Heat Transfer Enhancement of Air Flowing Across Grooved Channels: Joint Effects of Channel Height and Groove Depth

2008 ◽  
Vol 130 (2) ◽  
Author(s):  
El Hassan Ridouane ◽  
Antonio Campo
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Parallel Plate ◽  
Numerical Study ◽  
Local Heat Transfer ◽  
Groove Depth ◽  
Channel Height ◽  
Transfer Enhancement ◽  
Maximum Heat ◽  
Maximum Heat Transfer

A numerical study was conducted to investigate convective heat transfer and laminar fluid flow in the developing region of two-dimensional parallel-plate channels with arrays of transverse hemicircular grooves cut into the plates. Air with uniform velocity and temperature enters the channel whose plates are at a uniform temperature. The finite-volume method is used to perform the computational analysis accounting for the traditional second-order-accurate QUICK and SIMPLE schemes. Steady-state results are presented for parallel-plate channels with and without hemicircular grooves for comparison purposes. The study revolves around four controlling parameters: (1) the height of the channel, (2) the relative groove depth, (3) the number of grooves, and (4) the Reynolds number. A prototypical 120‐cm-long channel contains two series of 3, 6, and 12 transverse grooves with four relative groove depths δ∕D of 0.125, 0.25, 0.375, and 0.5. Three ratios of channel height to groove print diameter H∕D of 0.5, 1, and 2 are employed. Computations are performed for Reynolds numbers based on the hydraulic diameter ranging from 1000 to 2500. It is found that the grooves enhance local heat transfer relative to a flat passage at locations near their downstream edge. The maximum heat transfer enhancement occurs at an optimal depth of the grooves. For purposes of engineering design, generalized correlation equations for the Nusselt number in terms of the pertinent Re, δ∕D, and the number of grooves N were constructed using nonlinear regression theory.

Enhancement of Natural Convection Heat Transfer by a Staggered Array of Discrete Vertical Plates

1980 ◽  
Vol 102 (2) ◽  
pp. 215-220 ◽  
Author(s):  
E. M. Sparrow ◽  
C. Prakash
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Heat Transfer Enhancement ◽  
Parallel Plate ◽  
Convection Heat Transfer ◽  
Transfer Enhancement ◽  
Enhanced Heat Transfer ◽  
Maximum Heat ◽  
Maximum Heat Transfer ◽  
Parameter Ranges

An analysis has been performed to determine whether, in natural convection, a staggered array of discrete vertical plates yields enhanced heat transfer compared with an array of continuous parallel vertical plates having the same surface area. The heat transfer results were obtained by numerically solving the equations of mass, momentum, and energy for the two types of configurations. It was found that the use of discrete plates gives rise to heat transfer enhancement when the parameter (Dh/H)Ra > ∼2 × 103 (Dh = hydraulic diameter of flow passage, H = overall system height). The extent of the enhancement is increased by use of numerous shorter plates, by larger transverse interplate spacing, and by relatively short system heights. For the parameter ranges investigated, the maximum heat transfer enhancement, relative to the parallel plate case, was a factor of two. The general degree of enhancement compares favorably with that which has been obtained in forced convection systems.

An Experiment Investigation of Heat Transfer Enhancement by Pulsating Laminar Flow in Rectangular Grooved Channels

2013 ◽  
Vol 732-733 ◽  
pp. 74-77
Author(s):  
Yan Li ◽  
Dong Xu Jin ◽  
Yan Qin Jing ◽  
Bing Chang Yang
Keyword(s):  
Heat Transfer ◽  
Laminar Flow ◽  
Heat Transfer Enhancement ◽  
Enhancement Factor ◽  
Groove Depth ◽  
Pulsating Flow ◽  
Pulsation Frequency ◽  
Transfer Enhancement ◽  
Maximum Heat ◽  
Maximum Heat Transfer

In this paper, the heat transfer enhancement by pulsating laminar flow in rectangular grooved channels was experimentally investigated. Effects of Reynolds number Re, pulsation frequency, groove depth and groove length on the heat transfer enhancement were studied. Experimental results show that Nusselt number increases with Re increases both in steady and pulsating flow cases. Pulsating flow can efficiently enhance heat transfer in the grooved channels and the heat transfer enhancement factor increases with the increase of Re. There exists an optimal pulsation frequency, corresponding to the maximum heat transfer enhancement factor, which is almost the same for different Re, groove depth and groove length.

Effect of Periodicity of Non-Uniform Sinusoidal Side Heating on Natural Convection in an Anisotropic Porous-Enclosure

2011 ◽  
Vol 110-116 ◽  
pp. 1613-1618 ◽  
Author(s):  
S. Kapoor ◽  
P. Bera
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Natural Convection ◽  
Stream Function ◽  
Numerical Study ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Maximum Heat ◽  
Maximum Heat Transfer ◽  
Porous Enclosure

A comprehensive numerical study on the natural convection in a hydrodynamically anisotropic as well as isotropic porous enclosure is presented, flow is induced by non uniform sinusoidal heating of the right wall of the enclosure. The principal directions of the permeability tensor has been taken oblique to the gravity vector. The spectral Element method has been adopted to solve numerically the governing differential equations by using the vorticity-stream-function approach. The results are presented in terms of stream function, temperature profile and Nusselt number. The result show that the maximum heat transfer takes place at y = 1.5 when N is odd.. Also, increasing media permeability, by changing K* = 1 to K* = 0.2, increases heat transfer rate at below and above right corner of the enclosure. Furthermore, for the all values of N, profiles of local Nusselt number (Nuy) in isotropic as well as anisotropic media are similar, but for even values of N differ slightly at N = 2.. In particular the present analysis shows that, different periodicity (N) of temperature boundary condition has the significant effect on the flow pattern and consequently on the local heat transfer phenomena.

A Numerical Study of Heat Transfer Enhancement by a Rectangular Cylinder Placed Parallel to the Heated Wall

2019 ◽  
Vol 141 (7) ◽  
Author(s):  
J. F. Derakhshandeh ◽  
Md. Mahbub Alam
Keyword(s):  
Heat Transfer ◽  
Vortex Dynamics ◽  
Numerical Study ◽  
Vortex Street ◽  
Heated Wall ◽  
Transfer Enhancement ◽  
Maximum Heat ◽  
Single Row ◽  
Rectangular Cylinder ◽  
Maximum Heat Transfer

The flow around a rectangular cylinder mounted in the vicinity of a hot wall is numerically studied at a Reynolds number of 200. While the cylinder chord-to-height ratio C/W is varied from 2 to 10, the gap distance G from the wall to the cylinder is changed from 0.25 to 6.25. The focus of this study is given on the dependence of G/W and C/W on the heat transfer from the wall and associated physics. The variation in the Strouhal number is presented as a function of C/W. It is observed that the effect of G/W on the vortex dynamics and heat transfer is much more than that of C/W. Based on the dependence of the vortex dynamics and heat transfer on G/W, we have identified four distinct flows: no vortex street flow (G/W < 0.75), single-row vortex street flow (0.75 ≤ G/W ≤ 1.25), inverted two-row vortex street flow (1.25 < G/W ≤ 2.5), and two-row vortex street flow (G/W > 2.5). At the single-row vortex street flow, the two opposite-sign vortices appearing in a jetlike flow carry heat from the wall to the wake and then to the freestream. The maximum heat transfer is achieved at the single-row vortex street flow and 8% increase occurs at C/W = 2, G/W = 0.75–1.25.

Heat Transfer Enhancement Induced by Cube- and Diamond-Shaped Block Arrays in Two-Pass High-Aspect Ratio Channels With a 180-Degree Turn

2010 ◽  
Author(s):  
Pavin Ganmol ◽  
Minking K. Chyu
Keyword(s):  
Heat Transfer ◽  
Aspect Ratio ◽  
Heat Transfer Enhancement ◽  
High Aspect Ratio ◽  
Local Heat Transfer ◽  
Channel Height ◽  
Transfer Enhancement ◽  
Smooth Channel ◽  
Sharp Turn ◽  
First Pass

Described in this paper is an experimental investigation of the heat transfer and pressure characteristics in a high aspect ratio, (4.5:1 width-to-height), two-pass channel, with cube-shaped and diamond-shaped block arrays placed in both passes before and after a 180-degree sharp turn. Transient liquid crystal technique was applied to acquire detailed local heat transfer data on both the channel surfaces and the block elements. Reynolds number tested varies between 13000 and 28000. To further explore potential design alternatives for enhancement cooling, the effects of block height, ranging from 1/4, 1/2, 3/4 and full span of the channel height were also evaluated. Present results suggest that a staggered cube-array can enhance heat transfer rate up to 3.5 fold in the first pass and about 1.9 fold in the second pass, relative to the fully-developed smooth channel counterpart. For the corresponding diamond-shaped block array, the enhancement is 3.4 and 1.9 fold respectively. Even though the post-turn turbulence transport in the second pass is generally higher than that in the first pass, the effects of surface-block induced heat transfer enhancement in fact are less prominent in the post-turn region of the second pass. Pressure loss for diamond block arrays is generally higher than that of the corresponding cube-block arrays.

scholarly journals Investigation of the novelty of latent functionally thermal fluids as alternative to nanofluids in natural convective flows

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Zoubida Haddad ◽  
Farida Iachachene ◽  
Eiyad Abu-Nada ◽  
Ioan Pop
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Heat Transfer Enhancement ◽  
Volume Fraction ◽  
Heat Of Fusion ◽  
Transfer Enhancement ◽  
Maximum Heat ◽  
Thermal Fluids ◽  
Maximum Heat Transfer ◽  
Wide Range

AbstractThis paper presents a detailed comparison between the latent functionally thermal fluids (LFTFs) and nanofluids in terms of heat transfer enhancement. The problem used to carry the comparison is natural convection in a differentially heated cavity where LFTFs and nanofluids are considered the working fluids. The nanofluid mixture consists of Al2O3 nanoparticles and water, whereas the LFTF mixture consists of a suspension of nanoencapsulated phase change material (NEPCMs) in water. The thermophysical properties of the LFTFs are derived from available experimental data in literature. The NEPCMs consist of n-nonadecane as PCM and poly(styrene-co-methacrylic acid) as shell material for the encapsulation. Finite volume method is used to solve the governing equations of the LFTFs and the nanofluid. The computations covered a wide range of Rayleigh number, 104 ≤ Ra ≤ 107, and nanoparticle volume fraction ranging between 0 and 1.69%. It was found that the LFTFs give substantial heat transfer enhancement compared to nanofluids, where the maximum heat transfer enhancement of 13% was observed over nanofluids. Though the thermal conductivity of LFTFs was 15 times smaller than that of the base fluid, a significant enhancement in thermal conductivity was observed. This enhancement was attributed to the high latent heat of fusion of the LFTFs which increased the energy transport within the cavity and accordingly the thermal conductivity of the LFTFs.

An Experimental Investigation of Heat Transfer Enhancement by Pulsating Laminar Flow in a Triangular Grooved Channel

2012 ◽  
Vol 516-517 ◽  
pp. 249-252 ◽  
Author(s):  
Bing Chang Yang ◽  
Dong Xu Jin
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Enhancement ◽  
Strouhal Number ◽  
Enhancement Factor ◽  
Pulsating Flow ◽  
Transfer Enhancement ◽  
Maximum Heat ◽  
Pulsation Amplitude ◽  
Maximum Heat Transfer

Heat transfer enhancement by pulsating flow in a triangular grooved channel has been experimentally investigated. Effects of Reynolds number Re, Strouhal number St, pulsation amplitude A on the heat transfer enhancement were studied. The experimental results show that, the pulsating flow can significantly enhance heat transfer compared to the steady flow case, for instance, an enhancement of 115% is achieved at Re=400, A=0.5 and St=0.3. There exists an optimal Strouhal number corresponding to the maximum heat transfer enhancement factor. The heat transfer enhancement factor increases with the increase of Reynolds number and pulsation amplitude.

Heat Transfer Enhancement in Turbulent Ribbed-Pipe Flow

2017 ◽  
Vol 139 (7) ◽  
Author(s):  
Changwoo Kang ◽  
Kyung-Soo Yang
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Pipe Flow ◽  
Joint Probability ◽  
Turbulent Heat Transfer ◽  
Immersed Boundary ◽  
Turbulent Heat ◽  
Transfer Enhancement ◽  
Maximum Heat ◽  
Maximum Heat Transfer

The present study aims at explaining why heat transfer is enhanced in turbulent ribbed-pipe flow, based on our previous large eddy simulation (LES) database (Kang and Yang, 2016, “Characterization of Turbulent Heat Transfer in Ribbed Pipe Flow,” ASME J. Heat Transfer, 138(4), p. 041901) obtained for Re = 24,000, Pr = 0.71, pitch ratio (PR) = 2, 4, 6, 8, 10, and 18, and blockage ratio (BR) = 0.0625. Here, the bulk velocity and the pipe diameter were used as the velocity and length scales, respectively. The ribs were implemented in the cylindrical coordinate system by means of an immersed boundary method. In particular, we focus on the cases of PR ≥ 4 for which heat transfer turns out to be significantly enhanced. Instantaneous flow fields reveal that the vortices shed from the ribs are entrained into the main recirculating region behind the ribs, inducing velocity fluctuations in the vicinity of the pipe wall. In order to identify the turbulence structures responsible for heat transfer enhancement in turbulent ribbed-pipe flow, various correlations among the fluctuations of temperature and velocity components have been computed and analyzed. The cross-correlation coefficient and joint probability density distributions of velocity and temperature fluctuations, obtained for PR = 10, confirm that temperature fluctuation is highly correlated with velocity-component fluctuation, but which component depends upon the axial location of interest between two neighboring ribs. Furthermore, it was found via the octant analysis performed for the same PR that at the axial point of the maximum heat transfer rate, O3 (cold wallward interaction) and O5 (hot outward interaction) events most contribute to turbulent heat flux and most frequently occur.

Numerical Investigation of Heat Transfer Enhancement Using Hybrid Vortex Generator Arrays in Fin-and-Tube Heat Exchangers

2016 ◽  
Vol 8 (3) ◽  
Author(s):  
Shubham Agarwal ◽  
R. P. Sharma
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Heat Transfer Enhancement ◽  
Heat Exchangers ◽  
Numerical Study ◽  
Vortex Generator ◽  
Roll Angle ◽  
Transfer Enhancement ◽  
Maximum Heat ◽  
Hybrid Configuration

This is a novel study for assessing the heat transfer enhancement in a multi-row inline-tube heat exchanger using hybrid vortex generator (VG) arrays, i.e., rectangular winglet pairs (RWPs) with different geometrical configurations installed in coherence for enhanced heat transfer. The three-dimensional numerical study uses a full scale seven-tube inline heat exchanger model. The effect of roll of rectangular winglet VG on heat transfer enhancement is analyzed and optimized roll angle is determined for maximum heat transfer enhancement. Four different configurations are analyzed and compared in this regard: (a) single RWP (no roll); (b) 3RWP-inline array(alternating tube row with no roll of VGs); (c) single RWP (with optimized roll angle VGs); and (d) 3RWP-inline array(alternating tube row with all VGs having optimized roll angle). It was found that the inward roll of VGs increased the heat transfer from the immediately downstream tube but reduced heat transfer enhancement capability of other VG pairs downstream. Further, four different hybrid configurations of VGs were analyzed and the optimum configuration was obtained. For the optimized hybrid configuration at Re = 670, RWP with optimized roll angle increased heat transfer by 17.5% from the tube it was installed on and by 42% from the immediately downstream tube. Increase in j/ƒ of 36.7% is obtained by use of hybrid VGs in the optimized hybrid configuration. The deductions from the current study are supposed to well enhance the performance of heat exchangers with different design configurations.

Compounded Heat Transfer Enhancement in Enclosure Natural Convection by Changing the Cold Wall Shape and the Gas Composition

2006 ◽  
Vol 129 (7) ◽  
pp. 827-834 ◽  
Author(s):  
El Hassan Ridouane ◽  
Antonio Campo
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Heat Transfer Enhancement ◽  
Gas Mixtures ◽  
Gas Mixture ◽  
Transfer Enhancement ◽  
Maximum Enhancement ◽  
Maximum Heat ◽  
Maximum Heat Transfer ◽  
Triangular Enclosure

This article addresses compound heat transfer enhancement for gaseous natural convection in closed enclosures; that is, the simultaneous use of two passive techniques to obtain heat transfer enhancement, which is greater than that produced by only one technique itself. The compounded heat transfer enhancement comes from two sources: (1) reshaping the bounded space and (2) the adequacy of the gas. The sizing of enclosures is of great interest in the miniaturization of electronic packaging that is severely constrained by space and∕or weight. The gases consist in a subset of binary gas mixtures formed with helium (He) as the primary gas. The secondary gases are nitrogen (N2), oxygen (O2), carbon dioxide (CO2), methane (CH4), and xenon (Xe). The steady-state flow is governed by a system of 2-D coupled mass, momentum, and energy conservation equations, in conjunction with the ideal gas equation of state. The set of partial differential equations is solved using the finite volume method, for a square and a right-angled isosceles triangular enclosure, accounting for the second-order accurate QUICK and SIMPLE schemes. The grid layouts rendered reliable velocities and temperatures for air and the five gas mixtures at high Ra=106, producing errors within 1% were 18,500 and 47,300 elements for the square and triangle enclosures, respectively. In terms of heat transfer enhancement, helium is better than air for the square and the isosceles triangle. It was found that the maximum heat transfer conditions are obtained filling the isosceles triangular enclosure with a He–Xe gas mixture. This gives a good trade-off between maximizing the heat transfer rate while reducing the enclosure space in half; the maximum enhancement of triangle∕square went up from 19% when filled with air into 46% when filled with He–Xe gas mixture at high Ra=106.

Sign in / Sign up

Export Citation Format

Share Document