Heat Transfer and Pressure Loss in Rectangular One-Side-Ribbed Channels With Different Aspect Ratios

2013 ◽  
Vol 135 (3) ◽  
Author(s):  
Sébastien Kunstmann ◽  
Jens von Wolfersdorf ◽  
Uwe Ruedel
Keyword(s):  
Heat Transfer ◽  
Aspect Ratio ◽  
Heat Transfer Enhancement ◽  
Gas Turbines ◽  
Pressure Loss ◽  
Rectangular Channel ◽  
Channel Height ◽  
Transfer Enhancement ◽  
Height Ratio ◽  
Aspect Ratios

An investigation was conducted to assess the thermal performance of W-shaped, 2W-shaped and 4W-shaped ribs in a rectangular channel. The aspect ratios (W/H) were 2:1, 4:1, and 8:1. The ribs were located on one channel wall. The rib height (e) was kept constant with a rib height-to-hydraulic diameter ratio (e/Dh) of 0.02, 0.03, and 0.06. The rib pitch-to-height ratio (P/e) was 10. The Reynolds numbers investigated (Re > 90 000) are typical for combustor liner cooling configurations of gas turbines. Local heat transfer coefficients using the transient thermochromic liquid crystal technique and overall pressure losses were measured. The rib configurations were investigated numerically to visualize the flow pattern in the channel and to support the understanding of the experimental data. The results show that the highest heat transfer enhancement is obtained by rib configurations with a rib section-to-channel height ratio (Wr/H) of 1:1. W-shaped ribs achieve the highest heat transfer enhancement levels in channels with an aspect ratio of 2:1, 2W-shaped ribs in channels with an aspect ratio of 4:1 and 4W-shaped ribs in channels with an aspect ratio of 8:1. Furthermore, the pressure loss increases with increasing complexity of the rib geometry and blockage ratio.

Heat Transfer and Pressure Loss in Rectangular One-Side-Ribbed Channels With Different Aspect Ratios

2009 ◽  
Author(s):  
Se´bastien Kunstmann ◽  
Jens von Wolfersdorf ◽  
Uwe Ruedel
Keyword(s):  
Heat Transfer ◽  
Aspect Ratio ◽  
Heat Transfer Enhancement ◽  
Gas Turbines ◽  
Pressure Loss ◽  
Rectangular Channel ◽  
Channel Height ◽  
Transfer Enhancement ◽  
Height Ratio ◽  
Aspect Ratios

An investigation was conducted to assess the thermal performance of W-shaped, 2W-shaped and 4W-shaped ribs in a rectangular channel. The aspect ratios (W/H) were 2:1, 4:1 and 8:1. The ribs were located on one channel wall. The rib height (e) was kept constant with a rib height-to-hydraulic diameter ratio (e/Dh) of 0.02, 0.03 and 0.06. The rib pitch-to-height ratio (P/e) was 10. The Reynolds numbers investigated (Re>90,000) are typical for combustor liner cooling configurations of gas turbines. Local heat transfer coefficients using the transient thermochromic liquid crystal technique and overall pressure losses were measured. The rib configurations were investigated numerically to visualize the flow pattern in the channel and to support the understanding of the experimental data. The results show that the highest heat transfer enhancement is obtained by rib configurations with a rib section-to-channel height ratio (Wr/H) of 1:1. W-shaped ribs achieve the highest heat transfer enhancement levels in channels with an aspect ratio of 2:1, 2W-shaped ribs in channels with an aspect ratio of 4:1 and 4W-shaped ribs in channels with an aspect ratio of 8:1. Furthermore, the pressure loss increases with increasing complexity of the rib geometry and blockage ratio.

An Experimental and Numerical Study of Heat Transfer and Pressure Loss in a Rectangular Channel With V-Shaped Ribs

2006 ◽  
Author(s):  
Michael Maurer ◽  
Jens von Wolfersdorf ◽  
Michael Gritsch
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Thermal Performance ◽  
Pressure Loss ◽  
Numerical Study ◽  
Rectangular Channel ◽  
Reynolds Numbers ◽  
Transfer Enhancement ◽  
High Reynolds Numbers ◽  
High Reynolds

An experimental and numerical study was conducted to determine the thermal performance of V-shaped ribs in a rectangular channel with an aspect ratio of 2:1. Local heat transfer coefficients were measured using the steady state thermochromic liquid crystal technique. Periodic pressure losses were obtained with pressure taps along the smooth channel sidewall. Reynolds numbers from 95,000 to 500,000 were investigated with V-shaped ribs located on one side or on both sides of the test channel. The rib height-to-hydraulic diameter ratios (e/Dh) were 0.0625 and 0.02, and the rib pitch-to-height ratio (P/e) was 10. In addition, all test cases were investigated numerically. The commercial software FLUENT™ was used with a two-layer k-ε turbulence model. Numerically and experimentally obtained data were compared. It was determined that the heat transfer enhancement based on the heat transfer of a smooth wall levels off for Reynolds numbers over 200,000. The introduction of a second ribbed sidewall slightly increased the heat transfer enhancement whereas the pressure penalty was approximately doubled. Diminishing the rib height at high Reynolds numbers had the disadvantage of a slightly decreased heat transfer enhancement, but benefits in a significantly reduced pressure loss. At high Reynolds numbers small-scale ribs in a one-sided ribbed channel were shown to have the best thermal performance.

Effect of Rib Spacing on Heat Transfer in a Two-Pass Rectangular Channel (AR=1:4) With a Sharp Entrance at High Rotation Numbers

2008 ◽  
Author(s):  
Michael Huh ◽  
Yao-Hsien Liu ◽  
Je-Chin Han ◽  
Sanjay Chopra
Keyword(s):  
Heat Transfer ◽  
Aspect Ratio ◽  
Heat Transfer Enhancement ◽  
Rotation Number ◽  
Rectangular Channel ◽  
Transfer Enhancement ◽  
Sharp Bend ◽  
Buoyancy Parameter ◽  
First Pass ◽  
Rib Turbulators

The focus of the current study was to determine the effects of rib spacing on heat transfer in rotating 1:4 AR channels. In the current study, heat transfer experiments were performed in a two-pass, 1:4 aspect ratio channel, with a sharp bend entrance. The channel leading and trailing walls in the first pass and second pass utilized angled rib turbulators (45° to the mainstream flow). The rib height-to-hydraulic diameter ratio (e/Dh) was held constant at 0.078. The channel was oriented 90° to the direction of rotation. Three rib pitch-to-rib height ratios (P/e) were studied: P/e = 2.5, 5, and 10. Each ratio was tested at five Reynolds numbers: 10K, 15K, 20K, 30K and 40K. For each Reynolds number, experiments were conducted at five rotational speeds: 0, 100, 200, 300, and 400 rpm. Results showed that the sharp bend entrance has a significant effect on the first pass heat transfer enhancement. In the second pass, the rib spacing and rotation effect are reduced. The P/e = 10 case had the highest heat transfer enhancement based on total area, whereas the P/e = 2.5 had the highest heat transfer enhancement based on the projected area. The current study has extended the range of the rotation number (Ro) and local buoyancy parameter (Box) for a ribbed 1:4 aspect ratio channel up to 0.65 and 1.5, respectively. Correlations for predicting heat transfer enhancement, due to rotation, in the ribbed (P/e = 2.5, 5, and 10) 1:4 aspect ratio channel, based on the extended range of the rotation number and buoyancy parameter, are presented in the paper.

Effect of 45-Deg Rib Orientations on Heat Transfer in a Rotating Two-Pass Channel With Aspect Ratio From 4:1 to 2:1

2019 ◽  
Author(s):  
Izzet Sahin ◽  
Andrew F. Chen ◽  
Chao-Cheng Shiau ◽  
Je-Chin Han ◽  
Robert Krewinkel
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Aspect Ratio ◽  
Heat Transfer Enhancement ◽  
Rotation Number ◽  
Pressure Loss ◽  
Heat Transfer Analysis ◽  
Internal Cooling ◽  
Transfer Enhancement ◽  
First Passage

Abstract The internal cooling passages of gas turbine blades mostly have varying aspect ratios from one passage to another. However, there are limited data available in the open literature that used a reduced cross-section and aspect ratio, AR, after the tip turn. Therefore, the current study presents heat transfer and pressure drop of three different α = 45° profiled rib orientations, typical parallel (usual), reversed parallel (unusual), and criss-cross patterns in a rotating two-pass rectangular channel with AR = 4:1 and 2:1 in the first radially outward flow and second radially inward flow passages respectively. For each rib orientation, regional averaged heat transfer results are obtained for both the flow passages with the Reynolds number ranging from 10,000 to 70,000 for the first passage and 16000 to 114000 for the second passage with a rotational speed range of 0 rpm to 400 rpm. This results in the highest rotation number of 0.39 and 0.16 for the first and second passage respectively. The effects of rib orientation, aspect ratio variation, 180° tip turn, and rotation number on the heat transfer and pressure drop will be addressed. According to the results, for usual, unusual and criss-cross rib patterns, increasing rotation number causes the heat transfer to decrease on the leading surface and increase on the trailing surface for the first passage and vice versa for the second passage. Overall heat transfer enhancement of the usual and unusual rib patterns is higher than criss-cross one. In terms of the pressure losses, the criss-cross rib pattern has the lowest and the usual rib pattern has the highest-pressure loss coefficients. When pressure loss and heat transfer enhancement are both taken into account together, the criss-cross or unusual rib pattern might be an option to use in the internal cooling method. Therefore, the results can be useful for turbine blade internal cooling design and heat transfer analysis.

Heat Transfer Enhancement Induced by Cube- and Diamond-Shaped Block Arrays in Two-Pass High-Aspect Ratio Channels With a 180-Degree Turn

2010 ◽  
Author(s):  
Pavin Ganmol ◽  
Minking K. Chyu
Keyword(s):  
Heat Transfer ◽  
Aspect Ratio ◽  
Heat Transfer Enhancement ◽  
High Aspect Ratio ◽  
Local Heat Transfer ◽  
Channel Height ◽  
Transfer Enhancement ◽  
Smooth Channel ◽  
Sharp Turn ◽  
First Pass

Described in this paper is an experimental investigation of the heat transfer and pressure characteristics in a high aspect ratio, (4.5:1 width-to-height), two-pass channel, with cube-shaped and diamond-shaped block arrays placed in both passes before and after a 180-degree sharp turn. Transient liquid crystal technique was applied to acquire detailed local heat transfer data on both the channel surfaces and the block elements. Reynolds number tested varies between 13000 and 28000. To further explore potential design alternatives for enhancement cooling, the effects of block height, ranging from 1/4, 1/2, 3/4 and full span of the channel height were also evaluated. Present results suggest that a staggered cube-array can enhance heat transfer rate up to 3.5 fold in the first pass and about 1.9 fold in the second pass, relative to the fully-developed smooth channel counterpart. For the corresponding diamond-shaped block array, the enhancement is 3.4 and 1.9 fold respectively. Even though the post-turn turbulence transport in the second pass is generally higher than that in the first pass, the effects of surface-block induced heat transfer enhancement in fact are less prominent in the post-turn region of the second pass. Pressure loss for diamond block arrays is generally higher than that of the corresponding cube-block arrays.

Effect of 45-deg Rib Orientations on Heat Transfer in a Rotating Two-Pass Channel With Aspect Ratio from 4:1 to 2:1

2020 ◽  
Vol 142 (7) ◽  
Author(s):  
Izzet Sahin ◽  
Andrew F Chen ◽  
Chao-Cheng Shiau ◽  
Je-Chin Han ◽  
Robert Krewinkel
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Aspect Ratio ◽  
Heat Transfer Enhancement ◽  
Rotation Number ◽  
Pressure Loss ◽  
Heat Transfer Analysis ◽  
Internal Cooling ◽  
Transfer Enhancement ◽  
First Passage

Abstract The internal cooling passages of gas turbine blades mostly have varying aspect ratios from one passage to another. However, there are limited data available in the open literature that used a reduced cross section and aspect ratio (AR), after the tip turn. Therefore, the current study presents heat transfer and pressure drop of three different α = 45 deg profiled rib orientations, typical parallel (usual), reversed parallel (unusual), and crisscross patterns in a rotating two-pass rectangular channel with AR = 4:1 and 2:1 in the first radially outward flow and second radially inward flow passages, respectively. For each rib orientation, regional averaged heat transfer results are obtained for both the flow passages with the Reynolds number ranging from 10,000 to 70,000 for the first passage and 16,000 to 114,000 for the second passage with a rotational speed range of 0–400 rpm. This results in the highest rotation number of 0.39 and 0.16 for the first and second passage respectively. The effects of rib orientation, aspect ratio variation, 180-deg tip turn, and rotation number on the heat transfer and pressure drop will be addressed. According to the results, for usual, unusual and crisscross rib patterns, increasing rotation number causes the heat transfer to decrease on the leading surface and increase on the trailing surface for the first passage and vice versa for the second passage. The overall heat transfer enhancement of the usual and unusual rib patterns is higher than the crisscross one. In terms of the pressure losses, the crisscross rib pattern has the lowest and the usual rib pattern has the highest-pressure loss coefficients. When pressure loss and heat transfer enhancement are both taken into account together, the crisscross or unusual rib pattern might be an option to use in the internal cooling method. Therefore, the results can be useful for the turbine blade internal cooling design and heat transfer analysis.

Experimental and Numerical Investigations of Thermal Hydraulic Performance in Ribbed Channel for Combustor Liner

2019 ◽  
Author(s):  
Divya Bihari ◽  
Sanjay Bokade
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Enhancement ◽  
Pressure Loss ◽  
Rectangular Channel ◽  
Hydraulic Performance ◽  
Transfer Enhancement ◽  
Ansys Fluent ◽  
Transfer Measurement ◽  
Steady State Heat Transfer

Abstract The present study assess the thermal hydraulic performance of V-shaped, W-shaped and 2W-shaped ribs in a rectangular channel with an aspect ratio of 6:1. The rib-roughened copper plates were located at the bottom of the channel to simulate the backside wall cooling of gas turbine combustor liners. The rib height-to-hydraulic diameter ratio (e/Dh) was 0.05834 and the rib pitch-to-height ratio (P/e) was 10 for all the cases. The experiments were carried out at the Reynolds numbers ranging from 32000 to 72000. A steady state heat transfer measurement method is used to investigate the heat transfer enhancement of ribbed wall against a smooth wall. Pressure taps were located at two stream-wise locations in channel walls to measure the pressure loss. To validate the understanding of experimental data, all the rib configurations were investigated numerically using ANSYS FLUENT. A low Reynolds number k-ε turbulence model was used to predict the heat transfer in the channel. The results show that the 2W ribs have the highest heat transfer and pressure loss characteristics in channel. It gives around 1.4–1.6 times increase in average Nusselt number and 2.7–3.3 times increase in friction factor as compare to smooth plate. Among all the cases V ribs obtained lowest heat transfer and pressure loss characteristics. Furthermore, both heat transfer enhancement and pressure loss increases with increasing Reynolds number.

Heat Transfer and Pressure Loss Measurements in a Turbulated High Aspect Ratio Channel With Large Reynolds Number Flows

2013 ◽  
Author(s):  
Shantanu Mhetras ◽  
Je-Chin Han ◽  
Michael Huth
Keyword(s):  
Heat Transfer ◽  
Steady State ◽  
Aspect Ratio ◽  
Heat Transfer Enhancement ◽  
Compressible Flow ◽  
Pressure Loss ◽  
Reynolds Numbers ◽  
Large Reynolds Number ◽  
Transfer Enhancement ◽  
Wide Wall

Experiments to investigate heat transfer and pressure loss are performed in a rectangular channel with an aspect ratio of 6 at very high Reynolds numbers under compressible flow conditions. Reynolds numbers up to 1.3 million are tested. The presence of a turbulated wall and the resultant heat transfer enhancement against a smooth surface is investigated. Three dimpled configurations including spherical and cylindrical dimples are studied on one wide wall of the channel. The presence of discrete ribs on the same wide wall is also investigated. A steady state heat transfer measurement method is used to obtain the heat transfer coefficients while pressure taps located at several streamwise locations in the channel walls are used to record the static pressures on the surface. Experiments are performed for a range of Reynolds numbers from 100,000 to 1,300,000 to cover the incompressible as well as compressible flow regimes. Results for low Reynolds numbers are compared to existing heat transfer data available in open literature for similar configurations. Heat transfer enhancement is found to decrease at high Re with the discrete rib configurations providing the best enhancement but highest pressure losses. Local measurements using the steady state, hue-detection based liquid crystal technique are also performed in the fully developed region for case 1 with dimples. Good comparison is obtained between averaged local heat transfer coefficient measurements and from thermocouple measurements.

Effect of Rib Spacing on Heat Transfer in a Two Pass Rectangular Channel (AR = 2:1) at High Rotation Numbers

2012 ◽  
Vol 134 (9) ◽  
Author(s):  
Jiang Lei ◽  
Je-Chin Han ◽  
Michael Huh
Keyword(s):  
Heat Transfer ◽  
Aspect Ratio ◽  
Heat Transfer Enhancement ◽  
Rectangular Channel ◽  
Orientation Angle ◽  
Reynolds Numbers ◽  
Transfer Enhancement ◽  
Flow Angle ◽  
Rotation Numbers ◽  
Channel Aspect Ratio

In this paper, the effect of rib spacing on heat transfer in a rotating two-passage channel (aspect ratio, AR = 2:1) at orientation angle of 135 deg was studied. Parallel ribs were applied’ on leading and trailing walls of the rotating channel at the flow angle of 45 deg. The rib-height-to-hydraulic diameter ratio (e/Dh) was 0.098. The rib-pitch-to-rib-height (P/e) ratios studied were 5, 7.5, and 10. For each rib spacing, tests were taken at five Reynolds numbers from 10,000 to 40,000, and for each Reynolds number, experiments were conducted at four rotational speeds up to 400 rpm. Results show that the heat transfer enhancement increases with decreasing P/e from 10 to 5 under nonrotation conditions. However, the effect of rotation on the heat transfer enhancement remains about the same for varying P/e from 10 to 5. Correlations of Nusselt number ratio (Nu/Nus) to rotation number (Ro) or local buoyancy parameter (Box) are existent on all surfaces (leading, trailing, inner and outer walls, and tip cap region) in the two-passage 2:1 aspect ratio channel.

Thermal Performance of Double-Sided, Partial Height Strip Fin Arrays in a High Aspect Ratio, Rectangular Channel

2021 ◽  
Author(s):  
Nathaniel J. Tracy ◽  
Lesley M. Wright ◽  
Je-Chin Han
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Thermal Performance ◽  
Rectangular Channel ◽  
Reynolds Numbers ◽  
Channel Height ◽  
Gap Size ◽  
Transfer Enhancement ◽  
Fin Thickness ◽  
Full Height

Abstract Friction loss and heat transfer enhancement measurements were obtained for double-sided, partial height, strip fin arrays within a high aspect ratio (AR = 8), rectangular channel. Fins were arranged in a staggered array configuration with channel height to fin thickness ratio H/W = 9.6, spanwise spacing distance to fin thickness ratio S/W = 8.0, and streamwise spacing distance to fin length ratio X/L = 1.0. Shortened strip fins of equal length are positioned directly opposite of each other on the upper and lower channel surfaces with three gap size to channel height ratios considered G/H = 0.2, 0.3, and 0.4. The thermal performance of each fin configuration is determined from the measured pressure drop across the array and regionally averaged heat transfer coefficients at flow Reynolds numbers ranging from Re = 20,000–80,000. The partial height strip fin results are compared to baseline cases of strip fins spanning the full height of the channel and the smooth channel without roughness elements. Linear correlations of friction loss and power correlations of the heat transfer enhancement and thermal performance are provided as functions of flow Reynolds numbers for all cases. Strip fins spanning the full height of the channel provide the greatest heat transfer enhancement of all cases but introducing a gap size can significantly reduce friction losses. Full height strip fins provide the greatest thermal performance for Reynolds numbers ranging from Re = 20,000–30,000, and partial height strip fins with the gap size of G/H = 0.3 provide the greatest thermal performance for flow Reynolds numbers ranging from Re = 40,000–80,000.

Sign in / Sign up

Export Citation Format

Share Document