Effects of Physical and Sorption Properties of Desiccant Coating on Performance of Energy Wheels

2017 ◽  
Vol 139 (6) ◽  
Author(s):  
Farhad Fathieh ◽  
Majid Nezakat ◽  
Richard W. Evitts ◽  
Carey J. Simonson
Keyword(s):  
Particle Size ◽  
Specific Surface ◽  
Surface Area ◽  
Silica Gel ◽  
Specific Surface Area ◽  
Correlated Data ◽  
Small Scale ◽  
Pore Width ◽  
Humidity Response ◽  
Energy Wheels

Desiccant-coated energy wheels are rotary-air-to-air energy exchangers widely used in ventilation systems to reduce the energy consumption required in industrial environments and commercial buildings. In this study, the effects of silica gel microphysical properties, i.e., pore width (Pw), specific surface area (SA), and particle size (dp), on the moisture recovery efficiency (latent effectiveness) of energy wheels are investigated. Three silica gel samples with different particle size and pore width (55 μm–77 Å, 150 μm–63 Å, and 160 μm–115 Å) are selected to coat small-scale energy exchangers. The sorption performance of the exchangers is determined from their normalized humidity response to a step increase in the inlet humidity at different flow rates. The results demonstrate that the transient humidity response is mainly specified by the desiccant pore size distribution, specific surface area, and mass of the coating. The transient analytical model is used to calculate the latent effectiveness (ɛL) of the exchangers from the transient humidity response. It was found that the exchanger coated with the smallest pore width (63 Å) has the highest available surface area and the highest latent effectiveness. With almost the same particle size (dp = 150 μm and 160 μm), the latent effectiveness increases by 5% (at wheel speed 20 rpm and Re = 174) as the pore width reduces from 150 Å to 63 Å. Increasing the particle size from 55 μm to 150 μm with almost the identical pore width (Pw = 63 Å and 77 Å) results in a slight enhancement in the latent effectiveness. ɛL is also calculated for correlated data (Yoon–Nelson model) where the results agree within experimental uncertainty bounds.

Physical Properties Variability of Zinc Powders Obtained by Electrochemical Method

2021 ◽  
Vol 316 ◽  
pp. 689-693
Author(s):  
K.D. Naumov ◽  
V.G. Lobanov
Keyword(s):  
Particle Size ◽  
Specific Surface ◽  
Bulk Density ◽  
Surface Area ◽  
Specific Surface Area ◽  
Current Density ◽  
Zinc Concentration ◽  
Regulatory Change ◽  
Average Particle ◽  
Zinc Powders

The aim of this paper is to establish a regulatory change of zinc powders key physicochemical properties with varying electroextraction conditions. It was studied influence zinc concentration, alkali concentration and current density. Quantitative dependencies of zinc powders particle size and specific surface area from mentioned electroextraction parameters are shown. At increasing of zinc concentration, decreasing of NaOH concentration and decreasing of current density of powders particle size growth, correspondingly specific surface area is declined. It is indicated, that electrolytic zinc powders bulk density varies from 0.61 g/cm3 to 0.75 g/cm3 with a decrease of average particle size from 121 μm to 68 μm. In comparison, spherical powders bulk density used in various industries is currently 2.45-2.6 g/cm3. In all experiments, metal zinc content varied in the range of 91.1-92.5%, the rest - ZnO. To a greater extent, this indicator depends on powder washing quality from alkali and storage conditions.

scholarly journals Synthesis of Spherical Silica by Sol-Gel Method and Its Application as Catalyst Support

2011 ◽  
Vol 10 (2) ◽  
pp. 25
Author(s):  
Anirut Leksomboon ◽  
Bunjerd Jongsomjit
Keyword(s):  
Particle Size ◽  
Ethylene Glycol ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Sol Gel ◽  
Weight Ratio ◽  
Gel Method ◽  
Sol Gel Method ◽  
Spherical Silica

In this present study, the spherical silica support was synthesized from tetraethyloxysilane (TEOS), water, sodium hydroxide, ethylene glycol and n-dodecyltrimethyl ammonium bromide (C12TMABr). The particle size was controlled by variation of the ethylene glycol co-solvent weight ratio of a sol-gel method preparation in the range of 0.10 to 0.50. In addition, the particle size apparently increases with high weight ratio of co-solvent, but the particle size distribution was broader. The standard deviation of particle diameter is large when the co-solvent weight ratio is more than 0.35 and less than 0.15. However, the specific surface area was similar for all weight ratios ranging from 1000 to 1300 m2/g. The synthesized silica was spherical and has high specific surface area. The cobalt was impregnated onto the obtained silica to produce the cobalt catalyst used for CO2 hydrogenation.</

Influence of Powder Particle Size of Slurries on Mechanical Properties of Porous Hydroxyapatite Ceramics

2005 ◽  
Vol 284-286 ◽  
pp. 365-368 ◽  
Author(s):  
Yin Zhang ◽  
Yoshiyuki Yokogawa ◽  
Tetsuya Kameyama
Keyword(s):  
Particle Size ◽  
Flexural Strength ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Particle Sizes ◽  
Wet Milling ◽  
Median Particle Size ◽  
Powder Characteristics ◽  
Median Particle

The effect of different particle sizes on the flexural strength and microstructure of three different types of hydroxyapatite (HAp) powders was studied. The powder characteristics of laboratory synthesized HAp powder (Lab1 and Lab2) were obtained through a wet milling method, and the median particle size and the specific surface area of powders are different with the dryness period. The median particle sizes of Lab1 and Lab2 are 0.34 µm and 0.74 µm, and the specific surface areas of Lab1 and Lab2 are 38.01 m2/g and 19.77 m2/g. The commercial HAp had median particle size of 1.13 µm and specific surface area of 11.62m2/g. The different powder characteristics affected the slip characteristics, and the flexural strength and microstructure of the sintered porous HAp bodies are also different. The optimum value for the minimum viscosity in these present HAp slip with respect to its solid loading and the optimum amount of the deflocculant were investigated. The flexural strengths of the porous HAp ceramics prepared by heating at 1200°C for 3 hrs in air were 17.59 MPa for Lab1 with a porosity of 60.48％, 10.51 MPa for Lab2 with a porosity of 57.75％, and 3.92 MPa for commercial HAp with a porosity of 79.37％.

Study on Comparison among Papermaking Powder Properties

2012 ◽  
Vol 512-515 ◽  
pp. 2434-2438
Author(s):  
Quan Xiao Liu ◽  
Wen Cai Xu
Keyword(s):  
Particle Size ◽  
Chemical Composition ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Preparation Method ◽  
Powder Properties

In this paper the comparison among some papermaking powder properties are studied. It shows that the properties of different powders are different because of different chemical composition and different preparation method and their particle size is different for different purpose such as filler and pigment. The particle size of powder for pigment powder is smaller than that for filler. The specific surface area of papermaking filler is lower than 20m2/g, the absorption value of DBP is about 45cm3/100g, the whiteness is up to 90%, and the particle size is about 3µm. The specific surface area of papermaking pigment is lower than 25m2/g, the absorption value of DBP is from 40 cm3/100g to100cm3/100g, the whiteness of clay is up to 50%, the whiteness of GCC and PCC is up to 90%, and the particle size is lower than 2µm. The specific surface area of silica is up to 100m2/g, the absorption value of DBP is up to 100cm3/100g, the whiteness is up to 97%, and the particle size is around 5µm.

Changes in Particle Size and Crystallinity in Ground Nickel Powder

2008 ◽  
Vol 587-588 ◽  
pp. 468-472
Author(s):  
J.M. González ◽  
José A. Rodríguez ◽  
Enrique J. Herrera
Keyword(s):  
Particle Size ◽  
Specific Surface ◽  
Crystallite Size ◽  
Surface Area ◽  
Specific Surface Area ◽  
Nickel Powder ◽  
Milling Time ◽  
High Energy ◽  
Published Data ◽  
Average Particle

Nickel powder was dry-milled using a high-energy disc-oscillating mill. The average particle size increases and the specific surface area diminishes with milling time. Crystallite size decreases and microstrains increase, under the same conditions, as shown by X-ray analysis. At 120 min milling time, the crystallite size has a value of 17 nm, i.e., a nanostructured powder, with a perturbed lattice, is obtained. The above results have been compared with published data about the effects of milling on a ceramic powder. There is, in both cases, a general agreement concerning the changes produced in crystallite size. Nevertheless, opposite results are reached regarding particle size and specific surface area.

scholarly journals Microwave solvothermal synthesis and characterization of manganese-doped ZnO nanoparticles

2016 ◽  
Vol 7 ◽  
pp. 721-732 ◽  
Author(s):  
Jacek Wojnarowicz ◽  
Roman Mukhovskyi ◽  
Elzbieta Pietrzykowska ◽  
Sylwia Kusnieruk ◽  
Jan Mizeracki ◽  
...  
Keyword(s):  
Particle Size ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Solvothermal Synthesis ◽  
Web Application ◽  
Zinc Acetate Dihydrate ◽  
Average Particle Size ◽  
Average Particle ◽  
Sem Images

Mn-doped zinc oxide nanoparticles were prepared by using the microwave solvothermal synthesis (MSS) technique. The nanoparticles were produced from a solution of zinc acetate dihydrate and manganese(II) acetate tetrahydrate using ethylene glycol as solvent. The content of Mn2+ in Zn1− x Mn x O ranged from 1 to 25 mol %. The following properties of the nanostructures were investigated: skeleton density, specific surface area (SSA), phase purity (XRD), lattice parameters, dopant content, average particle size, crystallite size distribution, morphology. The average particle size of Zn1− x Mn x O was determined using Scherrer’s formula, the Nanopowder XRD Processor Demo web application and by converting the specific surface area results. X-ray diffraction of synthesized samples shows a single-phase wurtzite crystal structure of ZnO without any indication of additional phases. Spherical Zn1− x Mn x O particles were obtained with monocrystalline structure and average particle sizes from 17 to 30 nm depending on the content of dopant. SEM images showed an impact of the dopant concentration on the morphology of the nanoparticles.

Preparation and Particle Size Characterization of Cu Nanoparticles Prepared by Anodic Arc Plasma

2010 ◽  
Vol 92 ◽  
pp. 163-169
Author(s):  
Hong Xia Qiao ◽  
Zhi Qiang Wei ◽  
Ming Ru Zhou ◽  
Zhong Mao He
Keyword(s):  
Crystal Structure ◽  
Particle Size ◽  
Specific Surface ◽  
Size Distribution ◽  
Surface Area ◽  
Specific Surface Area ◽  
Average Particle Size ◽  
Spherical Shape ◽  
Average Particle ◽  
Uniform Size

Copper nanoparticles were successfully prepared in large scales by means of anodic arc discharging plasma method in inert atmosphere. The particle size, specific surface area, crystal structure and morphology of the samples were characterized by X-ray diffraction (XRD), BET equation, transmission electron microscopy (TEM) and the corresponding selected area electron diffraction (SAED). The experiment results indicate that the crystal structure of the samples is fcc structure as same as that of the bulk materials. The specific surface area is is 11 m2/g, with the particle size distribution ranging from 30 to 90 nm, the average particle size about 67nm obtained from TEM and confirmed from XRD and BET results. The nanoparticles have uniform size, higher purity, narrow size distribution and spherical shape can be prepared by this convenient and effective method.

Sign in / Sign up

Export Citation Format

Share Document