Development of a simulation model of energy-saving system based on CCGT-110 and ABСM for energy and thermodynamic analysis

Objectives. Simulation modeling is increasingly being used for the study of complex economic, technical, biological, etc. systems. Such systems are characterized by multifactorial relationships of their functioning, nonlinear dependencies between system elements and stochasticity of their parameters, etc. The purpose of this work is to develop a simulation model based on the C# programming language for the energy-saving CCGT-110 and ABCM system based on the results of manual analysis according to the data of a full-scale experiment.Method. Methods of linear and nonlinear approximation, methods of energy and thermodynamic analysis, as well as methods of mathematical simulation modeling are used to develop the simulation model.Result.The result of this work is the developed software SAESS 3.0, which allows you to analyze the operation of the CCGT-110 and ABCM systems together and separately in a wide range of parameters and in real time. Conclusion.To assess the adequacy of the developed program, a comparative analysis of software and manual calculation was carried out. Deviations do not exceed an average of 3 %, which confirms the reliability of the simulation model.

Ensuring the environmental safety of residential areas of settlements based on the monitoring of acidic impurities in the atmospheric air кислых примесей в атмосфере

Objectives. Purpose Monitoring of acidic impurities in the atmospheric air of residential areas of settlements is one of the areas of ensuring their environmental safety and is officially carried out at 221 stations in the Russian Federation in the study of atmospheric precipitation.Method. In areas where they are minimal, the author proposes an alternative method for assessing environmental pollution based on the preparation of aerosol suspensions. The purpose of this work was to study the acidity index (pH) of aerosol suspensions (washing off aerosols from the leaves of apricot trees (Prunus armeniaca) obtained in the Srednyaya Akhtuba region (Sredneakhtubinsky district of the Volgograd region) in the spring-summer of 2020.Result. The results of the research demonstrated acidic aerosols ( pH = 5.32 + 0.01) in the atmospheric air rp Srednyaya Akhtuba in comparison with the conditionally clean zone (SNT "Oroshenets", "Shelf"), (pH = 6.39 + 0.02) The data indicate environmental pollution and on environmental risks for the population.Conclusion. Acidic impurities in the atmosphere of the middle Akhtuba region in comparison with the conditionally clean zone (SNT "Oroshenets", "Shelf"), which indicates environmental risks for the population. sources of pollution in residential areas of the settlement of Srednyaya Akhtuba and to develop environmental measures to protect the population from acidic impurities contained in aerosols, which requires further study of the territory.

Design of thermoelectric devices for extracting foreign objects from the human body by freezing

Objectives.The purpose of the article is to consider the designs of thermoelectric devices (TEC) for extracting foreign objects (IO) from the human body by freezing with various options for removing heat from the hot junctions of the thermoelectric module (TEM).Method. Modifications of thermoelectric devices are described for extracting the IO from the human body by freezing it to a special probe. Their technical design differs in the way of heat removal from the TEM hot junctions, for which air heat removal, melting working substances and preliminary cooling of the radiator are used. The basic relationships for calculating the technical means intended for the removal of heat from the hot junctions of the TEM are presented.Result. The graphs of the dependence of the temperature change of the TEM hot junctions in time are obtained for different values of its heat output when using an air heat removal system and the time of complete penetration of various working substances used in the device.Conclusion. The data obtained show that for the operating conditions of the TEC, the temperature of the hot junctions of the TEM with an air heat sink does not go beyond the permissible limits. With a module power of 8 W, 12 W and 16 W, the temperature of the hot junctions of thermoelements stabilizes rather quickly and takes the value of 308 K, 313 K and 318 K. maintaining their stable temperature is most preferred is nickel nitrate, less - elaidic acid and paraffin. Calculations of the design of a device with a pre-cooled radiator system also show the efficiency of heat removal from the hot junctions of the TEM for the duration of the entire procedure for removing the IO from the human body.

Investigation of side electromagnetic radiation generated during the operation of devices with sensory input of information

Objectives. In order to determine the "security" of a special purpose informatization object, it is necessary to calculate the indicators of side electromagnetic radiation generated during the operation of devices with sensor input of information associated with information leakage through technical channels. It is also necessary to develop a list of actions to neutralize potential threats (including the development of an information protection system to protect against this type of threat).Method. The study of side electromagnetic radiation generated during the operation of devices with sensory input of information is carried out using expert documentary and instrumental methods.Result. The results of the study of side electromagnetic radiation generated during the operation of devices with sensor input of information are given and aspects of improving special measures for the protection of information at a special purpose informatization object are determined.Conclusion. The direction of this study is very relevant and requires further development of organizational and technical measures to implement the requirements of regulatory legal documents for the protection of information.

Manufacturing of fiber-reinforced concrete bridge arches

Objective. A new method of manufacturing arches for a fiber-reinforced concrete bridge in the form of an analogue of permanent formwork is considered. Within the framework of this work, research results have been obtained that confirm the effectiveness of the system for the construction of bridge arches of various configurations.Method. The proposed developments will improve the strength characteristics of the bridge arch for small and medium bridges by optimizing the shape and size of the cross section in accordance with the change in the bending moment along the length of the arch. At the same time, reduce its metal consumption by several times.Result. The results obtained confirmed the effectiveness of electrostatic spraying of dry concrete mixture with simultaneous moisture up to moisture, which contributes to the work of capillary forces for compaction of concrete layers and the manufacture of a profiled strong shell (analogue of non-removable reinforced formwork) from reinforced fiber-reinforced concrete.Conclusion. By varying the shape and dimensions of the cross- section, the thickness of the shell and the degree of its reinforcement, as well as filling this shell with high-strength fiber-reinforced concrete, it is possible to design and manufacture bridge arches for various loads.

Determination of coordinates of the earthquake hypocenter by the method of circles

Objective. The aim of the study is to develop a method for determining the coordinates of the earthquake hypocenter using various combinations of second and fourth order figures as a geo-locus of the hypocenter position points.Method. It is known that the line of intersection of figures of the second and fourth orders, in the case of coincidence of focuses, is a circle. To determine the coordinates of the earthquake source, data from seismographs are used, which are used to construct figures of the second and fourth order, the intersection point of which is the hypocenter. When using data from two seismic sensors, there are two figures, the intersection line of which is a circle. A sphere with a radius equal to the radius of the circle is constructed through the center of this circle. For the other two pairs of seismic sensors, two more spheres are also formed, The intersection point of the three spheres obtained is the sought-for hypocenter of the earthquake.Result. A method has been developed for determining the coordinates of an earthquake source using different shapes of the second and fourth orders for different pairs of seismic sensors.Conclusion. The method allows one to select one of the second or fourth order figures for different pairs of seismic sensors, which makes it possible to reduce the error in determining the source coordinates.

Modeling of the dynamics of tornado structures in a pipe with turbulators of square, semicircular and triangular profiles

Objectives. To carry out mathematical simulations of changes in time of tornado compositions in channels with projections of semicircular, triangular, square profiles for average Reynolds criteria based on multiblock computing technology with the solution of finite- volume factorized methods of the Reynolds equation and energy equations.Method. The calculations were carried out on the basis of theoretical approaches based on the solution of Reynolds equations by finite-volume factorized methods, which were closed using the simulation of Menter stresses, and the energy of a structured grid.Result. The calculations of time-dependent flow and heat transfer parameters carried out in the article showed that the excess dissipation of turbulence generation for projections of sharp profiles - square profile, triangular profile - and rounded profiles - semicircular profile, segment profile - is provided with radically different hydraulic losses: channels with protrusions of rounded profiles, for example, semicircular, have much lower hydraulic resistance coefficients than channels with protrusions with sharp profiles, for example, triangular or square, rectangular.Conclusion. In the article, mathematical simulations of time-dependent tornado compositions were performed in channels with transversal profiles in the form of a square, triangle and semicircle, which is as informative as possible in terms of studying turbulent flows and heat transfer arising under average Reynolds criteria based on computer multiblock technology when using solutions of finite-volume factorized methods (FCOM-am) Reynolds equations and energy equations. The following protrusions were considered in the article: square transversal profiles, in which tornadoes are most pronounced, and side tornadoes affect the flow in the maximum way; triangular transversal profiles, where tornadoes are not so strong, and side tornadoes affect the main flow weaker than with square protrusions; semicircular transversal profiles, in which the incoming main tornado moves along the stream with the generation of limited side tornadoes. The calculated information obtained in the article correlates to a high degree with the available experimental data, which indicates the verification of the mathematical modeling involved in the article.

Development of information security model with application of production model

Objective. The purpose of the study is to find methods for solving the problem of ensuring a reliable level of security for cloud services. Production models can be considered the most common models that provide simplicity of knowledge representation and inference organization.Method. The research is based on the application of methods of fuzzy logic and mathematical modeling.Result. It is proposed to use fuzzy models that provide a flexible strategy for processing heterogeneous dynamic interacting processes that represent data and knowledge in an essentially fuzzy state space of objects of analysis.Conclusion. A production model of information security management is proposed, which is used to create data processing and storage centers. The production system includes a rule base, a global database, and a rule interpreter. The effective use of large information resources operating in an uncertain environment on the basis of a production model makes it possible to model and ensure information security of systems.

Algorithm of fire detection for multi-sensor system

Objective. The paper proposes a fire detection algorithm for a multisensor system. Due to the difficult conditions in the field, for the first time, watch rescue operations are difficult and often endanger the lives of rescuers. The main scientific goal is for the system to work autonomously on certain segments of the monitoring process, while the three agents, to varying degrees, must interact with each other based on communication and decision-making algorithms.Method. There are many algorithms for image processing, but algorithms that use several sources of information are not sufficiently developed and described. The focus is on fire detection algorithms. The algorithm was developed using NI Vision Assistant, a software tool for rapid prototyping and testing of imaging applications.Result. In addition to the software implementation in C, which NI Vision Assistant generates by default, the paper presents a Python implementation of the algorithm.Conclusion. The results of the work can be used to develop multisensor systems for monitoring hard-to-reach areas.

Optimization of the parameters of truss beams with two posts

Based on the theoretical results obtained in the article [17], here the analysis of the influence of various design parameters on the own weight and cost of metal of truss beams with two posts is carried out. An optimal parameter has been obtained that makes it possible to reduce the calculated bending moment in the cross section of a truss beam with two struts.Method. By equalizing the bending moments in various design sections of the truss beam, the internal force factors are reduced. The corresponding equation for optimizing the parameters of the beam has been drawn up and a formula has been obtained to determine the optimal parameter of the structure as a whole.Result. Using the example of numerical calculations, a decrease in the calculated bending moment by 14% compared to truss beams without optimization is shown.Conclusion. The proposed method and algorithm testify to the efficiency and rationality of the obtained optimal parameter of the structure as a whole.