Time-Averaged and Time-Accurate Aerodynamic Effects of Forward Rotor Cavity Purge Flow for a High-Pressure Turbine—Part I: Analytical and Experimental Comparisons

2013 ◽  
Vol 136 (1) ◽  
Author(s):  
Brian R. Green ◽  
Randall M. Mathison ◽  
Michael G. Dunn
Keyword(s):  
High Pressure ◽  
Flow Field ◽  
Film Cooling ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Unsteady Aerodynamics ◽  
Flow Path ◽  
Field Analysis ◽  
High Pressure Turbine ◽  
Purge Flow

The effect of rotor purge flow on the unsteady aerodynamics of a high-pressure turbine stage operating at design corrected conditions has been investigated, both experimentally and computationally. The experimental configuration consisted of a single-stage high-pressure turbine with a modern film-cooling configuration on the vane airfoil and the inner and outer end wall surfaces. Purge flow was introduced into the cavity located between the high-pressure vane and the high-pressure disk. The high-pressure blades and the downstream low-pressure turbine nozzle row were not cooled. All of the hardware featured an aerodynamic design typical of a commercial high-pressure ratio turbine and the flow path geometry was representative of the actual engine hardware. In addition to instrumentation in the main flow path, the stationary and rotating seals of the purge flow cavity were instrumented with high frequency response flush-mounted pressure transducers and miniature thermocouples in order to measure the flow field parameters above and below the angel wing. Predictions of the time-dependent flow field in the turbine flow path were obtained using FINE/Turbo, a three-dimensional Reynolds-averaged Navier–Stokes computational fluid dynamics CFD code that had the capability to perform both a steady and unsteady analysis. The steady and unsteady flow fields throughout the turbine were predicted using a three blade-row computational model that incorporated the purge flow cavity between the high-pressure vane and disk. The predictions were performed in an effort to mimic the design process with no adjustment of boundary conditions to better match the experimental data. The time-accurate predictions were generated using the harmonic method. Part I of this paper concentrates on the comparison of the time-averaged and time-accurate predictions with measurements in and around the purge flow cavity. The degree of agreement between the measured and predicted parameters is described in detail, providing confidence in the predictions for the flow field analysis that will be provided in Part II.

Time-Averaged and Time-Accurate Aerodynamic Effects of Forward Rotor Cavity Purge Flow for a High-Pressure Turbine: Part I—Analytical and Experimental Comparisons

2012 ◽  
Author(s):  
Brian R. Green ◽  
Randall M. Mathison ◽  
Michael G. Dunn
Keyword(s):  
High Pressure ◽  
Flow Field ◽  
Film Cooling ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Unsteady Aerodynamics ◽  
Flow Path ◽  
Field Analysis ◽  
High Pressure Turbine ◽  
Purge Flow

The effect of rotor purge flow on the unsteady aerodynamics of a high-pressure turbine stage operating at design corrected conditions has been investigated both experimentally and computationally. The experimental configuration consisted of a single-stage high-pressure turbine with a modern film-cooling configuration on the vane airfoil as well as the inner and outer end-wall surfaces. Purge flow was introduced into the cavity located between the high-pressure vane and the high-pressure disk. The high-pressure blades and the downstream low-pressure turbine nozzle row were not cooled. All hardware featured an aerodynamic design typical of a commercial high-pressure ratio turbine, and the flow path geometry was representative of the actual engine hardware. In addition to instrumentation in the main flow path, the stationary and rotating seals of the purge flow cavity were instrumented with high frequency response, flush-mounted pressure transducers and miniature thermocouples to measure flow field parameters above and below the angel wing. Predictions of the time-dependent flow field in the turbine flow path were obtained using FINE/Turbo, a three-dimensional, Reynolds-Averaged Navier-Stokes CFD code that had the capability to perform both steady and unsteady analysis. The steady and unsteady flow fields throughout the turbine were predicted using a three blade-row computational model that incorporated the purge flow cavity between the high-pressure vane and disk. The predictions were performed in an effort to mimic the design process with no adjustment of boundary conditions to better match the experimental data. The time-accurate predictions were generated using the harmonic method. Part I of this paper concentrates on the comparison of the time-averaged and time-accurate predictions with measurements in and around the purge flow cavity. The degree of agreement between the measured and predicted parameters is described in detail, providing confidence in the predictions for flow field analysis that will be provided in Part II.

Time-Averaged and Time-Accurate Aerodynamic Effects of Rotor Purge Flow for a Modern, One and One-Half Stage High-Pressure Turbine—Part II: Analytical Flow Field Analysis

2013 ◽  
Vol 136 (1) ◽  
Author(s):  
Brian R. Green ◽  
Randall M. Mathison ◽  
Michael G. Dunn
Keyword(s):  
High Pressure ◽  
Flow Field ◽  
Film Cooling ◽  
Gas Flow ◽  
Static Pressure ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Field Analysis ◽  
High Pressure Turbine ◽  
Purge Flow

The detailed mechanisms of purge flow interaction with the hot-gas flow path were investigated using both unsteady computationally fluid dynamics (CFD) and measurements for a turbine operating at design corrected conditions. This turbine consisted of a single-stage high-pressure turbine and the downstream, low-pressure turbine nozzle row with an aerodynamic design equivalent to actual engine hardware and typical of a commercial, high-pressure ratio, transonic turbine. The high-pressure vane airfoils and inner and outer end walls incorporated state-of-the-art film cooling, and purge flow was introduced into the cavity located between the high-pressure vane and disk. The flow field above and below the blade angel wing was characterized by both temperature and pressure measurements. Predictions of the time-dependent flow field were obtained using a three-dimensional, Reynolds-averaged Navier–Stokes CFD code and a computational model incorporating the three blade rows and the purge flow cavity. The predictions were performed to evaluate the accuracy obtained by a design style application of the code, and no adjustment of boundary conditions was made to better match the experimental data. Part I of this paper compared the predictions to the measurements in and around the purge flow cavity and demonstrated good correlation. Part II of this paper concentrates on the analytical results, looking at the primary gas path ingestion mechanism into the cavity as well as the effects of the rotor purge on the upstream vane and downstream rotor aerodynamics and thermodynamics. Ingestion into the cavity is driven by high static pressure regions downstream of the vane, high-velocity flow coming off the pressure side of the vane, and the blade bow waves. The introduction of the purge flow is seen to have an effect on the static pressure of the vane trailing edge in the lower 5% of span. In addition, the purge flow is weak enough that upon exiting the cavity, it is swept into the mainstream flow and provides no additional cooling benefits on the platform of the rotating blade.

Time-Averaged and Time-Accurate Aerodynamic Effects of Rotor Purge Flow for a Modern, One and One-Half Stage High-Pressure Turbine: Part II—Analytical Flow Field Analysis

2012 ◽  
Author(s):  
Brian R. Green ◽  
Randall M. Mathison ◽  
Michael G. Dunn
Keyword(s):  
High Pressure ◽  
Flow Field ◽  
Film Cooling ◽  
Gas Flow ◽  
Static Pressure ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Field Analysis ◽  
High Pressure Turbine ◽  
Purge Flow

The detailed mechanisms of purge flow interaction with the hot-gas flow path were investigated using both unsteady CFD and measurements for a turbine operating at design corrected conditions. This turbine consisted of a single-stage high-pressure turbine and the downstream, low-pressure turbine nozzle row with an aerodynamic design equivalent to actual engine hardware and typical of a commercial, high-pressure ratio, transonic turbine. The high-pressure vane airfoils and inner and outer endwalls incorporated state-of-the-art film cooling, and purge flow was introduced into the cavity located between the high-pressure vane and disk. The flow field above and below the blade angel wing was characterized by both temperature and pressure measurements. Predictions of the time-dependent flow field were obtained using a three-dimensional, Reynolds-Averaged Navier-Stokes CFD code and a computational model incorporating the three blade rows and the purge flow cavity. The predictions were performed to evaluate the accuracy obtained by a design style application of the code, and no adjustment of boundary conditions was made to better match the experimental data. Part I of this paper compared the predictions to the measurements in and around the purge flow cavity and demonstrated good correlation. Part II of this paper concentrates on the analytical results, looking at the primary gas path ingestion mechanism into the cavity as well as the effects of the rotor purge on the upstream vane and downstream rotor aerodynamics and thermodynamics. Ingestion into the cavity is driven by high static pressure regions downstream of the vane, high-velocity flow coming off the pressure side of the vane, and the blade bow waves. The introduction of the purge flow is seen to have an effect on the static pressure of the vane trailing edge in the lower 5% of span. In addition, the purge flow is weak enough that upon exiting the cavity, it is swept into the mainstream flow and provides no additional cooling benefits on the platform of the rotating blade.

A Systematic Experimental Study on the Aerodynamics of Leading Edge Film Cooling on a Large Scale High Pressure Turbine Cascade

1998 ◽  
Author(s):  
Sabine Ardey ◽  
Leonhard Fottner
Keyword(s):  
High Pressure ◽  
Flow Field ◽  
Injection Site ◽  
Film Cooling ◽  
Gas Turbines ◽  
Large Scale ◽  
Three Dimensional ◽  
Leading Edge ◽  
Turbine Cascade ◽  
High Pressure Turbine

Systematic isothermal investigations on the aerodynamic effects of leading edge film cooling were carried out on a large scale high pressure turbine cascade named AGTB. In the vicinity of the stagnation point the AGTB turbine cascade has one injection site on the suction side and one on the pressure side. Three injection geometries were tested: Slots (two dimensional geometry), streamwise inclined holes (symmetrical three dimensional geometry) and compound angle holes (fully three dimensional geometry). The injection angle in streamwise direction, the blowing ratio, the inlet turbulence intensity, the inlet Mach number, and the inlet Reynolds number were kept constant at values typically found in modern gas turbines. The measured data comprise the coolant plenum state, the cascade inlet conditions, the flow field in the cascade exit plane including secondary flows, the static pressure distribution in the mid span section of the blade and in the near hole region, the coolant flow field close to the injection site on the leading edge, Schlieren images of the coolant penetration height and oil-and-dye flow visualizations of the blade surface. The experimental data are summarized and documented as a test case that can be used for validation purposes of prediction methods.

Design Optimization of Profiled Endwall With Consideration of Cooling and Rim Seal Flow Effects

2016 ◽  
Author(s):  
Huimin Tang ◽  
Shuaiqiang Liu ◽  
Hualing Luo
Keyword(s):  
High Pressure ◽  
Flow Field ◽  
Secondary Flow ◽  
Three Dimensional ◽  
Great Influence ◽  
Optimization Procedure ◽  
Secondary Flows ◽  
High Pressure Turbine ◽  
Operation Condition ◽  
Turbine Performance

Profiled endwall is an effective method to improve aerodynamic performance of turbine. This approach has been widely studied in the past decade on many engines. When automatic design optimisation is considered, most of the researches are usually based on the assumption of a simplified simulation model without considering cooling and rim seal flows. However, many researchers find out that some of the benefits achieved by optimization procedure are lost when applying the high-fidelity geometry configuration. Previously, an optimization procedure has been implemented by integrating the in-house geometry manipulator, a commercial three-dimensional CFD flow solver and the optimization driver, IsightTM. This optimization procedure has been executed [12] to design profiled endwalls for a turbine cascade and a one-and-half stage axial turbine. Improvements of the turbine performance have been achieved. As the profiled endwall is applied to a high pressure turbine, the problems of cooling and rim seal flows should be addressed. In this work, the effects of rim seal flow and cooling on the flow field of two-stage high pressure turbine have been presented. Three optimization runs are performed to design the profiled endwall of Rotor-One with different optimization model to consider the effects of rim flow and cooling separately. It is found that the rim seal flow has a significant impact on the flow field. The cooling is able to change the operation condition greatly, but barely affects the secondary flow in the turbine. The influences of the profiled endwalls on the flow field in turbine and cavities have been analyzed in detail. A significant reduction of secondary flows and corresponding increase of performance are achieved when taking account of the rim flows into the optimization. The traditional optimization mechanism of profiled endwall is to reduce the cross passage gradient, which has great influence on the strength of the secondary flow. However, with considering the rim seal flows, the profiled endwall improves the turbine performance mainly by controlling the path of rim seal flow. Then the optimization procedure with consideration of rim seal flow has also been applied to the design of the profiled endwall for Stator Two.

The Influence of Purge Flow Parameters on Heat Transfer and Film Cooling in Turbine Center Frames

2021 ◽  
Author(s):  
Patrick R. Jagerhofer ◽  
Marios Patinios ◽  
Tobias Glasenapp ◽  
Emil Göttlich ◽  
Federica Farisco
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Film Cooling ◽  
Convective Heat Transfer Coefficient ◽  
Density Ratio ◽  
Constant Heat Flux ◽  
High Pressure Turbine ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Purge Flow

Abstract Due to stringent environmental legislation and increasing fuel costs, the efficiencies of modern turbofan engines have to be further improved. Commonly, this is facilitated by increasing the turbine inlet temperatures in excess of the melting point of the turbine components. This trend has reached a point where not only the high-pressure turbine has to be adequately cooled, but also components further downstream in the engine. Such a component is the turbine center frame (TCF), having a complex aerodynamic flow field that is also highly influenced by purge-mainstream interactions. The purge air, being injected through the wheelspace cavities of the upstream high-pressure turbine, bears a significant cooling potential for the TCF. Despite this, fundamental knowledge of the influencing parameters on heat transfer and film cooling in the TCF is still missing. This paper examines the influence of purge-to-mainstream blowing ratio, purge-to-mainstream density ratio and purge flow swirl angle on the convective heat transfer coefficient and the film cooling effectiveness in the TCF. The experiments are conducted in a sector-cascade test rig specifically designed for such heat transfer studies using infrared thermography and tailor-made flexible heating foils with constant heat flux. The inlet flow is characterized by radially traversing a five-hole-probe. Three purge-to-mainstream blowing ratios and an additional no purge case are investigated. The purge flow is injected without swirl and also with engine-similar swirl angles. The purge swirl and blowing ratio significantly impact the magnitude and the spread of film cooling in the TCF. Increasing blowing ratios lead to an intensification of heat transfer. By cooling the purge flow, a moderate variation in purge-to-mainstream density ratio is investigated, and the influence is found to be negligible.

THE INFLUENCE OF PURGE FLOW PARAMETERS ON HEAT TRANSFER AND FILM COOLING IN TURBINE CENTER FRAMES

2021 ◽  
pp. 1-26
Author(s):  
Patrick René Jagerhofer ◽  
Marios Patinios ◽  
Tobias Glasenapp ◽  
Emil Goettlich ◽  
Federica Farisco
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Film Cooling ◽  
Density Ratio ◽  
Constant Heat Flux ◽  
Inlet Temperature ◽  
High Pressure Turbine ◽  
Turbofan Engines ◽  
Blowing Ratio ◽  
Purge Flow

Abstract The imperative improvement in the efficiency of turbofan engines is commonly facilitated by increasing the turbine inlet temperature. This development has reached a point where also components downstream of the high-pressure turbine have to be adequately cooled. Such a component is the turbine center frame (TCF), known for a complex aerodynamic flow highly influenced by purge-mainstream interactions. The purge air, being injected through the wheelspace cavities of the upstream high-pressure turbine, bears a significant cooling potential for the TCF. Despite this, fundamental knowledge of the influencing parameters on heat transfer and film cooling in the TCF is still missing. This paper examines the influence of purge-to-mainstream blowing ratio, density ratio and purge swirl angle on heat transfer and film cooling in the TCF. The experiments are conducted in a sector-cascade test rig specifically designed for such heat transfer studies using infrared thermography and tailor-made flexible heating foils with constant heat flux. Three purge-to-mainstream blowing ratios and an additional no purge case are investigated. The purge flow is injected without swirl and also with engine-similar swirl angles. The purge swirl and blowing ratio significantly impact the magnitude and the spread of film cooling in the TCF. Increasing blowing ratios lead to an intensification of heat transfer. By cooling the purge flow, a moderate variation in purge-to-mainstream density ratio is investigated, and the influence is found to be negligible.

Comparison of Steady and Unsteady Coupled Heat-Transfer Simulations of a High-Pressure Turbine Blade

2015 ◽  
Author(s):  
Markus Schmidt ◽  
Christoph Starke
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Steady State ◽  
Flow Field ◽  
Film Cooling ◽  
Strong Increase ◽  
Pressure Side ◽  
Turbine Stage ◽  
High Pressure Turbine ◽  
Time Resolved

This article presents results for the coupled simulation of a high-pressure turbine stage in consideration of unsteady hot gas flows. A semi-unsteady coupling process was developed to solve the conjugate heat transfer problem for turbine components of gas turbines. Time-resolved CFD simulations are coupled to a finite element solver for the steady state heat conduction inside of the blade material. A simplified turbine stage geometry is investigated in this paper to describe the influence of the unsteady flow field onto the time-averaged heat transfer. Comparisons of the time-resolved results to steady state results indicate the importance of a coupled simulation and the consideration of the time-dependent flow-field. Different film-cooling configurations for the turbine NGV are considered, resulting in different temperature and pressure deficits in the vane wake. Their contribution to non-linear effects causing the time-averaged heat load to differ from a steady result is discussed to further highlight the necessity of unsteady design methods for future turbine developments. A strong increase in the pressure side heat transfer coefficients for unsteady simulations is observed in all results. For higher film-cooling mass flows in the upstream row, the preferential migration of hot fluid towards the pressure side of a turbine blade is amplified as well, which leads to a strong increase in material temperature at the pressure side and also in the blade tip region.

scholarly journals Calculation and Correlation of the Unsteady Flowfield in a High Pressure Turbine

2002 ◽  
Author(s):  
Milind A. Bakhle ◽  
Jong S. Liu ◽  
Josef Panovsky ◽  
Theo G. Keith ◽  
Oral Mehmed
Keyword(s):  
High Pressure ◽  
Three Dimensional ◽  
Unsteady Aerodynamics ◽  
Forced Vibrations ◽  
Forced Response ◽  
Operating Conditions ◽  
Test Facility ◽  
Navier Stokes ◽  
Turbine Stage ◽  
High Pressure Turbine

Forced vibrations in turbomachinery components can cause blades to crack or fail due to high-cycle fatigue. Such forced response problems will become more pronounced in newer engines with higher pressure ratios and smaller axial gap between blade rows. An accurate numerical prediction of the unsteady aerodynamics phenomena that cause resonant forced vibrations is increasingly important to designers. Validation of the computational fluid dynamics (CFD) codes used to model the unsteady aerodynamic excitations is necessary before these codes can be used with confidence. Recently published benchmark data, including unsteady pressures and vibratory strains, for a high-pressure turbine stage makes such code validation possible. In the present work, a three dimensional, unsteady, multi blade-row, Reynolds-Averaged Navier Stokes code is applied to a turbine stage that was recently tested in a short duration test facility. Two configurations with three operating conditions corresponding to modes 2, 3, and 4 crossings on the Campbell diagram are analyzed. Unsteady pressures on the rotor surface are compared with data.

A Novel Vortex Identification Technique Applied to the 3D Flow Field of a High-Pressure Turbine

2019 ◽  
Author(s):  
Marek Pátý ◽  
Sergio Lavagnoli
Keyword(s):  
High Pressure ◽  
Flow Field ◽  
Pure Shear ◽  
Three Dimensional ◽  
Secondary Flows ◽  
Vortex Identification ◽  
3D Flow ◽  
High Pressure Turbine ◽  
Vortical Structures ◽  
Identification Technique

Abstract The efficiency of modern axial turbomachinery is strongly driven by the secondary flows within the vane or blade passages. The secondary flows are characterized by a complex pattern of vortical structures that origin, interact and dissipate along the turbine gas path. The endwall flows are responsible for the generation of a significant part of the overall turbine loss because of the dissipation of secondary kinetic energy and mixing-out of non-uniform momentum flows. The understanding and analysis of secondary flows requires a reliable vortex identification technique to predict and analyse the impact of specific turbine designs on the turbine performance. However, literature shows a remarkable lack of general methods to detect vortices and to determine the location of their cores and to quantify their strength. This paper presents a novel technique for the identification of vortical structures in a general 3D flow field. The method operates on the local flow field and it is based on a triple decomposition of motion proposed by Kolář. In contrast to a decomposition of velocity gradient into the strain and vorticity tensors, this method considers a third, pure shear component. The subtraction of the pure shear tensor from the velocity gradient remedies the inherent flaw of vorticity-based techniques which cannot distinguish between rigid rotation and shear. The triple decomposition of motion serves to obtain a 3D field of residual vorticity whose magnitude is used to define vortex regions. The present method allows to locate automatically the core of each vortex, quantify its strength and determine the vortex bounding surface. The output may be used to visualize the turbine vortical structures for the purpose of interpreting the complex three-dimensional viscous flow field, as well as to highlight any case-to-case variations by quantifying the vortex strength and location. The vortex identification method is applied to a high-pressure turbine with three optimized blade tip geometries. The 3D flow-field is obtained by CFD computations performed with Numeca FINE/Open. The computational model uses steady-state RANS equations closed by the Spalart-Allmaras turbulence model. Although developed for turbomachinery applications, the vortex identification method proposed in this work is of general applicability to any three-dimensional flow-field.

Sign in / Sign up

Export Citation Format

Share Document