Laminar-To-Turbulent Transition on a Body of Revolution With an Extended Favorable Pressure Gradient Forebody

1984 ◽  
Vol 106 (2) ◽  
pp. 202-210 ◽  
Author(s):  
R. J. Hansen ◽  
J. G. Hoyt
Keyword(s):  
Boundary Layer ◽  
Pressure Gradient ◽  
The Body ◽  
Boundary Layer Transition ◽  
Single Element ◽  
Body Of Revolution ◽  
Laminar To Turbulent Transition ◽  
Turbulent Transition ◽  
Roughness Elements ◽  
Favorable Pressure Gradient

An experimental study of the laminar-to-turbulent transition and resulting hydrodynamic forces on a body of revolution with a long, favorable pressure gradient forebody (i.e., where pressure is dropping and the flow accelerating) is reported. Over a substantial range of body velocity and angle of attack the favorable pressure gradient is shown to postpone transition to the point of laminar separation, and this extended laminar region results in a much lower hydrodynamic drag than is characteristic of an all-turbulent body. The intermittency of the boundary layer and the propagation characteristics of turbulent spots in the extended favorable pressure gradient region are quantified by hot film probes mounted flush with the body surface. The sensitivity of the boundary layer transition to three-dimensional surface roughness elements located in tandem (along a streamline) is also quantified. A number of such elements in tandem causes transition at a lower Reynolds number than would a single element of the same size, this effect becoming more pronounced with increasing number of roughness elements and decreasing space between them.

Investigation of the Laminar-Turbulent Transition of Boundary Layers Disturbed by Wakes

1982 ◽  
Author(s):  
H. Pfeil ◽  
R. Herbst ◽  
T. Schröder
Keyword(s):  
Boundary Layer ◽  
Pressure Gradient ◽  
Boundary Layers ◽  
Transition Process ◽  
Boundary Layer Transition ◽  
Layer Transition ◽  
Turbulent Spots ◽  
Turbulent Transition ◽  
Time Space ◽  
Favorable Pressure Gradient

The boundary layer transition under instationary afflux conditions as present in the stages of turbomachines is investigated. A model for the transition process is introduced by means of time-space distributions of the turbulent spots during transition and schematic drawings of the instantaneous boundary layer thicknesses. To confirm this model, measurements of the transition with zero and favorable pressure gradient are performed.

Investigation of the Laminar-Turbulent Transition of Boundary Layers Disturbed by Wakes

1983 ◽  
Vol 105 (1) ◽  
pp. 130-137 ◽  
Author(s):  
H. Pfeil ◽  
R. Herbst ◽  
T. Schro¨der
Keyword(s):  
Boundary Layer ◽  
Pressure Gradient ◽  
Boundary Layers ◽  
Transition Process ◽  
Boundary Layer Transition ◽  
Layer Transition ◽  
Turbulent Spots ◽  
Turbulent Transition ◽  
Time Space ◽  
Favorable Pressure Gradient

The boundary layer transition under instationary afflux conditions as present in the stages of turbomachines is investigated. A model for the transition process is introduced by means of time-space distributions of the turbulent spots during transition and schematic drawings of the instantaneous boundary layer thicknesses. To confirm this model, measurements of the transition with zero and favorable pressure gradient are performed.

scholarly journals Studies on Wake-Disturbed Boundary Layers Under the Influences of Favorable Pressure Gradient and Free-Stream Turbulence: Part I — Experimetal Setup and Discussions on Transition Model

1997 ◽  
Author(s):  
Ken-ichi Funazaki ◽  
Takashi Kitazawa ◽  
Kazuyuki Koizumi ◽  
Tadashi Tanuma
Keyword(s):  
Boundary Layer ◽  
Pressure Gradient ◽  
Boundary Layers ◽  
Free Stream ◽  
Boundary Layer Transition ◽  
Test Model ◽  
Flat Plates ◽  
Layer Transition ◽  
Free Stream Turbulence ◽  
Favorable Pressure Gradient

The objective of this study is to investigate effects of favorable pressure gradient as well as free-stream turbulence upon wake-induced boundary layer transition on a flat plate. Likewise in the previous study by Funazaki (1996), a spoked-wheel type wake generator is employed in this study. Two identical flat plates with sharp edge are used as test model. One of them is for measurement of boundary layers over the test plate by use of a single hot-wire probe, and the other is provided with thin stainless-steel foils on the surface to measure wake-affected heat transfer along the surface. Free-stream turbulence intensities are controlled with several types of turbulence grids. Pressure gradients over the test surface are adjusted by changing an inclination angle of the plate located opposite to the test model. In Part I, transition models proposed by Mayle and Dullenkopf (1990b) and Funazaki (1996a, 1996b) are compared with the experimental data obtained in this study to examine how such a model succeeds or fails in predicting the wake-induced boundary layer transition under the influences of favorable pressure gradient with a low free-stream turbulence.

The flow structure in the lee of an inclined 6:1 prolate spheroid

1994 ◽  
Vol 269 ◽  
pp. 79-106 ◽  
Author(s):  
T. C. Fu ◽  
A. Shekarriz ◽  
J. Katz ◽  
T. T. Huang
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Flow Structure ◽  
Incidence Angle ◽  
Prolate Spheroid ◽  
The Body ◽  
Boundary Layer Transition ◽  
Primary Vortex ◽  
Vortex Sheets ◽  
Vorticity Distribution

Particle displacement velocimetry is used to measure the velocity and vorticity distributions around an inclined 6: 1 prolate spheroid. The objective is to determine the effects of boundary-layer tripping, incidence angle, and Reynolds number on the flow structure. The vorticity distributions are also used for computing the lateral forces and rolling moments that occur when the flow is asymmetric. The computed forces agree with results of direct measurements. It is shown that when the flow is not tripped, separation causes the formation of a pair of vortex sheets. The size of these sheets increases with increasing incidence angle and axial location. Their orientation and internal vorticity distribution also depend on incidence. Rollup into distinct vortices occurs in some cases, and the primary vortex contains between 20 % and 50 % of the overall circulation. The entire flow is unsteady and there are considerable variations in the instantaneous vorticity distributions. The remainder of the lee side, excluding these vortex sheets, remains almost vorticity free, providing clear evidence that the flow can be characterized as open separation. Boundary-layer tripping causes earlier separation on part of the model, brings the primary vortex closer to the body, and spreads the vorticity over a larger region. The increased variability in the vorticity distribution causes considerable force fluctuations, but the mean loads remain unchanged. Trends with increasing Reynolds number are conflicting, probably because of boundary-layer transition. The separation point moves towards the leeward meridian and the normal force decreases when the Reynolds number is increased from 0.42 × 106 to 1.3 × 106. Further increase in the Reynolds number to 2.1 × 106 and tripping cause an increase in forces and earlier separation.

The Effect of Real Turbine Roughness With Pressure Gradient on Heat Transfer

2003 ◽  
Author(s):  
Jeffrey P. Bons ◽  
Stephen T. McClain
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Pressure Gradient ◽  
Adverse Pressure Gradient ◽  
Combined Effects ◽  
Pressure Gradients ◽  
Smooth Wall ◽  
Reynolds Analogy ◽  
Integral Boundary ◽  
Favorable Pressure Gradient

Experimental measurements of heat transfer (St) are reported for low speed flow over scaled turbine roughness models at three different freestream pressure gradients: adverse, zero (nominally), and favorable. The roughness models were scaled from surface measurements taken on actual, in-service land-based turbine hardware and include samples of fuel deposits, TBC spallation, erosion, and pitting as well as a smooth control surface. All St measurements were made in a developing turbulent boundary layer at the same value of Reynolds number (Rex≅900,000). An integral boundary layer method used to estimate cf for the smooth wall cases allowed the calculation of the Reynolds analogy (2St/cf). Results indicate that for a smooth wall, Reynolds analogy varies appreciably with pressure gradient. Smooth surface heat transfer is considerably less sensitive to pressure gradients than skin friction. For the rough surfaces with adverse pressure gradient, St is less sensitive to roughness than with zero or favorable pressure gradient. Roughness-induced Stanton number increases at zero pressure gradient range from 16–44% (depending on roughness type), while increases with adverse pressure gradient are 7% less on average for the same roughness type. Hot-wire measurements show a corresponding drop in roughness-induced momentum deficit and streamwise turbulent kinetic energy generation in the adverse pressure gradient boundary layer compared with the other pressure gradient conditions. The combined effects of roughness and pressure gradient are different than their individual effects added together. Specifically, for adverse pressure gradient the combined effect on heat transfer is 9% less than that estimated by adding their separate effects. For favorable pressure gradient, the additive estimate is 6% lower than the result with combined effects. Identical measurements on a “simulated” roughness surface composed of cones in an ordered array show a behavior unlike that of the scaled “real” roughness models. St calculations made using a discrete-element roughness model show promising agreement with the experimental data. Predictions and data combine to underline the importance of accounting for pressure gradient and surface roughness effects simultaneously rather than independently for accurate performance calculations in turbines.

Infrared thermography of hypersonic boundary layer transition induced by isolated roughness elements

2021 ◽  
Author(s):  
Shicheng Liu ◽  
Meng Wang ◽  
Hao Dong ◽  
Tianyu Xia ◽  
Lin Chen ◽  
...  
Keyword(s):  
Boundary Layer ◽  
Infrared Thermography ◽  
Roughness Element ◽  
Transition Process ◽  
Boundary Layer Transition ◽  
Hypersonic Boundary Layer ◽  
Layer Transition ◽  
Leading Role ◽  
Roughness Elements ◽  
Element Shape

Roughness element induced hypersonic boundary layer transition on a flat plate is investigated using infrared thermography at Ma = 5 and 6 flow condition. Surface Stanton number is acquired to analyze the effect of roughness element shape and height on the transition process. The correlation between the vortex structure induced by roughness element and the wall heat streaks is established. The results indicate that higher roughness element would induce stronger streamwise heat flux streaks, lead to transition advance in streamwise centerline and increase the width of spanwise wake. Moreover, for low roughness element, the effect of the shape is not obvious, and the height plays a leading role in the transition; for tall roughness element, the effect on accelerating transition for the diamond roughness element is the best, the square is the worst, and the shape plays a leading role in the transition.

A Note on the Resistance of Bodies of Revolution and Ship Forms

1974 ◽  
Vol 18 (03) ◽  
pp. 153-168
Author(s):  
N. Matheson ◽  
P. N. Joubert
Keyword(s):  
Boundary Layer ◽  
Reasonable Agreement ◽  
The Body ◽  
Experimental Results ◽  
Body Of Revolution ◽  
Bodies Of Revolution ◽  
Boundary Layer Development ◽  
Layer Development

A simple so-called 'equivalent' body of revolution is proposed for reflex ship forms in an attempt to simplify calculation of the boundary layer over a ship's hull when there is no wavemaking. How­ever, exhaustive testing of one body of revolution did not produce a favorable comparison with re­sults for the corresponding reflex model. Gadd's recently proposed theory was used to calculate the boundary-layer development over the body of revolution. Reasonable agreement was obtained between the calculated and experimental results.

scholarly journals Influence of two-dimensional roughness element on boundary layer structure in the favourable pressure gradient region of the swept wing

2019 ◽  
Vol 234 (1) ◽  
pp. 20-27
Author(s):  
Stepan Tolkachev ◽  
Victor Kozlov ◽  
Valeriya Kaprilevskaya
Keyword(s):  
Boundary Layer ◽  
Pressure Gradient ◽  
Layer Structure ◽  
Roughness Element ◽  
Three Dimensional ◽  
Two Dimensional ◽  
Frequency Range ◽  
Swept Wing ◽  
Boundary Layer Structure ◽  
Roughness Elements

In this article, the results of research about stationary and secondary disturbances development behind the localized and two-dimensional roughness elements are presented. It is shown that the two-dimensional roughness element has a destabilizing effect on the disturbances induced by the three-dimensional roughness element lying upstream. In this case, the two-dimensional roughness element causes the appearance of stationary structures, and then secondary perturbations, whose frequency range lies lower than in the case of the stationary vortices excited by a three-dimensional roughness element.

Sign in / Sign up

Export Citation Format

Share Document