Effects of Periodic Unsteady Inflow on Film Cooling and Heat Transfer on Highly Loaded High Pressure Turbine Blades With Flow Separation

2013 ◽  
Vol 136 (2) ◽  
Author(s):  
Reinaldo A. Gomes ◽  
Reinhard Niehuis
Keyword(s):  
Heat Transfer ◽  
Flow Separation ◽  
Film Cooling ◽  
High Speed ◽  
Turbine Blades ◽  
Suction Side ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Unsteady Inflow ◽  
Highly Loaded

Film cooling experiments were run at the high-speed cascade wind tunnel of the University of the Federal Armed Forces Munich. The investigations were carried out on a linear cascade of highly loaded turbine blades. The main targets of the tests were to assess the film cooling effectiveness and the heat transfer in zones with main flow separation. The previous cascade was designed to have a large zone with flow separation on the pressure side starting at the leading edge and reaching up to approximately half of the axial chord. This cascade was changed for a new design with a larger pitch to chord ratio in order to set the focus on flow separation on the suction side. This increased pitch forces a massive separation on the suction side due to strong shocks. The flow separation is controlled with aid of vortex generating jets in order to reduce the total pressure loss caused by it. Film cooling is provided on the suction side upstream of the vortex generating jets. The measurements comprise of blade loading, profile loss, adiabatic film cooling effectiveness, and heat transfer coefficient under two Mach numbers at a Reynolds number of 390,000. In a previous publication detailed results with homogeneous inflow where shown. Now, the focus is set on the effects of periodic unsteady wakes resulting from bars moving upstream of the cascade. These moving bars create a periodic unsteady inflow similar to the interaction between stator and rotor in the machine. It is shown how these wakes have significant influence on the heat transfer in the acceleration region of the suction side and affect the adiabatic film cooling effectiveness upstream of the shock.

Effects of Periodic Unsteady Inflow on Film Cooling and Heat Transfer on Highly Loaded High Pressure Turbine Blades With Flow Separation

2012 ◽  
Author(s):  
Reinaldo A. Gomes ◽  
Reinhard Niehuis
Keyword(s):  
Heat Transfer ◽  
Flow Separation ◽  
Film Cooling ◽  
High Speed ◽  
Turbine Blades ◽  
Suction Side ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Unsteady Inflow ◽  
Highly Loaded

Film cooling experiments were run at the High-Speed Cascade Wind Tunnel of the University of the Federal Armed Forces Munich. The investigations were carried out on a linear cascade of highly loaded turbine blades. The main targets of the tests were to assess the film cooling effectiveness and the heat transfer in zones with main flow separation. The previous cascade was designed to have a large zone with flow separation on the pressure side starting at the leading edge and reaching up to approximately half of the axial chord. This cascade was changed for a new design with a larger pitch to chord ratio in order to set the focus on flow separation on the suction side. This increased pitch forces a massive separation on the suction side due to strong shocks. The flow separation is controlled with aid of vortex generating jets in order to reduce the total pressure loss caused by it. Film cooling is provided on the suction side upstream of the vortex generating jets. The measurements comprise of blade loading, profile loss, adiabatic film cooling effectiveness and heat transfer coefficient under two Mach numbers at a Reynolds number of 390,000. In a previous publication detailed results with homogeneous inflow where shown. Now, the focus is set on the effects of periodic unsteady wakes resulting from bars moving upstream of the cascade. These moving bars create a periodic unsteady inflow similar to the interaction between stator and rotor in the machine. It is shown how these wakes have significant influence on the heat transfer in the acceleration region of the suction side and affect the adiabatic film cooling effectiveness upstream of the shock.

Film Cooling Effectiveness Measurements With Periodic Unsteady Inflow on Highly Loaded Blades With Main Flow Separation

2009 ◽  
Author(s):  
Reinaldo A. Gomes ◽  
Reinhard Niehuis
Keyword(s):  
Flow Separation ◽  
Film Cooling ◽  
Reynolds Numbers ◽  
Main Flow ◽  
Cooling Effectiveness ◽  
Temperature Correlation ◽  
Film Cooling Effectiveness ◽  
Unsteady Inflow ◽  
Highly Loaded ◽  
Mach And Reynolds Numbers

Film cooling experiments were performed using a highly loaded HPT blade linear cascade. A large region with main flow separation is found on the pressure side and film cooling is provided into this area with three rows of either cylindrical or fan-shaped holes. The measurements comprise adiabatic film cooling effectiveness and profile static pressure measurements. The surface temperature was acquired with thermochromatic liquid crystals and using a hue to temperature correlation. The results shown are for variations of main flow Mach and Reynolds numbers at engine relevant levels and of coolant mass flows. The results for steady and periodic unsteady inflow with highly turbulent wakes created by cylindrical bars moving upstream in a plane parallel to the cascade are compared as two-dimensional surface plots, laterally averaged film cooling effectiveness and overall effectiveness over the entire surface.

Film Cooling Effectiveness Measurements With Periodic Unsteady Inflow on Highly Loaded Blades With Main Flow Separation

2010 ◽  
Vol 133 (2) ◽  
Author(s):  
Reinaldo A. Gomes ◽  
Reinhard Niehuis
Keyword(s):  
Flow Separation ◽  
Film Cooling ◽  
Reynolds Numbers ◽  
Main Flow ◽  
Cooling Effectiveness ◽  
Temperature Correlation ◽  
Film Cooling Effectiveness ◽  
Unsteady Inflow ◽  
Highly Loaded ◽  
Mach And Reynolds Numbers

Film cooling experiments were performed using a highly loaded high pressure turbine blade blade linear cascade. A large region with main flow separation is found on the pressure side and film cooling is provided into this area with three rows of either cylindrical or fan-shaped holes. The measurements comprise adiabatic film cooling effectiveness and profile static pressure measurements. The surface temperature was acquired with thermochromatic liquid crystals and using a hue to temperature correlation. The results shown are for variations in main flow Mach and Reynolds numbers at engine relevant levels and of coolant mass flows. The results for steady and periodic unsteady inflows with highly turbulent wakes created by cylindrical bars moving upstream in a plane parallel to the cascade are compared as two-dimensional surface plots, laterally averaged film cooling effectiveness and overall effectiveness over the entire surface.

Film Cooling on Highly Loaded Blades With Main Flow Separation—Part I: Heat Transfer

2012 ◽  
Vol 135 (1) ◽  
Author(s):  
Reinaldo A. Gomes ◽  
Reinhard Niehuis
Keyword(s):  
Heat Transfer ◽  
Flow Separation ◽  
Film Cooling ◽  
Separation Bubble ◽  
Leading Edge ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Main Flow ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness

Film cooling experiments were run at the high speed cascade wind tunnel of the University of the Federal Armed Forces Munich. The investigations were carried out with a linear cascade of highly loaded turbine blades. The main objectives of the tests were to assess the film cooling effectiveness and the heat transfer in zones with main flow separation. Therefore, the blades were designed to force the flow to detach on the pressure side shortly downstream of the leading edge and reattach at about half of the axial chord. In this zone, film cooling rows are placed among others for a reduction of the size of the separation bubble. The analyzed region on the blade is critical due to the high heat transfer present at the leading edge and at the reattachment line after the main flow separation. Film cooling can contribute to a reduction of the size of the separation bubble reducing aerodynamic losses, however, in general, it increases heat transfer due to turbulent mixing. The reduction of the size of the separation bubble might also be twofold, since it acts like a thermal insulator on the blade and reducing the size of the bubble might lead to a stronger heating of the blade. Film cooling should, therefore, take both into account: first, a proper protection of the surface and second, reducing aerodynamic losses, diminishing the extension of the main flow separation. While experimental results of the adiabatic film cooling effectiveness were shown in previous publications, the local heat transfer is analyzed in this paper. Emphasis is also placed upon analyzing, in detail, the flow separation process. Furthermore, the tests comprise the analysis of the effect of different outlet Mach and Reynolds numbers and film cooling. In part two of this paper, the overall film cooling effectiveness is addressed. Local heat transfer is still difficult to predict with modern numerical tools and this is especially true for complex flows with flow separation. Some numerical results with the Reynolds averaged Navier-Stokes (RANS) and large eddy simulation (LES) show the capability of a commercial solver in predicting the heat transfer.

Effect of Hole Diameter on Nozzle Endwall Film Cooling and Associated Phantom Cooling

2015 ◽  
Author(s):  
Luzeng Zhang ◽  
Juan Yin ◽  
Kevin Liu ◽  
Moon Hee-Koo
Keyword(s):  
Film Cooling ◽  
High Speed ◽  
Leading Edge ◽  
Suction Side ◽  
Hole Diameter ◽  
Two Dimensional ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Injection Angle ◽  
Blowing Ratio

Flow fields near the turbine nozzle endwall are highly complex due to the passage vortices and endwall cross flows. Consequently, it is challenging to provide proper cooling to the endwall surfaces. An effective way to cool the endwall is to have film cooling holes forward of the leading edge, often called “inlet-film cooling”. This paper presents the results of an experimental investigation on how the film hole diameter affects the film effectiveness on nozzle endwall and associated phantom cooling effectiveness on airfoil suction side. The measurements were conducted in a high speed linear cascade, which consists of three nozzle vanes and four flow passages. Double staggered rows of film injections, which were located upstream from the nozzle leading edge, provided cooling to the contoured endwall surfaces. Film cooling effectiveness on the endwall surface and corresponding phantom cooling effectiveness on the airfoil suction side were measured separately with a Pressure Sensitive Paint (PSP) technique through the mass transfer analogy. Four different film hole diameters with the same injection angle and the same pitch to diameter ratio were studied for up to six different MFR’s (mass flow ratios). Two dimensional film effectiveness distributions on the endwall surface and two dimensional phantom cooling distributions on the airfoil suction side are presented. Film/phantom cooling effectiveness distributions are pitchwise/spanwise averaged along the axial direction and also presented. The results indicate that both the endwall film effectiveness and the suction side phantom cooling effectiveness increases with the hole diameter (as decreases in blowing ratio for a given MFR) up to a specific diameter, then starts decreasing. An optimal value of the film hole diameter (blowing ratio) for the given injection angle is also suggested based on current study.

Film Cooling on Highly Loaded Blades With Main Flow Separation—Part II: Overall Film Cooling Effectiveness

2012 ◽  
Vol 135 (1) ◽  
Author(s):  
Reinaldo A. Gomes ◽  
Reinhard Niehuis
Keyword(s):  
Heat Transfer ◽  
Flow Separation ◽  
Film Cooling ◽  
Separation Bubble ◽  
Leading Edge ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Main Flow ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness

Film cooling experiments were run at the high speed cascade wind tunnel of the University of the Federal Armed Forces Munich. The investigations were carried out with a linear cascade of highly loaded turbine blades. The main targets of the tests were to assess the film cooling effectiveness and the heat transfer in zones with main flow separation. Therefore the blades were designed to force the flow to detach on the pressure side shortly downstream of the leading edge and it reattaches at about half of the axial chord. In this zone, film cooling rows are placed among others for reduction of the size of the separation bubble. The analyzed region on the blade is critical due to the high heat transfer present at the leading edge and at the reattachment line after main flow separation. Film cooling can contribute to a reduction of the size of the separation bubble reducing aerodynamic losses but increases in general heat transfer due to turbulent mixing. The reduction of the size of the separation bubble might also be two-fold since it acts like a thermal insulator on the blade and reducing the size of the bubble might lead to stronger heating of the blade. Film cooling should therefore take into account both: firstly, a proper protection of the surface, and secondly, reduce aerodynamic losses diminishing the extension of the main flow separation. The overall effectiveness of film cooling for a real engine has to combine heat transfer with film cooling effect. In this paper, the overall effectiveness of film cooling, combining results from measurements of the adiabatic film cooling effectiveness and the local heat transfer coefficient are shown. The tests comprise the analysis of the effect of different outlet Mach and Reynolds numbers at engine relevant values and film cooling ratio. A new parameter is introduced which allows for the evaluation of the effect of film cooling accounting at the same time for the change of local heat transfer coefficient. To the authors’ opinion this parameter allows a better, physically based assessment than the strategy using the so-called heat flux ratio. A parameter study is carried out in order to benchmark the effect of changes of the blade design.

Trailing Edge Film Cooling of Gas Turbine Airfoils: External Cooling Performance of Various Internal Pin Fin Configurations

2010 ◽  
Author(s):  
T. Horbach ◽  
A. Schulz ◽  
H.-J. Bauer
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Turbine Blades ◽  
Back Surface ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Major Interest ◽  
Pin Fins ◽  
Discharge Behavior

The present paper describes an experimental study on trailing edge film cooling of modern high-pressure turbine blades using coolant ejection through planar slots on a pressure side cutback. The experimental test section consists of a generic scaled-up trailing edge model in an atmospheric open loop wind tunnel, which has been used in earlier studies by Martini et al. (e.g. [1]). An infrared thermographic measurement technique is employed, which allows for the application of engine-realistic density ratios around 1.6 by increasing the main flow temperature. The effects of different geometric configurations on the structure and performance of the cooling film are investigated in terms of film cooling effectiveness, heat transfer, and discharge behavior. Among other issues, the interaction between internal turbulators, namely an array of pin fins, with the ejection slot lip is of major interest. Therefore, different designs of the coolant ejection lip are studied. Four different ratios of lip thickness to ejection slot height (t/H = 0.2, 0.5, 1.0, 1.5) are investigated as well as three different lip profiles representing typical manufacturing imperfections and wear. Other geometric variations comprise elliptic pin fins with spanwise and streamwise orientation and the application of land extensions from the internal coolant cavity onto the cut-back surface. The blowing ratio is varied between 0.2 < M < 1.25. In terms of film cooling effectiveness the results show a strong dependency on ejection lip thickness and minor improvements are obtained with a rounded ejection lip profile. Significant improvements are achieved using land extensions. The elliptic pin fins have a strong effect on discharge behavior as well as on film cooling effectiveness and heat transfer. Except for the elliptic pin fins, the geometric variations have only a minor influence on heat transfer.

Numerical Prediction of Film Cooling and Heat Transfer on the Leading Edge of a Rotating Blade With Two Rows Holes in a 1-1/2 Turbine Stage at Design and Off Design Conditions

2005 ◽  
Author(s):  
Huitao Yang ◽  
Hamn-Ching Chen ◽  
Je-Chin Han ◽  
Hee-Koo Moon
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Leading Edge ◽  
Suction Side ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Rotating Speed ◽  
Rotating Blade

Numerical simulations were performed to predict the film cooling effectiveness and the associated heat transfer coefficient on the leading edge of a rotating blade in a 1-1/2 turbine stage using a Reynolds stress turbulence model together with a non-equilibrium wall function. Simulations were performed for both the design and off-design conditions to investigate the effects of blade rotation on the leading edge film cooling effectiveness and heat transfer coefficient distributions. It was found that the tilt stagnation line on the leading edge of rotor moves from the pressure side to the suction side, and the instantaneous coolant streamlines shift from the suction side to the pressure side with increasing rotating speed. This trend was supported by the experimental results. The result also showed that the heat transfer coefficient increases, but film cooling effectiveness decreases with increasing rotating speed. In addition, the unsteady characteristics of the film cooling and heat transfer at different time phases, as well as different rotating speeds, were also reported.

Investigation of Detailed Film Cooling Effectiveness and Heat Transfer Distributions on a Gas Turbine Airfoil

1998 ◽  
Author(s):  
U. Drost ◽  
A. Bölcs
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Density Ratio ◽  
Suction Side ◽  
Lateral Spreading ◽  
Double Row ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Flow Acceleration ◽  
Single Compound

In the present study film cooling effectiveness and heat transfer were systematically investigated on a turbine NGV airfoil employing the transient liquid crystal technique and a multiple regression procedure. Tests were conducted in a linear cascade at exit Reynolds numbers of 0.52e6, 1.02e6 and 1.45e6 and exit Mach numbers of 0.33, 0.62 and 0.8, at two mainstream turbulence intensities of 5.5% and 10%. The film cooling geometry consisted of a single compound angle row on the pressure side (PS), and a single or a double row on the suction side (SS). Foreign gas injection was used to obtain a density ratio of approximately 1.65, while air injection yielded a density ratio of unity. Tests were conducted for blowing ratios of 0.25 to 2.3 on the SS, and 0.55 to 7.3 on the PS. In general film cooling injection into a laminar BL showed considerably higher effectiveness in the near hole region, as compared to a turbulent BL. While mainstream turbulence had only a weak influence on SS cooling, higher effectiveness was noted on the PS at high turbulence due to increased lateral spreading of the coolant. Effects of mainstream Mach and Reynolds number were attributed to changes of the BL thickness and flow acceleration. Higher density coolant yielded higher effectiveness on both SS and PS, whereas heat transfer ratios were increased on the SS and decreased on the PS. Comparison of the single and double row cooling configurations on the SS revealed a better film cooling performance of the double row due to an improved film coverage and delayed jet separation.

Sign in / Sign up

Export Citation Format

Share Document