Verification of Predicted Knee Replacement Kinematics During Simulated Gait in the Kansas Knee Simulator

2010 ◽  
Vol 132 (8) ◽  
Author(s):  
Jason P. Halloran ◽  
Chadd W. Clary ◽  
Lorin P. Maletsky ◽  
Mark Taylor ◽  
Anthony J. Petrella ◽  
...  
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Knee Replacement ◽  
Degrees Of Freedom ◽  
Computational Models ◽  
Evaluation Process ◽  
Element Model ◽  
Explicit Finite Element ◽  
Knee Simulator ◽  
Flexion Extension

Evaluating total knee replacement kinematics and contact pressure distributions is an important element of preclinical assessment of implant designs. Although physical testing is essential in the evaluation process, validated computational models can augment these experiments and efficiently evaluate perturbations of the design or surgical variables. The objective of the present study was to perform an initial kinematic verification of a dynamic finite element model of the Kansas knee simulator by comparing predicted tibio- and patellofemoral kinematics with experimental measurements during force-controlled gait simulation. A current semiconstrained, cruciate-retaining, fixed-bearing implant mounted in aluminum fixtures was utilized. An explicit finite element model of the simulator was developed from measured physical properties of the machine, and loading conditions were created from the measured experimental feedback data. The explicit finite element model allows both rigid body and fully deformable solutions to be chosen based on the application of interest. Six degrees-of-freedom kinematics were compared for both tibio- and patellofemoral joints during gait loading, with an average root mean square (rms) translational error of 1.1 mm and rotational rms error of 1.3 deg. Model sensitivity to interface friction and damping present in the experimental joints was also evaluated and served as a secondary goal of this paper. Modifying the metal-polyethylene coefficient of friction from 0.1 to 0.01 varied the patellar flexion-extension and tibiofemoral anterior-posterior predictions by 7 deg and 2 mm, respectively, while other kinematic outputs were largely insensitive.

Finite Element Model of the Human Knee Joint to Study Tibio-Femoral Contact Mechanics

2000 ◽  
Author(s):  
Tammy Haut Donahue ◽  
Maury L. Hull ◽  
Mark M. Rashid ◽  
Christopher R. Jacobs
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Degrees Of Freedom ◽  
Soft Tissues ◽  
Element Model ◽  
Human Knee ◽  
Human Knee Joint ◽  
Solid Models ◽  
Flexion Extension ◽  
A New Technique

Abstract A finite element model of the tibio-femoral joint in the human knee was created using a new technique for developing accurate solid models of soft tissues (i.e. cartilage and menisci). The model was used to demonstrate that constraining rotational degrees of freedom other than flexion/extension when the joint is loaded in compression markedly affects the load distribution between the medial and lateral sides of the joint. The model also was used to validate the assumption that the bones can be treated as rigid.

Experimental Validation of a Finite-Element Model to Simulate an Impact on Pipeline due to Vehicles or Heavy Object Fall

2016 ◽  
Author(s):  
Charles Fernandez ◽  
Maxime Bertin ◽  
Philippe Cardin
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Computational Models ◽  
Element Model ◽  
Material Behavior ◽  
Third Party ◽  
Experimental Program ◽  
External Diameter ◽  
Explicit Finite Element ◽  
Excavator Tooth

This paper deals in a first part with an experimental program aimed at studying mechanical impacts on pipelines. Tests have been performed at CRIGEN-ENGIE-LAB, the Center of Research and Innovation for Gas and New Energies of ENGIE (previously GDF SUEZ) on pipes under pressure and pipes without internal pressure with an impact tool whom length is greater than the external diameter of the pipes and a tool similar to an excavator tooth. In a first part, the paper presents the tests which show a very good behavior of the pipelines. None have failed for the large impact-tool, which is equivalent in terms of impact energy to a 1000 kg-vehicle impacting a pipeline at ∼32 km.h−1 (∼20 miles.h−1). In a second part, the paper deals with existing analytical solutions: the Det Norske Veritas model for dent assessment and the EPRG model for mechanical damage assessment due to an excavator tooth. Comparisons with the CRIGEN tests show that the DNV equation is not always conservative in terms of predicted rupture energy and that the third-party damage EPRG model predicts correctly the rupture for the tooth-like tool but does not seem adapted for the longer tool. In a third part, an explicit finite-element model (performed with the commercial software Abaqus) has then been used to simulate numerically the tests. Different material behavior laws have been tested: a classical elastic-plastic law and a law with a time-dependence (Cowper-Symonds). The comparison between the final geometry of the impacted pipeline and the computational solution is quite satisfactory. A numerical strain criterion is extrapolated and then applied to some real configurations. This paper presents the tests, the analytical comparisons, the computational models and some applications to the fall of heavy long objects as well as vehicle impact on pipelines.

A finite element model for evaluation of tibial prosthesis-bone interface in total knee replacement

1992 ◽  
Vol 25 (12) ◽  
pp. 1413-1424 ◽  
Author(s):  
R.L. Rakotomanana ◽  
P.F. Leyvraz ◽  
A. Curnier ◽  
J.H. Heegaard ◽  
P.J. Rubin
Keyword(s):  
Finite Element ◽  
Total Knee Replacement ◽  
Finite Element Model ◽  
Knee Replacement ◽  
Element Model ◽  
Bone Interface ◽  
Total Knee

FEBio finite element model of a pediatric cervical spine

2021 ◽  
pp. 1-7
Author(s):  
Sean M. Finley ◽  
J. Harley Astin ◽  
Evan Joyce ◽  
Andrew T. Dailey ◽  
Douglas L. Brockmeyer ◽  
...  
Keyword(s):  
Finite Element ◽  
Cervical Spine ◽  
Finite Element Model ◽  
Material Properties ◽  
Surgical Simulation ◽  
Element Model ◽  
Axial Stiffness ◽  
Published Data ◽  
Axial Tension ◽  
Flexion Extension

OBJECTIVE The underlying biomechanical differences between the pediatric and adult cervical spine are incompletely understood. Computational spine modeling can address that knowledge gap. Using a computational method known as finite element modeling, the authors describe the creation and evaluation of a complete pediatric cervical spine model. METHODS Using a thin-slice CT scan of the cervical spine from a 5-year-old boy, a 3D model was created for finite element analysis. The material properties and boundary and loading conditions were created and model analysis performed using open-source software. Because the precise material properties of the pediatric cervical spine are not known, a published parametric approach of scaling adult properties by 50%, 25%, and 10% was used. Each scaled finite element model (FEM) underwent two types of simulations for pediatric cadaver testing (axial tension and cardinal ranges of motion [ROMs]) to assess axial stiffness, ROM, and facet joint force (FJF). The authors evaluated the axial stiffness and flexion-extension ROM predicted by the model using previously published experimental measurements obtained from pediatric cadaveric tissues. RESULTS In the axial tension simulation, the model with 50% adult ligamentous and annulus material properties predicted an axial stiffness of 49 N/mm, which corresponded with previously published data from similarly aged cadavers (46.1 ± 9.6 N/mm). In the flexion-extension simulation, the same 50% model predicted an ROM that was within the range of the similarly aged cohort of cadavers. The subaxial FJFs predicted by the model in extension, lateral bending, and axial rotation were in the range of 1–4 N and, as expected, tended to increase as the ligament and disc material properties decreased. CONCLUSIONS A pediatric cervical spine FEM was created that accurately predicts axial tension and flexion-extension ROM when ligamentous and annulus material properties are reduced to 50% of published adult properties. This model shows promise for use in surgical simulation procedures and as a normal comparison for disease-specific FEMs.

Finite Element Modeling of Unidirectional Non-Crimp Fabric for Manufacturing of Composites with Embedded Cabling

2013 ◽  
Vol 554-557 ◽  
pp. 484-491 ◽  
Author(s):  
Alexander S. Petrov ◽  
James A. Sherwood ◽  
Konstantine A. Fetfatsidis ◽  
Cynthia J. Mitchell
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Element Model ◽  
Explicit Finite Element ◽  
Shell Elements ◽  
Beam Elements ◽  
Hybrid Finite Element ◽  
International Benchmarking ◽  
Unidirectional Glass ◽  
Forming Simulations

A hybrid finite element discrete mesoscopic approach is used to model the forming of composite parts using a unidirectional glass prepreg non-crimp fabric (NCF). The tensile behavior of the fabric is represented using 1-D beam elements, and the shearing behavior is captured using 2-D shell elements into an ABAQUS/Explicit finite element model via a user-defined material subroutine. The forming of a hemisphere is simulated using a finite element model of the fabric, and the results are compared to a thermostamped part as a demonstration of the capabilities of the used methodology. Forming simulations using a double-dome geometry, which has been used in an international benchmarking program, were then performed with the validated finite element model to explore the ability of the unidirectional fabric to accommodate the presence of interlaminate cabling.

Biomechanical Effect of Lumbar Disc Degeneration Under Flexion/Extension: A Finite Element Model Study

2007 ◽  
Author(s):  
Lissette M. Ruberté ◽  
Raghu Natarajan ◽  
Gunnar B. J. Andersson
Keyword(s):  
Finite Element ◽  
Lumbar Spine ◽  
Finite Element Model ◽  
Disc Degeneration ◽  
Pathological Condition ◽  
Lumbar Disc ◽  
Element Model ◽  
Adjacent Segment ◽  
Lumbar Disc Degeneration ◽  
Flexion Extension

Degenerative disc disease (DDD) is a progressive pathological condition observed in 60 to 80% of the population [1]. It involves changes in both the biochemistry and morphology of the intervertebral disc and is associated with chronic low back pain, sciatica and adult scoliosis [2,3]. The most accepted theory of the effects of DDD on the kinematics of the spine is that proposed by Kirkaldy-Willis and Farfan which states that the condition initiates as a temporary dysfunction, followed by instability and then re-stabilization as the disease progresses [4]. Although there is no clear relationship between disc degeneration and the mechanical behavior of the lumbar spine, abnormal motion patterns either in the form of increased motion or erratic motion have been reported from studies on human cadaveric motion segments [5,6]. To date however no study has looked at how disc degeneration affects the adjacent segment mechanics. IN vivo testing is difficult for these purposes given that specimens are generally obtained from people at the later stages of life and consequently often display multiple pathologies. A finite element model is a viable alternative to study the mechanics of the segments adjacent to the diseased disc. It is hypothesized that moderate degeneration at one level will alter the kinematics of the whole lumbar spine.

Modeling of fast pre-joining processes optimization for skin-stringer panels

2014 ◽  
Vol 34 (4) ◽  
pp. 323-332 ◽  
Author(s):  
Gang Liu ◽  
Wei Tang ◽  
Ying-Lin Ke ◽  
Qing-Liang Chen ◽  
Yunbo Bi
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Degrees Of Freedom ◽  
Traditional Approach ◽  
Element Model ◽  
Optimal Number ◽  
Neighborhood Search ◽  
Adaptive Genetic Algorithm ◽  
Time Saving ◽  
Content Type

Purpose – The purpose of this paper is to propose a new model for optimizing pre-joining processes quickly and accurately, guiding workers to standardized operations. For the automatic riveting in panel assemblies, the traditional approach of determination of pre-joining processes entirely rests on the experience of workers, which leads to the improper number, location and sequence of pre-joining, the low quality stability and the high repair rate in most cases. Design/methodology/approach – The clearances computation with the complete finite element model for every process combination is time-consuming. Therefore a fast pre-joining processes optimization model (FPPOM) is proposed. This model treats both the measured initial clearances and the stiffness matrices of key points of panels as an input; considers the permissive clearances as an evaluation criterion; regards the optimal number, location and sequence as an objective; and takes the neighborhood-search-based adaptive genetic algorithm as a solution. Findings – A comparison between the FPPOM and complete finite element model with clearances (CFEMC) was made in practice. Further, the results indicate that running the FPPOM is time-saving by >90 per cent compared with the CFEMC. Practical implications – This paper provides practical insights into realizing the pre-joining processes optimization quickly. Originality/value – This paper is the first to propose the FPPOM, which could simplify the processes, reduce the degrees of freedom of nodes and conduct the manufacturers to standardized manipulations.

A Three-Dimensional Dynamic Finite Element Model of the Prosthetic Knee Joint: Simulation of Joint Laxity and Kinematics

2005 ◽  
Vol 219 (6) ◽  
pp. 415-424 ◽  
Author(s):  
M Barink ◽  
A van Kampen ◽  
M de Waal Malefijt ◽  
N Verdonschot
Keyword(s):  
Finite Element ◽  
Knee Joint ◽  
Finite Element Model ◽  
Mathematical Formulation ◽  
Three Dimensional ◽  
Element Model ◽  
Joint Kinematics ◽  
Published Data ◽  
Dynamic Finite Element ◽  
Flexion Extension

For testing purposes of prostheses at a preclinical stage, it is very valuable to have a generic modelling tool, which can be used to optimize implant features and to avoid poor designs being launched on to the market. The modelling tool should be fast, efficient, and multipurpose in nature; a finite element model is well suited to the purpose. The question posed in this study was whether it was possible to develop a mathematically fast and stable dynamic finite element model of a knee joint after total knee arthroplasty that would predict data comparable with published data in terms of (a) laxities and ligament behaviour, and (b) joint kinematics. The soft tissue structures were modelled using a relatively simple, but very stable, composite model consisting of a band reinforced with fibres. Ligament recruitment and balancing was tested with laxity simulations. The tibial and patellar kinematics were simulated during flexion-extension. An implicit mathematical formulation was used. Joint kinematics, joint laxities, and ligament recruitment patterns were predicted realistically. The kinematics were very reproducible and stable during consecutive flexion-extension cycles. Hence, the model is suitable for the evaluation of prosthesis design, prosthesis alignment, ligament behaviour, and surgical parameters with respect to the biomechanical behaviour of the knee.

Sign in / Sign up

Export Citation Format

Share Document