Analysis and Optimization of a New Differentially Driven Cable Parallel Robot

2015 ◽  
Vol 7 (3) ◽  
Author(s):  
Hamed Khakpour ◽  
Lionel Birglen ◽  
Souheil-Antoine Tahan
Keyword(s):  
Kinematic Analysis ◽  
Design Methodology ◽  
Degrees Of Freedom ◽  
Parallel Robot ◽  
Cable Robot ◽  
Proper Design ◽  
Two Indices ◽  
Three Degrees Of Freedom ◽  
Cable Robots

In this paper, a new three degrees of freedom (DOF) differentially actuated cable parallel robot is proposed. This mechanism is driven by a prismatic actuator and three cable differentials. Through this design, the idea of using differentials in the structure of a spatial cable robot is investigated. Considering their particular properties, the kinematic analysis of the robot is presented. Then, two indices are defined to evaluate the workspaces of the robot. Using these indices, the robot is subsequently optimized. Finally, the performance of the optimized differentially driven robot is compared with fully actuated mechanisms. The results show that through a proper design methodology, the robot can have a larger workspace and better performance using differentials than the fully driven cable robots using the same number of actuators.

Kinematic analysis and design of a novel 6-degree of freedom parallel robot

2014 ◽  
Vol 229 (2) ◽  
pp. 291-303 ◽  
Author(s):  
DU Hui ◽  
GAO Feng ◽  
PAN Yang
Keyword(s):  
Set Theory ◽  
Kinematic Analysis ◽  
Parallel Mechanism ◽  
Design Methodology ◽  
Parallel Robot ◽  
End Effector ◽  
Analysis And Design ◽  
Velocity Models ◽  
Reachable Workspace ◽  
Rotational Motions

A novel 3-UP3R parallel mechanism with six degree of freedoms is proposed in this paper. One most important advantage of this mechanism is that the three translational and three rotational motions are partially decoupled: the end-effector position is only determined by three inputs, while the rotational angles are relative to all six inputs. The design methodology via GF set theory is brought out, using which the limb type can be determined. The mobility of the end-effector is analyzed. After that, the kinematic and velocity models are formulated. Then, workspace is studied, and since the robot is partially decoupled, the reachable workspace is also the dexterous workspace. In the end, both local and global performances are discussed using conditioning indexes. The experiment of real prototype shows that this mechanism works well and may be applied in many fields.

A Novel 3-DOF Parallel Robot and its Kinematic Analysis

2014 ◽  
Vol 607 ◽  
pp. 759-763
Author(s):  
Xiao Bo Liu ◽  
Xiao Dong Yuan ◽  
Xiao Feng Wei ◽  
Wei Ni
Keyword(s):  
Motion Control ◽  
Kinematic Analysis ◽  
Degrees Of Freedom ◽  
Parallel Robot ◽  
Degree Of Freedom ◽  
The Novel ◽  
Forward Displacement ◽  
Simulation Based ◽  
Simulation Results

This paper deals with the design and analysis of a novel and simple two-translation and one-rotation (3 degrees of freedom, 3-dof) mechanism for alignment. Firstly, degree of freedom of the parallel robot is solved based on the theory of screw. Secondly considering the demand of motion control, we have conducted the analysis on the 3-dof parallel robot, which includes inverse displacement, forward displacement, and simulation based on SolidWorks Motion. The simulation results indicate that the novel 3-dof robot is suitable for performing the required operations.

Experimental results for the flexible joint cable-suspended manipulator of ICaSbot

Robotica ◽  
2013 ◽  
Vol 31 (6) ◽  
pp. 887-904 ◽  
Author(s):  
M. H. Korayem ◽  
M. Bamdad ◽  
H. Tourajizadeh ◽  
A. H. Korayem ◽  
R. M. Zehtab ◽  
...  
Keyword(s):  
Degrees Of Freedom ◽  
Experimental Tests ◽  
Parallel Robot ◽  
Joint Space ◽  
End Effector ◽  
Flexible Joint ◽  
Cable Robot ◽  
Six Dof ◽  
And Control ◽  
Computed Torque

SUMMARYIn this paper, design, dynamic, and control of the motors of a spatial cable robot are presented considering flexibility of the joints. End-effector control in order to control all six spatial degrees of freedom (DOFs) of the system and motor control in order to control the joints flexibility are proposed here. Corresponding programing of its operation is done by formulating the kinematics and dynamics and also control of the robot. Considering the existence of gearboxes, flexibility of the joints is modeled in the feed-forward term of its controller to achieve better accuracy. A two sequential closed-loop strategy consisting of proportional derivative (PD) for linear actuators in joint space and computed torque method for nonlinear end-effector in Cartesian space is presented for further accuracy. Flexibility is estimated using modeling and simulation by MATLAB and SimDesigner. A prototype has been built and experimental tests have been done to verify the efficiency of the proposed modeling and controller as well as the effect of flexibility of the joints. The ICaSbot (IUST Cable-Suspended robot) is an under-constrained six-DOF parallel robot actuated by the aid of six suspended cables. An experimental test is conducted for the manufactured flexible joint cable robot of ICaSbot and the outputs of sensors are compared with simulation. The efficiency of the proposed schemes is demonstrated.

Kinematic Analysis of a Five-Legged Mobile Robot

2010 ◽  
Author(s):  
Muhammed R. Pac ◽  
Dan O. Popa
Keyword(s):  
Kinematic Analysis ◽  
Degrees Of Freedom ◽  
Parallel Robot ◽  
Parallel Robots ◽  
The Body ◽  
Legged Robots ◽  
Upper Body ◽  
Design Changes ◽  
Robot Performance ◽  
The Impact

Legged robots are more maneuverable, and can negotiate rough terrain much better than conventional locomotion using wheels. However, since the kinematic or dynamic analysis of such robots involves closed chains, it is typically more difficult to investigate the impact of design changes, such as the number, or the design of its legs, to robot performance. Most legged robots consist of 4 legs (quadrupeds) or 6 legs (hexapods). This paper discusses the kinematic analysis of an unconventional, symmetrical 5-legged robot with 2-DOF (Degrees Of Freedom) universal joints in each leg. The analysis was carried out in order to predict the mobility of the upper body platform, and investigate the number of robot actuators needed for mobility. The product of exponentials formulation with respect to the local coordinate frames is used to describe the twists of the joints. The analysis is based on the idea that the robot body platform along with the legs can be considered instantaneously as a parallel robot manipulating the ground. Hence, the analysis can be done using the Jacobian formulation of parallel robots. Simulation results confirm the mobility analysis that the robot can have at most 3-DOF for the body and that these freedoms are coupled rotations and translations in 3D space also with a dependence on the configuration of the robot.

A new parallel wrist using only revolute pairs: the 3-RUU wrist

Robotica ◽  
2001 ◽  
Vol 19 (3) ◽  
pp. 305-309 ◽  
Author(s):  
Raffaele Di Gregorio
Keyword(s):  
Explicit Form ◽  
Kinematic Analysis ◽  
Degrees Of Freedom ◽  
Geometric Errors ◽  
End Effector ◽  
Singular Configurations ◽  
Overconstrained Mechanisms ◽  
Three Degrees Of Freedom

Only one parallel wrist with three equal legs containing just revolute pairs has been already presented in the literature. This parallel wrist is overconstrained, i.e., it involves three degrees of freedom required to orientate the end effector by using repetitions of constraints. The overconstrained mechanisms have the drawback of jamming or undergoing high internal loads when geometric errors occur. This paper presents a new parallel wrist, named 3-RUU wrist. The 3-RUU wrist is not overconstrained. It has three equal legs just involving revolute pairs and actuators adjacent to the frame and uses an architecture (3-RUU) already employed to obtain manipulators that make the end effector translate. The 3-RUU wrist kinematic analysis is addressed. This analysis shows that the new parallel wrist can reach singular configurations (translation singularities) in which the spherical constraint between end effector and frame fails. The singularity condition that makes finding all the 3-RUU wrist singular configurations possible is written in explicit form and geometrically interpreted.

Dynamic Trajectory Planning for a Three Degrees-of-Freedom Cable-Driven Parallel Robot Using Quintic B-Splines

2020 ◽  
Vol 142 (7) ◽  
Author(s):  
Sen Qian ◽  
Kunlong Bao ◽  
Bin Zi ◽  
W. D. Zhu
Keyword(s):  
Trajectory Planning ◽  
Degrees Of Freedom ◽  
Parallel Robot ◽  
Planning Method ◽  
End Effector ◽  
B Spline ◽  
B Splines ◽  
Pick And Place ◽  
Two Factors ◽  
Three Degrees Of Freedom

Abstract This paper presents a new trajectory planning method based on the improved quintic B-splines curves for a three degrees-of-freedom (3-DOF) cable-driven parallel robot (CDPR). First, the conditions of positive cables’ tension are expressed in terms of the position and acceleration constraints of the end-effector. Then, an improved B-spline curve is introduced, which is employed for generating a pick-and-place path by interpolating a set of given via-points. Meanwhile, by expressing the position and acceleration of the end-effector in terms of the first and second derivatives of the improved B-spline, the cable tension constraints are described in the form of B-spline parameters. According to the properties of the defined pick-and-place path, the proposed motion profile is dominated by two factors: the time taken for the end-effector to pass through all the via-points and the ratio between the nodes of B-spline. The two factors are determined through multi-objective optimization based on the efficiency coefficient method. Finally, experimental results on a 3-DOF CDPR show that the improved B-spline exhibits overall superior behavior in terms of velocity, acceleration, and cables force compared with the traditional B-spline. The validity of the proposed trajectory planning method is proved through the experiments.

Workspace Analysis of a Three DOF Cable-Driven Mechanism

2009 ◽  
Vol 1 (4) ◽  
Author(s):  
Alireza Alikhani ◽  
Saeed Behzadipour ◽  
S. Ali Sadough Vanini ◽  
Aria Alasty
Keyword(s):  
Degrees Of Freedom ◽  
Large Scale ◽  
Parallel Robot ◽  
External Loading ◽  
Geometrical Shape ◽  
Geometrical Approach ◽  
Workspace Analysis ◽  
Tensile Forces ◽  
Rotational Motions ◽  
Three Degrees Of Freedom

A cable-driven mechanism based on the idea of BetaBot (2005, “A New Cable-Based Parallel Robot With Three Degrees of Freedom,” Multibody Syst. Dyn., 13, pp. 371–383) is analyzed and geometrical description of its workspace boundary is found. In this mechanism, the cable arrangement eliminates the rotational motions leaving the moving platform with three translational motions. The mechanism has potentials for large scale manipulation and robotics in harsh environments. A detailed analysis of the tensionable workspace of the mechanism is presented. The mechanism, in a tensionable position, can develop tensile forces in all cables to maintain its rigidity under arbitrary external loading. A set of conditions on the geometry of the mechanism is proposed for which the tensionable workspace becomes a well defined convex polyhedron. The geometrical shape of the workspace is then described and the tensionability of the mechanism inside the workspace is proved. The proof is quite general and based on a geometrical approach.

Six degrees of freedom parallel robots with C5 links

Robotica ◽  
1992 ◽  
Vol 10 (1) ◽  
pp. 35-44 ◽  
Author(s):  
Y. Amirat ◽  
F. Artigue ◽  
J. Pontnau
Keyword(s):  
Automotive Industry ◽  
Kinematic Analysis ◽  
Degrees Of Freedom ◽  
Parallel Architecture ◽  
Parallel Robot ◽  
Parallel Architectures ◽  
Parallel Robots ◽  
Left Hand ◽  
Six Degrees Of Freedom ◽  
Assembly Tasks

SummaryThis paper presents at first a static and kinematic analysis of closed chains mechanisms which permits to deduce different possible fully parallel architectures. Then we focus on a particular parallel architecture with C5 links designed to perform precise assembly tasks. A general modeling of this C5 parallel robot is presented. Two typical assembly tasks in the automotive industry are also proposed; the first one uses the C5 links parallel robot as a left-hand device, while the second one uses it as the terminal tool of a sequential manipulator.

Sign in / Sign up

Export Citation Format

Share Document