Influence of a Shroud Axisymmetric Slot Injection on a High Pressure Turbine Flow

This paper focuses on an axisymmetric slot injecting cooling air at the casing between the stator and the rotor in a one-stage unshrouded transonic high pressure turbine. This configuration has been studied with the help of unsteady RANS computations with and without the slot. Special care has been taken to model and describe the interaction induced unsteady mechanisms. It has been found that the cooling air is ejected from the axisymmetric slot at a fixed position with respect to the stator vanes, with a much lower incidence angle than the main stream. The flow through the rotor passage is highly modified and reveals an unsteady behaviour which highlights the necessity of using unsteady simulations in order to accurately model such a configuration. The effect on the efficiency and on the repartition of loss generation has been determined. As several different definitions of the efficiency can be used for cooled turbine cases, this choice is discussed. In particular, Young & Horlock’s “Weighted Pressure” definition, which takes into account some unavoidable mixing losses in the definition of the ideal process, is evaluated. With this definition, the slot does not yield any significant decrease in overall efficiency.

Impact of the Expansion Ratio on the Unsteady Aerodynamics and Performance of a HP Axial Turbine

In the frame of the European research project RECORD, the flow field within a HP axial-flow turbine model was investigated experimentally for several operating conditions. A number of studies on stator-rotor interaction in HP turbines for subsonic as well as transonic/supersonic conditions were proposed in the last decades, but none of them compared different conditions for the same geometry. In this paper, the transonic condition is investigated and compared to three subsonic ones, in the frame of an entirely new experimental campaign. The research was performed at the Laboratorio di Fluidodinamica delle Macchine of the Politecnico di Milano (Italy), where a cold-flow, closed-loop test rig is available for detailed studies on turbines and compressors. The boundary conditions resulted in keeping constant both the turbine inlet temperature and the stage outlet absolute flow direction; so far, while the expansion ratio was varied, the rotational speed was also modified accordingly. The analysis was performed by means of a conventional five hole probe in the stator – rotor axial gap and by a fast response aerodynamic probe downstream of the rotor. The local time-averaged and phase-resolved flow field was then derived and used to analyze the stage aerodynamics and performance. Results show that the stage expansion ratio has a dramatic impact on both the rotor aerodynamics and stage performance. In particular, Mach number effects are recognized in the stator cascade that passes from transonic to low subsonic conditions. On the rotor cascade the reduction of expansion ratio reduces significantly the Mach and Reynolds numbers and increases the incidence angle as well; the rotor loss mechanics as well as the vane-rotor interaction are greatly amplified. Correspondingly a significant variation of stage overall efficiency is recorded.

Experimental and Numerical Investigations on the Aerodynamic Performance of the Three-Stage Turbine With Consideration of the Leakage Flow Effect

The aerodynamic performance of three-stage turbine with different types of leakage flows was experimentally and numerically studied in this paper. The leakage flows of three-stage turbine included the shroud seal leakage flow between the rotor blade tip and case, the diaphragm seal leakage flow between the stator blade diaphragm and shaft, as well as the shaft packing leakage flow and the gap leakage flow between the rotor blade curved fir-tree root and wheel disk. The total aerodynamic performance of three-stage turbine including leakage flows was firstly experimentally measured. The detailed flow field and aerodynamic performance were also numerically investigated using three-dimensional Reynolds-Averaged Navier-Stokes (RANS) and S-A turbulence model. The numerical mass flow rate and efficiency showed well agreement with experimental data. The effects of leakage flows between the fir-tree root and the wheel disk were studied. All leakage mass flow fractions, including the mass flow rate in each hole for all sets of root gaps were given for comparison. The effect of leakage flow on the aerodynamic performance of three-stage was illustrated and discussed.

Experimental Investigation on the Annular Sector Cascade of a High Endwall-Angle Turbine

The flow in high endwall-angle turbine is complex, and it is different from the ordinary turbine flow in characteristics. In order to study the flow field characteristics of high endwall-angle turbines, the annular sector cascade experimental study of high endwall-angle turbines is carried out. The blade is studied experimentally in the form of annular sector cascade. The cascade includes 7 blades, and makes up 6 flow passages, in order to simulate full cascade flow. The experimental Mach number is adjusted by the way of changing inlet total pressure, and the Mach number influence (0.7, 0.8 and 0.9) on annular sector cascade flow is studied. Based on it, the inlet incidence angle (−15°, −7.5°, 0°, 7.5° and 15° )is changed with the way of changing sector straight pipes upstream of the cascade, and its influence on turbine flow fields is studied at the Mach number of 0.8. Here, five-hole probes are used to measure aerodynamic parameters distributions downstream of the cascade, and static pressure taps are positioned on the blade surface to measure surface static pressure distribution. The auto-traversing system and pressure sensors were operated by a self-compiled program based control program. The results indicate that there are two passage vortices inside the turbine cascade flow passage under the high Mach number condition, and the passage vortex near the high endwall-angle region is bigger. As Mach number increases, the passage vortices inside turbine cascade passage will become strong, and moves towards the blade mid-span. Besides, it is shown that the way of changing sector straight pipes can achieve the variation of inlet incidence angles. And, the blade profile with big leading-edge radius has good design and off-design performance. Detailed results and analyses are presented in the paper.

Design Optimization of Profiled Endwall With Consideration of Cooling and Rim Seal Flow Effects

Profiled endwall is an effective method to improve aerodynamic performance of turbine. This approach has been widely studied in the past decade on many engines. When automatic design optimisation is considered, most of the researches are usually based on the assumption of a simplified simulation model without considering cooling and rim seal flows. However, many researchers find out that some of the benefits achieved by optimization procedure are lost when applying the high-fidelity geometry configuration. Previously, an optimization procedure has been implemented by integrating the in-house geometry manipulator, a commercial three-dimensional CFD flow solver and the optimization driver, IsightTM. This optimization procedure has been executed [12] to design profiled endwalls for a turbine cascade and a one-and-half stage axial turbine. Improvements of the turbine performance have been achieved. As the profiled endwall is applied to a high pressure turbine, the problems of cooling and rim seal flows should be addressed. In this work, the effects of rim seal flow and cooling on the flow field of two-stage high pressure turbine have been presented. Three optimization runs are performed to design the profiled endwall of Rotor-One with different optimization model to consider the effects of rim flow and cooling separately. It is found that the rim seal flow has a significant impact on the flow field. The cooling is able to change the operation condition greatly, but barely affects the secondary flow in the turbine. The influences of the profiled endwalls on the flow field in turbine and cavities have been analyzed in detail. A significant reduction of secondary flows and corresponding increase of performance are achieved when taking account of the rim flows into the optimization. The traditional optimization mechanism of profiled endwall is to reduce the cross passage gradient, which has great influence on the strength of the secondary flow. However, with considering the rim seal flows, the profiled endwall improves the turbine performance mainly by controlling the path of rim seal flow. Then the optimization procedure with consideration of rim seal flow has also been applied to the design of the profiled endwall for Stator Two.

Experimental Investigation of Turbine Stage Flow Field and Performance at Varying Cavity Purge Rates and Operating Speeds

The aspect of hub cavity purge has been investigated in a high-pressure axial low-reaction turbine stage. The cavity purge is an important part of the secondary air system, used to isolate the hot main annulus flow from cavities below the hub level. A full-scale cold-flow experimental rig featuring a rotating stage was used in the investigation, quantifying main annulus flow field impact with respect to purge flow rate as it was injected upstream of the rotor. Five operating speeds were investigated of which three with respect to purge flow, namely a high loading case, the peak efficiency, and a high speed case. At each of these operating speeds, the amount of purge flow was varied across a very wide range of ejection rates. Observing the effect of the purge rate on measurement plane averaged parameters, a minor outlet swirl decrease is seen with increasing purge flow for each of the operating speeds while the Mach number is constant. The prominent effect due to purge is seen in the efficiency, showing a similar linear sensitivity to purge for the investigated speeds. An attempt is made to predict the efficiency loss with control volume analysis and entropy production. While spatial average values of swirl and Mach number are essentially unaffected by purge injection, important spanwise variations are observed and highlighted. The secondary flow structure is strengthened in the hub region, leading to a generally increased over-turning and lowered flow velocity. Meanwhile, the added volume flow through the rotor leads to higher outlet flow velocities visible in the tip region, and an associated decreased turning. A radial efficiency distribution is utilized, showing increased impact with increasing rotor speed.

Secondary Flow Control in Low Aspect Ratio Vanes Using Splitters

Low aspect ratio vanes, often the result of overall engine architecture constraints, create strong secondary flows and high endwall loss. In this paper, a splitter concept is demonstrated that reduces secondary flow strength and improves stage performance. An analytic conceptual study, corroborated by inviscid computations, shows that the total secondary kinetic energy of the secondary flow vortices is reduced when the number of passages is increased and, for a given number of vanes, when the inlet endwall boundary layer is evenly distributed between the passages. Viscous computations show that, for this to be achieved in a splitter configuration, the pressure-side leg of the low aspect ratio vane horseshoe vortex, must enter the adjacent passage (and not “jump” in front of the splitter leading edge). For a target turbine application, four vane designs were produced using a multi-objective optimization approach. These designs represent: current practice for a low aspect ratio vane; a design exempt from thickness constraints; and two designs incorporating splitter vanes. Each geometry is tested experimentally, as a sector, within a low-speed turbine stage. The vane designs with splitters geometries were found to reduce the measured secondary kinetic energy, by up to 85%, to a value similar to the design exempt from thickness constraints. The resulting flowfield was also more uniform in both the circumferential and radial directions. One splitter design was selected for a full annulus test where a mixed-out loss reduction, compared to the current practice design, of 15.3% was measured and the stage efficiency increased by 0.88%.

Thermal Investigation of Integrated Combustor Vane Concept Under Engine-Realistic Conditions

This paper presents a thermal investigation of the Integrated Combustor Vane concept for power generation gas turbines with individual can combustors. This concept has the potential to replace the high-pressure turbine’s first vanes by prolonged combustor walls. Experimental measurements are performed on a linear high-speed cascade consisting of two can combustors and two integrated vanes. The modularity of the facility allows for the testing at engine-realistic high turbulence levels, as well as swirl strengths with opposing swirl directions. The heat transfer characteristics of the integrated vanes are compared to conventional nozzle guide vanes. The experimental measurements are supported by detailed numerical simulations using the inhouse CFD code TBLOCK. Experimental as well as numerical results congruently indicate a considerable reduction of the heat transfer coefficient (HTC) on the integrated vanes surfaces and endwalls caused by a differing state of boundary layer thickness. The studies furthermore depict a slight, non-detrimental shift in the heat transfer coefficient distributions and the strength of the integrated vanes secondary flows as a result of engine-realistic combustor swirl.

End-Wall Secondary Flow Control Using Engineered Residual Surface Structure

Residual surface roughness is often introduced in the manufacture process with ball-end or fillet-end milling. Instead of paying extra cost to remove these small-scale residual surface structures, there is a potential usage of them as flow control device. This numerical study therefore explores the ability of engineered surface structure in controlling the endwall secondary flow in turbomachinery. The CFD method is validated against the existing experimental data obtained for a 90 degree turning duct flow with a single rib fence placed on the end-wall. The working principle of the engineered surface structure is revealed through detailed analysis on the flow produced by multiple small fences and grooves mimicking the residual surface. The results consistently show that addition of engineered residual structure on flow surface can effectively reduce the magnitude of stream-wise vorticity associated with secondary flow and alleviate its lift-off motion. In the end, a general working mechanism and design guideline for optimizing the residual structure are summarized.