Numerical Simulation of Impeller–Volute Interaction in Centrifugal Compressors

1999 ◽  
Vol 121 (3) ◽  
pp. 603-608 ◽  
Author(s):  
K. Hillewaert ◽  
R. A. Van den Braembussche
Keyword(s):  
Numerical Simulation ◽  
Boundary Conditions ◽  
Unsteady Flow ◽  
Centrifugal Compressor ◽  
Three Dimensional ◽  
Numerical Procedure ◽  
Flow Calculation ◽  
Total Temperature ◽  
Temperature And Pressure ◽  
Good Agreement

A numerical procedure to predict the impeller–volute interaction in a single-stage centrifugal compressor is presented. The method couples a three-dimensional unsteady flow calculation in the impeller with a three-dimensional time-averaged flow calculation in the volute through an iterative updating of the boundary conditions on the interface of both calculation domains. The method has been used to calculate the flow in a compressor with an external volute at off-design operation. Computed circumferential variations of flow angles, total temperature, and pressure are shown and compared with measurements. The good agreement between the predictions and measurements confirms the validity of the approach.

Numerical Simulation of Impeller–Volute Interaction in Centrifugal Compressors

1998 ◽  
Author(s):  
Koen Hillewaert ◽  
René A. Van den Braembussche
Keyword(s):  
Numerical Simulation ◽  
Boundary Conditions ◽  
Unsteady Flow ◽  
Centrifugal Compressor ◽  
Three Dimensional ◽  
Numerical Procedure ◽  
Flow Calculation ◽  
Total Temperature ◽  
Temperature And Pressure ◽  
Good Agreement

A numerical procedure to predict the impeller/volute interaction in a single-stage centrifugal compressor is presented. The method couples a three-dimensional unsteady flow calculation in the impeller with a three-dimensional time-averaged flow calculation in the volute through an iterative updating of the boundary conditions on the interface of both calculation domains. The method has been used to calculate the flow in a compressor with an external volute at off-design operation. Computed circumferential variations of flow angles, total temperature and pressure are shown and compared with measurements. The good agreement between the predictions and measurements confirms the validity of the approach.

The Calculation of Three Dimensional Viscous Flow Through Multistage Turbomachines

1990 ◽  
Author(s):  
J. D. Denton
Keyword(s):  
Boundary Conditions ◽  
Unsteady Flow ◽  
Viscous Flow ◽  
Calculation Method ◽  
Three Dimensional ◽  
Mixing Process ◽  
Three Dimensional Flow ◽  
Flow Calculation ◽  
Dimensional Flow ◽  
Flow Through

The extension of a well established three dimensional flow calculation method to calculate the flow through multiple turbomachinery blade rows is described in this paper. To avoid calculating the unsteady flow, which is inherent in any machine containing both rotating and stationary blade rows, a mixing process is modelled at a calculating station between adjacent blade rows. The effects of this mixing on the flow within the blade rows may be minimised by using extrapolated boundary conditions at the mixing plane.

Long-term thermal two- and three-dimensional analysis of roller compacted concrete dams supported by monitoring verification

2010 ◽  
Vol 37 (4) ◽  
pp. 600-610 ◽  
Author(s):  
Vladan Kuzmanovic ◽  
Ljubodrag Savic ◽  
John Stefanakos
Keyword(s):  
Thermal Analysis ◽  
Boundary Conditions ◽  
Thermal Field ◽  
Numerical Models ◽  
Three Dimensional ◽  
Roller Compacted Concrete ◽  
Rcc Dam ◽  
Field Investigations ◽  
Good Agreement

This paper presents two-dimensional (2D) and three-dimensional (3D) numerical models for unsteady phased thermal analysis of RCC dams. The time evolution of a thermal field has been modeled using the actual dam shape, RCC technology and the adequate description of material properties. Model calibration and verification has been done based on the field investigations of the Platanovryssi dam, the highest RCC dam in Europe. The results of a long-term thermal analysis, with actual initial and boundary conditions, have shown a good agreement with the observed temperatures. The influence of relevant parameters on the thermal field of RCC dams has been analyzed. It is concluded that the 2D model is appropriate for the thermal phased analysis, and that the boundary conditions and the mixture properties are the most influential on the RCC dam thermal behavior.

scholarly journals Prediction of Dynamic Stability Using Mapped Chebyshev Pseudospectral Method

2018 ◽  
Vol 2018 ◽  
pp. 1-14 ◽  
Author(s):  
Jae-Young Choi ◽  
Dong Kyun Im ◽  
Jangho Park ◽  
Seongim Choi
Keyword(s):  
Unsteady Flow ◽  
Three Dimensional ◽  
Pseudospectral Method ◽  
Accurate Method ◽  
Spectral Approach ◽  
Fourier Pseudospectral Method ◽  
Chebyshev Pseudospectral Method ◽  
Fourier Pseudospectral ◽  
Chebyshev Pseudospectral ◽  
Good Agreement

A mapped Chebyshev pseudospectral method is extended to solve three-dimensional unsteady flow problems. As the classical Chebyshev spectral approach can lead to numerical instabilities due to ill conditioning of the spectral matrix, the Chebyshev points are evenly redistributed over the domain by an inverse sine mapping function. The mapped Chebyshev pseudospectral method can be used as an alternative time-spectral approach that uses a Chebyshev collocation operator to approximate the time derivative terms in the unsteady flow governing equations, and the method can make general applications to both nonperiodic and periodic problems. In this study, the mapped Chebyshev pseudospectral method is employed to solve three-dimensional periodic problem to verify the spectral accuracy and computational efficiency with those of the Fourier pseudospectral method and the time-accurate method. The results show a good agreement with both of the Fourier pseudospectral method and the time-accurate method. The flow solutions also demonstrate a good agreement with the experimental data. Similar to the Fourier pseudospectral method, the mapped Chebyshev pseudospectral method approximates the unsteady flow solutions with a precise accuracy at a considerably effective computational cost compared to the conventional time-accurate method.

Numerical and Experimental Evaluation of Turbulent Flow in Volute

2003 ◽  
Author(s):  
Akitomo Igarashi ◽  
Kazuyuki Toda ◽  
Makoto Yamamoto ◽  
Toshimichi Sakai
Keyword(s):  
Numerical Simulation ◽  
Cross Section ◽  
Three Dimensional ◽  
Experimental Result ◽  
Centrifugal Fan ◽  
Flow Conditions ◽  
Flow Angle ◽  
Fan Performance ◽  
Centrifugal Fans ◽  
Good Agreement

The performance of centrifugal fans is considerably influenced by the design of tongue at the re-circulation port. The flow in the volute of a centrifugal fan was studied both experimentally and numerically. In this experiment, flow angle, pressure and velocity profiles were measured at a large number of locations in the volute. The flow field in the volute passage was analyzed using Computational Fluid Dynamics. The flow was assumed to be three dimensional, turbulent and steady. The numerical simulation produced qualitatively good agreement with the experimental result. The results from experiment and numerical simulation indicated that the adoption of a re-circulating flow port improved fan performance for all flow conditions. In addition, the existence of strong secondary flow was apparent at the cross-section of the volute passage.

Unsteady Flow at the Outlet of the High Specific Speed Centrifugal Compressor Impeller

1984 ◽  
Author(s):  
Fumikata Kano ◽  
Takafumi Shirakami
Keyword(s):  
Unsteady Flow ◽  
Centrifugal Compressor ◽  
Coal Gasification ◽  
Three Dimensional ◽  
Axial Direction ◽  
Navier Stokes ◽  
Meridional Plane ◽  
Mixed Flow ◽  
Navier Stokes Equation ◽  
Specific Speed

The unsteady flow at the outlet of the high specific speed mixed flow Impeller was studied. The specific speed is 500 (m3/min)1/2 · rpm · m−3/4. The flow is strongly influenced by the impeller blading. The other hand, the flow influences the performance of the stationary vanes downstream of the impeller. The flow path at the outlet of the mixed flow impeller is inclined to the axial direction and is curved in the meridional plane. The study was carried out to develop the 30 MW centrifugal compressor. This compressor is used in the field of the coal gasification, the geothermal power generation, etc. The distributions of flow velocity, pressure and temperature of three dimensional flow were measured using a high sensitive pressure transducer and a total temperature probe. The flow was surveyed across the entire passage at about ten axial locations including endwall boundary layer. A theoretical analysis was also carried out using the linearized Navier-Stokes equation.

Three-dimensional Numerical Simulation of Disk Rotating Detonation Engine; Unsteady Flow Structure

2019 ◽  
Author(s):  
Tomohiro Watanabe ◽  
Nicolas H. Jourdaine ◽  
Nobuyuki Tsuboi ◽  
Takayuki Kojima ◽  
Koichi A. Hayashi
Keyword(s):  
Numerical Simulation ◽  
Unsteady Flow ◽  
Flow Structure ◽  
Three Dimensional ◽  
Rotating Detonation Engine ◽  
Detonation Engine ◽  
Rotating Detonation

Numerical Model of Three-Dimensional Motion of Plate-Type Wind-Borne Debris Based on Quaternions and its Improvement in Unsteady Flow

2013 ◽  
Vol 405-408 ◽  
pp. 2399-2408 ◽  
Author(s):  
An Min Fu ◽  
Peng Huang ◽  
Ming Gu
Keyword(s):  
Numerical Model ◽  
Unsteady Flow ◽  
Three Dimensional ◽  
Two Dimensional ◽  
Moment Coefficient ◽  
Flight Mode ◽  
Gimbal Lock ◽  
Improved Model ◽  
Plate Type ◽  
Good Agreement

A numerical model of three-dimensional motion of plate-type wind-borne debris in uniform wind field based on quaternions is proposed in this paper. This model can simulate the complex 3D spinning flight robustly and efficiently with rotational quaternions, which are also free from the gimbal lock that is associated with Euler rotational matrix. The predictions from the model were then compared with the results of another quasi-steady model, and good agreement is found. For the unsteady flow involved in autorotational flight mode, the present model was improved by revising the damping moment in order to simulate the two-dimensional motion of plates with higher accuracy. Calibration of the damping moment coefficient was performed through a direct comparison of the predicted non-dimensional angular velocity with the results of CFD-RBD model. The predictions of the improved model agree reasonably well with the CFD-RBD results, which verifies the accuracy of the improved model in predicting the two-dimensional trajectories of plates.

Numerical Simulation of Synthetic Heat Transfer in Laminar Nanofluid in a Horizontal Pipe

2014 ◽  
Vol 936 ◽  
pp. 409-414
Author(s):  
Mohsen Mirzaei ◽  
Mostafa Jafari Gishin ◽  
Mohammad Abbaspour
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Convective Heat Transfer Coefficient ◽  
Three Dimensional ◽  
Oxide Nanoparticles ◽  
Aluminum Oxide Nanoparticles ◽  
Horizontal Pipe ◽  
Water Based ◽  
Solid Liquid ◽  
Good Agreement

In this study, the effect of solid-liquid volumetric ratio in laminar flow of nanofluid has been investigated numerically. The conservation equations are utilized in three dimensional elliptical forms for laminar and steady flow, and the effects of adding aluminum oxide nanoparticles to water based-fluid are studied. First, the influence of solid-liquid volumetric ratio on the secondary flow vortices, non-dimensional temperature is investigated for a flow with a fixed low Reynolds number and different Grashof numbers in a horizontal pipe. Then, the effect of variation in solid-liquid volumetric ratio on Nusselt number and convective heat transfer coefficient along the pipe is studied. The results of this study are in good agreement with the current literatures.

Sign in / Sign up

Export Citation Format

Share Document