The Structure of Tip Clearance Flow in Axial Flow Compressors

1995 ◽  
Vol 117 (3) ◽  
pp. 336-347 ◽  
Author(s):  
B. Lakshminarayana ◽  
M. Zaccaria ◽  
B. Marathe
Keyword(s):  
Axial Flow ◽  
Tip Clearance ◽  
Complex Nature ◽  
Tip Leakage Flow ◽  
Tip Clearance Flow ◽  
Wall Boundary Layer ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Blade Tip ◽  
Flow Compressor

Detailed measurements of the flow field in the tip region of an axial flow compressor rotor were carried out using a rotating five-hole probe. The axial, tangential, and radial components of relative velocity, as well as the static and stagnation pressures, were obtained at two axial locations, one at the rotor trailing edge, the other downstream of the rotor. The measurements were taken up to about 26 percent of the blade span from the blade tip. The data are interpreted to understand the complex nature of the flow in the tip region, which involves the interaction of the tip leakage flow, the annulus wall boundary layer and the blade wake. The experimental data show that the leakage jet does not roll up into a vortex. The leakage jet exiting from the tip gap is of high velocity and mixes quickly with the mainstream, producing intense shearing and flow separation. There are substantial differences in the structure of tip clearance observed in cascades and rotors.

Numerical Investigations of the Coupled Flow Through a Subsonic Compressor Rotor and Axial Skewed Slot

2008 ◽  
Vol 131 (1) ◽  
Author(s):  
Xingen Lu ◽  
Wuli Chu ◽  
Junqiang Zhu ◽  
Yangfeng Zhang
Keyword(s):  
Axial Flow ◽  
Tip Clearance ◽  
Stall Margin ◽  
Tip Clearance Flow ◽  
Casing Treatment ◽  
Axial Flow Compressor ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Flow Through ◽  
Flow Compressor

In order to advance the understanding of the fundamental mechanisms of axial skewed slot casing treatment and their effects on the subsonic axial-flow compressor flow field, the coupled unsteady flow through a subsonic compressor rotor and the axial skewed slot was simulated with a state-of-the-art multiblock flow solver. The computational results were first compared with available measured data, that showed the numerical procedure calculates the overall effect of the axial skewed slot correctly. Then, the numerically obtained flow fields were interrogated to identify the physical mechanism responsible for improvement in stall margin of a modern subsonic axial-flow compressor rotor due to the discrete skewed slots. It was found that the axial skewed slot casing treatment can increase the stall margin of subsonic compressor by repositioning of the tip clearance flow trajectory further toward the trailing of the blade passage and retarding the movement of the incoming∕tip clearance flow interface toward the rotor leading edge plane.

scholarly journals Numerical and Experimental Investigations of Steady Micro-Tip Injection on a Subsonic Axial-Flow Compressor Rotor

2006 ◽  
Vol 2006 ◽  
pp. 1-11 ◽  
Author(s):  
Xingen Lu ◽  
Wuli Chu ◽  
Junqiang Zhu ◽  
Zhiting Tong
Keyword(s):  
Mass Flow ◽  
Axial Flow ◽  
Tip Clearance ◽  
Air Injection ◽  
Stall Margin ◽  
Tip Clearance Flow ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Tip Injection ◽  
Flow Compressor

Steady tip injection has been demonstrated to be an effective means of extending the stable operating range of a tip-critical compressor. This study presents a state-of-the-art design for the tip injection through the casing with flush-mounted inclined holes and the effectiveness of steady micro-air injection to enhance stability in a subsonic axial-flow compressor rotor using an external-air supply. For the tested rotor, experimental results demonstrate that at 53% design speed, the stalling mass flow can be reduced by 7.69% using an injected mass flow equivalent to 0.064% of the annulus flow. Time-dependent CFD simulations were conducted to identify the physical mechanic that accounts for the beneficial effects of the steady micro-air injection on the performance and stability of the compressor. Detailed analyses of the flow visualization at the tip have exposed the different tip flow topologies between the cases without tip injection and with tip injection. It was found that the primary stall margin enhancement afforded by the steady micro-air injection is a result of the tip-clearance flow manipulation. The repositioning of the tip-clearance vortex further towards the trailing edge of the blade passage and delaying the movement of incoming/tip-clearance flow interface to the leading edge plane are the physical mechanisms responsible for extending the compressor stall margin.

An Experimental Study of the Compressor Rotor Blade Boundary Layer

1985 ◽  
Vol 107 (2) ◽  
pp. 364-372 ◽  
Author(s):  
M. Pouagare ◽  
J. M. Galmes ◽  
B. Lakshminarayana
Keyword(s):  
Boundary Layer ◽  
Rotor Blade ◽  
Radial Profile ◽  
Three Dimensional ◽  
Axial Flow ◽  
Tip Leakage Flow ◽  
Wall Boundary Layer ◽  
Compressor Rotor ◽  
Blade Tip ◽  
Flow Compressor

The three-dimensional turbulent boundary layer developing on a rotor blade of an axial flow compressor was measured using a minature “x” configuration hot-wire probe. The measurements were carried out at nine radial locations on both surfaces of the blade at various chordwise locations. The data derived includes streamwise and radial mean velocities and turbulence intensities. The validity of conventional velocity profiles such as the “power law profile” for the streamwise profile, and Mager and Eichelbrenner’s for the radial profile, is examined. A modification to Mager’s crossflow profile is proposed. Away from the blade tip, the streamwise component of the blade boundary layer seems to be mainly influenced by the streamwise pressure gradient. Near the tip of the blade, the behavior of the blade boundary layer is affected by the tip leakage flow and the annulus wall boundary layer. The “tangential blockage” due to the blade boundary layer is derived from the data. The profile losses are found to be less than that of an equivalent cascade, except in the tip region of the blade.

scholarly journals Effect of Circumferential Single Casing Groove Location on the Flow Stability under Tip-Clearance Effect in a Transonic Axial Flow Compressor Rotor

Energies ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 6143
Author(s):  
Xiaoxiong Wu ◽  
Bo Liu ◽  
Botao Zhang ◽  
Xiaochen Mao
Keyword(s):  
Control Mechanism ◽  
Incidence Angle ◽  
Axial Flow ◽  
Flow Stability ◽  
Tip Clearance ◽  
Tip Leakage Flow ◽  
Flow Angle ◽  
Axial Flow Compressor ◽  
Compressor Rotor ◽  
Flow Compressor

Numerical simulations have been performed to study the effect of the circumferential single-grooved casing treatment (CT) at multiple locations on the tip-flow stability and the corresponding control mechanism at three tip-clearance-size (TCS) schemes in a transonic axial flow compressor rotor. The results show that the CT is more efficient when its groove is located from 10% to 40% tip axial chord, and G2 (located at near 20% tip axial chord) is the best CT scheme in terms of stall-margin improvement for the three TCS schemes. For effective CTs, the tip-leakage-flow (TLF) intensity, entropy generation and tip-flow blockage are reduced, which makes the interface between TLF and mainstream move downstream. A quantitative analysis of the relative inlet flow angle indicates that the reduction of flow incidence angle is not necessary to improve the flow stability for this transonic rotor. The control mechanism may be different for different TCS schemes due to the distinction of the stall inception process. For a better application of CT, the blade tip profile should be further modified by using an optimization method to adjust the shock position and strength during the design of a more efficient CT.

Behavior of Tip Leakage Flow in an Axial Flow Compressor Rotor

2006 ◽  
Author(s):  
Yanhui Wu ◽  
Wuli Chu ◽  
Xingen Lu ◽  
Junqiang Zhu
Keyword(s):  
Boundary Layer ◽  
Vortex Breakdown ◽  
Axial Flow ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Pressure Side ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Flow Compressor

The current paper reports on investigations with an aim to advance the understanding of the flow field near the casing of a small-scale high-speed axial flow compressor rotor. Steady three dimensional viscous flow calculations are applied to obtain flow fields at various operating conditions. To demonstrate the validity of the computation, the numerical results are first compared with available measured data. Then, the numerically obtained flow fields are analyzed to identify the behavior of tip leakage flow, and the mechanism of blockage generation arising from flow interactions between the tip clearance flow, the blade/casing wall boundary layers, and non-uniform main flow. The current investigation indicates that the “breakdown” of the tip leakage vortex occurs inside the rotor passage at the near stall condition. The vortex “breakdown” results in the low-energy fluid accumulating on the casing wall spreads out remarkably, which causes a sudden growth of the casing wall boundary layer having a large blockage effect. A low-velocity region develops along the tip clearance vortex at the near stall condition due to the vortex “breakdown”. As the mass flow rate is further decreased, this area builds up rapidly and moves upstream. This area prevents incoming flow from passing through the pressure side of the passage and forces the tip leakage flow to spill into the adjacent blade passage from the pressure side at the leading edge. It is found that the tip leakage flow exerts little influence on the development of the blade suction surface boundary layer even at the near stall condition.

Investigation of the Tip Clearance Flow Inside and at the Exit of a Compressor Rotor Passage—Part I: Mean Velocity Field

1983 ◽  
Vol 105 (1) ◽  
pp. 1-12 ◽  
Author(s):  
A. Pandya ◽  
B. Lakshminarayana
Keyword(s):  
Boundary Layer ◽  
Tip Clearance ◽  
Mean Flow ◽  
Ensemble Averaging ◽  
Mean Velocity ◽  
Tip Clearance Flow ◽  
Wall Boundary Layer ◽  
Compressor Rotor ◽  
Wall Boundary ◽  
Clearance Flow

This paper reports on an experimental study of the nature of the tip clearance flow in a moderately loaded compressor rotor. The measurements reported were obtained using a stationary two-sensor, hot-wire probe in combination with an ensemble averaging technique. The flow field was surveyed at various radial locations and at ten axial locations, four of which were inside the blade passage in the clearance region and the remaining six outside the passage. Variations of the mean flow properties in the tangential and the radial directions at various axial locations were derived from the data. Variation of leakage velocity at different axial stations and the annulus-wall boundary layer profiles from passage-averaged mean velocities were also estimated. The results indicate that there exists a region of strong interaction of the leakage flow with the annulus-wall boundary layer at half-chord. The profiles are well-behaved beyond this point. The rotor exit flow is found to be uniform beyond 3/4 blade chord downstream of the rotor trailing edge.

Effect of Axially Non-Uniform Rotor Tip Clearance on the Performance of a High Speed Axial Flow Compressor Stage

1994 ◽  
Author(s):  
K. Mohan ◽  
S. A. Guruprasad
Keyword(s):  
High Speed ◽  
Axial Flow ◽  
Separated Flow ◽  
Tip Clearance ◽  
Compressor Stage ◽  
Tip Leakage Flow ◽  
Suction Surface ◽  
Wall Boundary Layer ◽  
Improved Performance ◽  
Flow Compressor

An axially non-uniform type of rotor tip clearance was conceived and tried on a single stage compressor. This concept is based on the advantages of a smaller tip clearance in the front portion of the blade and a larger clearance in the rear portion which allows a higher tip leakage flow to interact with the passage secondary flow, casing wall boundary layer, separated flow on the blade suction surface and the scraping vortex, which are more prominent at the rear portion of the blade. Experimental results indicated that an axially non-uniform clearance can provide improved performance of a compressor stage. Providing the tip clearance in the compressor casing instead of at the blade tip indicated certain advantages. An ‘optimum’ value of rotor tip clearance was noticed for this compressor stage, both for axially uniform and axially non-uniform clearance.

Numerical Investigation of Tip Clearance Flow in an Axial Compressor Cascade

2014 ◽  
Vol 599-601 ◽  
pp. 368-371
Author(s):  
Zhi Hui Xu ◽  
He Bin Lv ◽  
Ru Bin Zhao
Keyword(s):  
Computational Simulation ◽  
Suction Side ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Compressor Cascade ◽  
Tip Leakage Flow ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Clearance Flow ◽  
Blade Tip

Using blade tip winglet to control the tip leakage flow has been concerned in the field of turbomachinery. Computational simulation was conducted to investigate the phenomenological features of tip clearance flow. The simulation results show that suction-side winglet can reduce leakage flow intensity. The tip winglet can also decrease tip leakage mass flow and weaken tip leakage flow mixing with the mainstream and therefore reduce the total pressure loss at the blade tip.

Numerical Simulation of Tip Clearance Flow Control in Axial Turbine Rotor: Part 1—Active Flow Control Injection From Turbine Blade Tip

2008 ◽  
Author(s):  
Wei Li ◽  
Wei-Yang Qiao ◽  
Kai-Fu Xu ◽  
Hua-Ling Luo
Keyword(s):  
Flow Control ◽  
Turbine Blade ◽  
Stokes Equations ◽  
Tip Clearance ◽  
Tip Leakage Flow ◽  
Injection Hole ◽  
Tip Clearance Flow ◽  
Clearance Flow ◽  
Flow Part ◽  
Blade Tip

Reducing loss and increasing efficiency are always pursued in the designing of the turbine, and flow control is an efficient solution to minimize the tip clearance loss. Recently it aroused much attention in the field of the turbine tip clearance flow. Part-1 of this paper aims to numerically investigate the effect of active turbine clearance flow control by injection from a turbine blade tip on the tip clearance flow. Part-2 of this paper focus on the passive turbine tip clearance flow control. A density-correction based, 3D Reynolds-averaged Navier-Stokes equations CFD code with Reynolds Stress Model, which was proved to be validated, was adopted. The variable specific heat was considered. The effects of injection on the tip clearance flow were simulated in two tip clearance heights, and each height corresponds to five injection hole locations and five injection mass flow rates. Accordingly, the mechanisms of active injection control were put in evidence; the effects of the injection on the turbine efficiency which includes the effect of the jet and the tip clearance flow were highlighted; and the tip clearance flow structure was analyzed topologically. If the tip leakage flow corresponding to the injection location is subsonic, this injection can increase the efficiency, such as the first and the second jet. The combined jet could increase the efficiency by 0.35% for the case of loose tip clearance and by 0.3% for the case of tight tip clearance. The number of saddle points was equal to that of nodes near the injection hole, which could satisfy the singularity point total number law.

Experimental Investigation on Tip Clearance Flow of Compressor Cascade With Blade Tip Winglet

2012 ◽  
Author(s):  
Shaobing Han ◽  
Jingjun Zhong ◽  
Huawei Lu ◽  
Xiaoxu Kan ◽  
Haiyang Gao
Keyword(s):  
Flow Field ◽  
Passive Control ◽  
Control Strategies ◽  
Suction Side ◽  
Tip Clearance ◽  
Compressor Cascade ◽  
Tip Leakage Flow ◽  
Tip Clearance Flow ◽  
Clearance Flow ◽  
Blade Tip

This paper presents the results of experimental research of flow in an axial compressor cascade with different types of winglet on the blade tip, which consists of a suction-side winglet, pressure-side winglet and the combined winglet. The detailed tip leakage flow field with different winglet was described with total pressure loss coefficient, secondary streamline and axial vorticity on the cascade exit flow field. The mechanisms of the three passive control methods were illuminated. The result indicated that the tip clearance flow strengths could be reduced in all the three control strategies. The compressor aerodynamic performance could be improved via the addition of tip winglets. The suction-side winglet had the best effect on the cascade flow field, and the strength of leakage vortex and the associated mixture losses were reduced.

Sign in / Sign up

Export Citation Format

Share Document