Study on the Vibrational Characteristics of a Tube Array Caused by Two-Phase Flow—Part 1: Random Vibration

1992 ◽  
Vol 114 (4) ◽  
pp. 472-478 ◽  
Author(s):  
T. Nakamura ◽  
K. Fujita ◽  
K. Kawanishi ◽  
N. Yamaguchi ◽  
A. Tsuge
Keyword(s):  
Random Vibration ◽  
Two Phase Flow ◽  
Impact Force ◽  
Phase Flow ◽  
Liquid Slug ◽  
Flow Induced Vibration ◽  
Two Phase ◽  
Vibrational Characteristics ◽  
Flow Part ◽  
The Impact

There are few published papers about the flow-induced vibration caused by two-phase flow. Especially, the experimental data at high-pressure and high-temperature conditions which corresponds to the practical phenomenon, are extremely few, and the mechanism of the two-phase flow-induced load acting on a tube in tube array has not yet been explained. This paper shows the experimental results about the turbulent buffeting force both by air-water two-phase flow and by steam-water flow of extreme conditions up to 5.8 MPa in pressure and 272°C in temperature, the explanation of the mechanism of this force, and the method to evaluate the response of the tube caused by two-phase flow. Here, the main source of the buffeting force by two-phase flow in slug or froth flow pattern is recognized to be the impact force caused by the intermittently rising liquid slug. The slug speed and the fluid force acting on a tube are estimated, combined with the estimation of the intermittence of the occurrence of the liquid slug rising.

Study on the Vibrational Characteristics of a Tube Array Caused by Two-Phase Flow. Part I: Random Vibration

1995 ◽  
Vol 9 (5) ◽  
pp. 519-538 ◽  
Author(s):  
T. Nakamura ◽  
K. Fujita ◽  
K. Kawanishi ◽  
N. Yamaguchi ◽  
A. Tsuge
Keyword(s):  
Random Vibration ◽  
Two Phase Flow ◽  
Phase Flow ◽  
Two Phase ◽  
Vibrational Characteristics ◽  
Flow Part

Study on the Vibrational Characteristics of a Tube Array Caused by Two-Phase Flow. Part II: Fluidelastic Vibration

1995 ◽  
Vol 9 (5) ◽  
pp. 539-562 ◽  
Author(s):  
T. Nakamura ◽  
K. Fujita ◽  
K. Kawanishi ◽  
N. Yamaguchi ◽  
A. Tsuge
Keyword(s):  
Two Phase Flow ◽  
Phase Flow ◽  
Two Phase ◽  
Vibrational Characteristics ◽  
Flow Part

New Experimental Data and Analysis for Two-Phase Flow-Induced Vibration of Tube Bundles: Preliminary Results

2003 ◽  
Author(s):  
Deepanjan Mitra ◽  
Vijay K. Dhir ◽  
Ivan Catton
Keyword(s):  
Two Phase Flow ◽  
Structural Parameters ◽  
Cross Flow ◽  
Instability Criterion ◽  
Phase Flow ◽  
Flow Induced Vibration ◽  
Two Phase ◽  
Void Fractions ◽  
Comparison Of The Results ◽  
Square Array

In the past, fluid-elastic instability in two-phase flow has been largely investigated with air-water flow. In this work, new experiments are conducted in air-water cross-flow with a fully flexible 5 × 3 normal square array having pitch-to-diameter ratio of 1.4. The tubes have a diameter of 0.016 m and a length of 0.21 m. The vibrations are measured using strain gages installed on piano wires used to suspend the tubes. Experiments are carried out for void fractions from 0%–30%. A comparison of the results of the current tests with previous experiments conducted in air-water cross-flow shows that instability occurs earlier in a fully flexible array as compared to a flexible tube surrounded by rigid tubes in an array. An attempt is made to separate out the effects of structural parameters of three different experimental datasets by replotting the instability criterion by incorporating the instability constant K, in the reduced velocity parameter.

Solid–liquid two-phase flow and erosion calculation of butterfly valves at small opening based on DEM method

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Benliang Xu ◽  
Zuchao Zhu ◽  
Zhe Lin ◽  
Dongrui Wang
Keyword(s):  
Peer Review ◽  
Two Phase Flow ◽  
Solid Particles ◽  
Phase Flow ◽  
Butterfly Valve ◽  
Two Phase ◽  
Content Type ◽  
Small Opening ◽  
Solid Liquid ◽  
The Impact

Purpose The study aims to decrease the effect of solid particles on a butterfly valve, which will cause seal failure and leakage, providing a reference for anti-wear design. Design/methodology/approach In this paper, computational fluid dynamics discrete element method (CFD-DEM) simulation was conducted to study the solid–liquid two-phase flow characteristics and erosion characteristics of a butterfly valve with a different opening. Findings Abrasion at 10% opening is affected by high-speed jets in upper and lower parts of the pipeline, where the erosion is intense. The impact of the jet on the upper part of 20% opening begins to weaken. With the top backflow vortex disappearing, the effect of lower jet is enhanced. Meanwhile, the bottom backflow vortex phenomenon is obvious, and the abrasion position moves downward. At 30% opening, the velocity is further weakened, and the circulation effect of lower flow channel is more obvious than that of the upper one. Originality/value It is the first time to use DEM to investigate the two-phase flow and erosion characteristics at a small opening of a butterfly valve, considering the effect of inter-particle collision. Therefore, this study carries on the thorough analysis and discussion. At the same opening degree, with increasing of the particle size, the abrasion of valve frontal surface increases when the size is less than 150 µm and decreases when it is greater than 150 µm. For the valve backflow surface, this boundary value becomes 200 µm. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-07-2020-0264/

Numerical and experimental investigation on the effect of the two-phase flow pattern on heat transfer of piston cooling gallery

2019 ◽  
Vol 20 (5) ◽  
pp. 507 ◽  
Author(s):  
Lijun Deng ◽  
Jian Zhang ◽  
Guannan Hao ◽  
Jing Liu
Keyword(s):  
Heat Transfer ◽  
Flow Pattern ◽  
Two Phase Flow ◽  
Unstable Wave ◽  
Fluid Viscosity ◽  
Phase Flow ◽  
Two Phase ◽  
Flow Process ◽  
The Impact ◽  
Piston Cooling

To study factors affecting the formation and conversion of two-phase flow pattern as well as the heat transfer of piston cooling gallery, a transient visual target test bench was set up to research the oscillatory flow characteristics in the cooling gallery under idle condition of the engine. The computational fluid dynamics (CFD) was employed while dynamic mesh technology, SST k–ω turbulence model and volume of fluid (VOF) two-phase flow model were applied to simulate the flow process of piston cooling gallery so as to predict the distribution pattern of two-phase flow. Simulation results were in good agreement with that experimentally obtained. It was observed that in the reciprocating movement of the piston, the action of two-phase flow oscillation was severe, forming some unstable wave flows and slug flows. Results show that under the same pipe diameter, the increase of fluid viscosity results in the decrease of amplitude and the increase of the liquid slugs number as well as the enhancement on heat transfer effect. In addition, it was revealed that injection pressure has little effect on the two-phase flow pattern. However, when the pressure is reduced, the change of the liquid phase is weakened and the locations of flow pattern transition move towards to the behind, thus the impact on the heat transfer is also faint.

Analysis of Flow-Induced Vibration Due to Stratified Wavy Two-Phase Flow

2016 ◽  
Vol 138 (9) ◽  
Author(s):  
Shuichiro Miwa ◽  
Takashi Hibiki ◽  
Michitsugu Mori
Keyword(s):  
Two Phase Flow ◽  
Dynamic Properties ◽  
Fluid Model ◽  
Dominant Frequency ◽  
Phase Flow ◽  
Flow Induced Vibration ◽  
Two Phase ◽  
Pipe Bend ◽  
Experimental Database ◽  
Force Fluctuation

Fluctuating force induced by horizontal gas–liquid two-phase flow on 90 deg pipe bend at atmospheric pressure condition is considered. Analysis was conducted to develop a model which is capable of predicting the peak force fluctuation frequency and magnitudes, particularly at the stratified wavy two-phase flow regime. The proposed model was developed from the local instantaneous two-fluid model, and adopting guided acoustic theory and dynamic properties of one-dimensional (1D) waves to consider the collisional force due to the interaction between dynamic waves and structure. Comparing the developed model with experimental database, it was found that the main contribution of the force fluctuation due to stratified wavy flow is from the momentum and pressure fluctuations, and collisional effects. The collisional effect is due to the fluid–solid interaction of dynamic wave, which is named as the wave collision force. Newly developed model is capable of predicting the force fluctuations and dominant frequency range with satisfactory accuracy for the flow induced vibration (FIV) caused by stratified wavy two-phase flow in 52.5 mm inner diameter (ID) pipe bend.

Sign in / Sign up

Export Citation Format

Share Document