ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Compressor Pressure Ratio

A new methodology is developed to find the optimal steam injection levels in simple and combined cycle gas turbine power plants. When steam injection process is being applied to simple cycle gas turbines, it is shown to offer many benefits, including increased power output and efficiency as well as reduced exhaust emissions. For combined cycle power plants, steam injection in the gas turbine, significantly decreases the amount of flow and energy through the steam turbine and the overall power output of the combined cycle is decreased. This study focuses on finding the maximum power output and efficiency of steam injected simple and combined cycle gas turbines. For that purpose, the thermodynamic cycle analysis and a genetic algorithm are linked within an automated design loop. The multi-parameter objective function is either based on the power output or on the overall thermal efficiency. NOx levels have also been taken into account in a third objective function denoted as steam injection effectiveness. The calculations are done for a wide range of parameters such as compressor pressure ratio, turbine inlet temperature, air and steam mass flow rates. Firstly, 6 widely used simple and combined cycle power plants performance are used as test cases for thermodynamic cycle validation. Secondly, gas turbine main parameters are modified to yield the maximum generator power and thermal efficiency. Finally, the effects of uniform crossover, creep mutation, different random number seeds, population size and the number of children per pair of parents on the performance of the genetic algorithm are studied. Parametric analyses show that application of high turbine inlet temperature, high air mass flow rate and no steam injection lead to high power and high combined cycle thermal efficiency. On the contrary, when NOx reduction is desired, steam injection is necessary. For simple cycle, almost full amount of steam injection is required to increase power and efficiency as well as to reduce NOx. Moreover, it is found that the compressor pressure ratio for high power output is significantly lower than the compressor pressure ratio that drives the high thermal efficiency.

scholarly journals USE OF GAS TURBINES FOR COMBINED ENERGY PRODUCTION

2020 ◽  
Vol 47 (1) ◽  
pp. 8-18
Author(s):  
V. A. Bulanin
Keyword(s):  
Natural Gas ◽  
Steam Turbine ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Ad Hoc ◽  
Combined Cycle ◽  
New Energy ◽  
State Of Research ◽  
Cis Countries

Abstract. Aim. Despite the obvious expediency of their widespread implementation, gas turbine (GT) and combined cycle gas turbine (CCGT) plants were only used in limited quantities in the former USSR and CIS countries. Due to the exhaustion of possibilities to increase the fuel use efficiency and return on investment (ROI) in steam-turbine combined heat and power (CHP) plants, the development of GT and CCGT plants becomes an urgent problem. In current global practice, the primary fuel for gas turbines and combined cycle gas turbines is natural gas. However, until recently, there has been a lack of experience in the design, construction and operation of GT and CCGT plants in the CIS countries. Method. Due to the ad hoc nature of research in this area, it was necessary to systematise the results of existing studies and assess the state of research at the world level taking regional characteristics into account. Results. The article presents the main considerations and potential effectiveness of the use of gas turbines. Basic gas turbine construction schemes are investigated along with their techno-economic characteristics and an assessment of their comparative utility. Conclusion. Considering the widespread availability of natural gas, it is recommended that gas turbine and combined-cycle plants be installed as part of the process of technical re-equipment in the fuel and energy complex, industry, agriculture and municipal energy sectors as part of the design and construction of new energy sources in the light of positive world experience and the current level of development of gas turbine technologies. Ubiquitous implementation of gas turbine units in the centres supplying heat and electric loads will reduce the regional economy’s need for energy fuel and ensure an increase in energy capacity without the need to construct new complex and uneconomic steam turbine power plants. 

Performance Entitlement of Supercritical Steam Bottoming Cycle

2013 ◽  
Vol 135 (12) ◽  
Author(s):  
S. Can Gülen
Keyword(s):  
Steam Turbine ◽  
Gas Turbine ◽  
Power Plants ◽  
Performance Enhancement ◽  
Combined Cycle ◽  
Cycle Systems ◽  
Steam Boilers ◽  
Potential Impact ◽  
Gas Turbine Exhaust ◽  
Turbine Exhaust

A supercritical steam bottoming cycle has been proposed as a performance enhancement option for gas turbine combined cycle power plants. The technology has been widely used in coal-fired steam turbine power plants since the 1950s and can be considered a mature technology. Its application to the gas-fired combined cycle systems presents unique design challenges due to the much lower gas temperatures (i.e., 650 °C at the gas turbine exhaust vis-à-vis 2000 °C in fossil fuel-fired steam boilers). Thus, the potential impact of the supercritical steam conditions is hampered to the point of economic infeasibility. This technical brief draws upon the second-law based exergy concept to rigorously quantify the performance entitlement of a supercritical high-pressure boiler section in a heat recovery steam generator utilizing the exhaust of a gas turbine to generate steam for power generation in a steam turbine.

Natural Gas Decarbonization to Reduce CO2 Emission From Combined Cycles—Part II: Steam-Methane Reforming

2000 ◽  
Vol 124 (1) ◽  
pp. 89-95 ◽  
Author(s):  
G. Lozza ◽  
P. Chiesa
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Partial Oxidation ◽  
Power Plants ◽  
Combined Cycle ◽  
Performance Estimation ◽  
Thermodynamic Efficiency ◽  
Methane Reforming ◽  
Operating Pressure ◽  
Carbon Conversion

This paper discusses novel schemes of combined cycle, where natural gas is chemically treated to remove carbon, rather than being directly used as fuel. Carbon conversion to CO2 is achieved before gas turbine combustion. The first part of the paper discussed plant configurations based on natural gas partial oxidation to produce carbon monoxide, converted to carbon dioxide by shift reaction and therefore separated from the fuel gas. The second part will address methane reforming as a starting reaction to achieve the same goal. Plant configuration and performance differs from the previous case because reforming is endothermic and requires high temperature heat and low operating pressure to obtain an elevated carbon conversion. The performance estimation shows that the reformer configuration has a lower efficiency and power output than the systems addressed in Part I. To improve the results, a reheat gas turbine can be used, with different characteristics from commercial machines. The thermodynamic efficiency of the systems of the two papers is compared by an exergetic analysis. The economic performance of natural gas fired power plants including CO2 sequestration is therefore addressed, finding a superiority of the partial oxidation system with chemical absorption. The additional cost of the kWh, due to the ability of CO2 capturing, can be estimated at about 13–14 mill$/kWh.

Sign in / Sign up

Export Citation Format

Share Document