A Generalized Hypoid Gear Synthesized With Common Crown Rack Positioned Between Pinion and Gear Blanks

2017 ◽  
Vol 139 (8) ◽  
Author(s):  
Nogill Park
Keyword(s):  
Entire Range ◽  
Point Contact ◽  
Transmission Error ◽  
Gear Transmission ◽  
Speed Ratio ◽  
Neutral Position ◽  
Hypoid Gear ◽  
Hypoid Gears ◽  
Pressure Angle ◽  
The Common

A new hypoid gearing using a common crown rack is introduced. The proposed hypoid gear has no unloaded gear transmission error. The common crown rack is located at a neutral position between the pinion and gear blanks. An arbitrary generating surface inclined at a pressure angle is prescribed. The proposed hypoid gearing is in point contact, fulfilling a constant speed ratio along the curved line of action. The synthesis feasibility is numerically verified for the entire range of hypoid gears, including parallel-, intersecting-, and crossed-axis gear systems. The proposed hypoid gear is compared with the hypoid gear by Gleason method and the differences between the two are discussed.

Simulation and Experimental Measurement of the Transmission Error of Real Hypoid Gears Under Load

2000 ◽  
Vol 122 (1) ◽  
pp. 109-122 ◽  
Author(s):  
Claude Gosselin ◽  
Thierry Guertin ◽  
Didier Remond ◽  
Yves Jean
Keyword(s):  
Measurement Data ◽  
Simulation Models ◽  
Transmission Error ◽  
Contact Analysis ◽  
Hypoid Gear ◽  
Tooth Contact Analysis ◽  
Tooth Contact ◽  
Hypoid Gears ◽  
Loaded Tooth Contact Analysis ◽  
Analysis Models

The Transmission Error and Bearing Pattern of a gear set are fundamental aspects of its meshing behavior. To assess the validity of gear simulation models, the Transmission Error and Bearing Pattern of a Formate Hypoid gear set are measured under a variety of operating positions and applied loads. Measurement data are compared to simulation results of Tooth Contact Analysis and Loaded Tooth Contact Analysis models, and show excellent agreement for the considered test gear set. [S1050-0472(00)00901-6]

Optimal Tooth Modifications in Hypoid Gears

2004 ◽  
Vol 127 (4) ◽  
pp. 646-655 ◽  
Author(s):  
Vilmos Simon
Keyword(s):  
Load Distribution ◽  
Angular Position ◽  
Point Contact ◽  
Tooth Surface ◽  
Gear Pair ◽  
Hypoid Gear ◽  
Tooth Contact ◽  
Hypoid Gears ◽  
Transmission Errors ◽  
Tool Profile

A method for the determination of optimal tooth modifications in hypoid gears based on improved load distribution and reduced transmission errors is presented. The modifications are introduced into the pinion tooth surface by using a cutter with bicircular profile and optimal diameter. In the optimization of tool parameters the influence of shaft misalignments of the mating members is included. As the result of these modifications a point contact of the meshed teeth surfaces appears instead of line contact; the hypoid gear pair becomes mismatched. By using the method presented in (Simon, V., 2000, “Load Distribution in Hypoid Gears,” ASME J. Mech. Des., 122, pp. 529–535) the influence of tooth modifications introduced on tooth contact and transmission errors is investigated. Based on the results that was obtained the radii and position of circular tool profile arcs and the diameter of the cutter for pinion teeth generation were optimized. By applying the optimal tool parameters, the maximum tooth contact pressure is reduced by 16.22% and the angular position error of the driven gear by 178.72%, in regard to the hypoid gear pair with a pinion manufactured by a cutter of straight-sided profile and of diameter determined by the commonly used methods.

Optimal Tooth Modifications in Hypoid Gears

2003 ◽  
Author(s):  
Vilmos V. Simon
Keyword(s):  
Angular Position ◽  
Point Contact ◽  
Tooth Surface ◽  
Gear Pair ◽  
Hypoid Gear ◽  
Tooth Contact ◽  
Hypoid Gears ◽  
Transmission Errors ◽  
Tool Profile

A method for the determination of optimal tooth modifications in hypoid gears based on improved load distribution and reduced transmission errors is presented. The modifications are introduced into the pinion tooth surface by using a cutter with bicircular profile and by changing the cutter diameter. In the optimization of tool parameters the influence of shaft misalignments of the mating members is included. As the result of these modifications a point contact of the meshed teeth surfaces appears instead of line contact; the hypoid gear pair becomes mismatched. By using the method presented in [1] the influence of tooth modifications introduced on tooth contact and transmission errors is investigated. Based on the results that was obtained the radii and position of circular tool profile arcs and the cutter diameter for pinion teeth generation were optimized. By applying the optimal tool parameters, the maximum tooth contact pressure is reduced by 16.22% and the angular position error of the driven gear by 178.72%, in regard to the hypoid gear pair with a pinion manufactured by a cutter of straight-sided profile and of diameter determined by the commonly used methods.

scholarly journals Multiphysics Investigations on the Dynamics of Differential Hypoid Gears

2014 ◽  
Vol 136 (4) ◽  
Author(s):  
M. Mohammadpour ◽  
S. Theodossiades ◽  
H. Rahnejat
Keyword(s):  
Multiscale Analysis ◽  
Point Contact ◽  
Elastohydrodynamic Lubrication ◽  
Transmission Efficiency ◽  
Operating Conditions ◽  
Hypoid Gear ◽  
Tooth Contact Analysis ◽  
Hypoid Gears ◽  
Gear Teeth ◽  
Noise Vibration

Vehicular differential hypoid gears play an important role on the noise, vibration, and harshness (NVH) signature of the drivetrain system. Additionally, the generated friction between their mating teeth flanks under varying load-speed conditions is a source of power loss in a drivetrain while absorbing some of the vibration energy. This paper deals with the coupling between system dynamics and analytical tribology in multiphysics, multiscale analysis. Elastohydrodynamic lubrication (EHL) of elliptical point contact of partially conforming hypoid gear teeth pairs with non-Newtonian thermal shear of a thin lubricant film is considered, including boundary friction as the result of asperity interactions on the contiguous surfaces. Tooth contact analysis (TCA) has been used to obtain the input data required for such an analysis. The dynamic behavior and frictional losses of a differential hypoid gear pair under realistic operating conditions are therefore determined. The detailed analysis shows a strong link between NVH refinement and transmission efficiency, a finding not hitherto reported in literature.

Optimization of Hypoid Gear Design and Tooth Contact Analysis

2017 ◽  
Author(s):  
Shouli Sun ◽  
Shilong Wang ◽  
Yawen Wang ◽  
Teik C. Lim ◽  
Baocang Zhou ◽  
...  
Keyword(s):  
Maximum Principle ◽  
Predictive Accuracy ◽  
Systems Design ◽  
Transmission Error ◽  
Design Parameters ◽  
Hypoid Gear ◽  
Normal Contact Stress ◽  
Normal Contact ◽  
Hypoid Gears ◽  
Peak Transmission

Hypoid gears are effectively used in cross axis power transmission systems. Design of hypoid gear parameters is complex and dependent on designers’ experiences. In this paper, an easy approach to design the parameters of hypoid gear to obtain the minimum of maximum principle normal contact stress and peak to peak transmission error is presented. An improved Particle Swarm Optimization (PSO) and Back Propagation (BP) algorithm is proposed to predict the stress and the transmission error if certain design parameters are given. The predictive accuracy is evaluated by Root Mean Square Error (RMSE) equation. The results show that the predictive accuracy is in reasonable agreement with the values calculated by the software [1]. Based on the prediction model, the optimization model for the design parameters of hypoid gear is established. This paper proposes a method to design a set of hypoid gears with minimum of maximum principle normal stress and peak to peak transmission error.

Generation of Hypoid Gears on CNC Hypoid Generator

2011 ◽  
Vol 133 (12) ◽  
Author(s):  
Vilmos V. Simon
Keyword(s):  
Gear Tooth ◽  
Velocity Ratio ◽  
Transmission Error ◽  
Tooth Surface ◽  
Polynomial Functions ◽  
Gear Pair ◽  
Hypoid Gear ◽  
Kinematic Scheme ◽  
Hypoid Gears ◽  
Fifth Order

In this study, polynomial functions of orders up to five are applied to induce variations in the cradle radial setting and the velocity ratio in the kinematic scheme of the machine tool for the generation of the pinion tooth surfaces corresponding to reduced transmission error amplitudes of a hypoid gear pair. The new CNC hypoid generators have made it possible to perform this nonlinear correction motions for the cutting of the face-milled hypoid gears. An algorithm is developed for the execution of motions on the CNC hypoid generator for the generation of face-milled hypoid gear tooth surface, based on the machine tool setting variation on the cradle-type hypoid generator induced by the optimal polynomial functions up to fifth-order. By using the corresponding computer program, the motion graphs of the CNC hypoid generator are determined for the generation of hypoid gear tooth surface, based on the optimal variation in the velocity ratio in the kinematic scheme and on the variation in the cradle radial setting on a cradle-type generator. The results presented indicate that the variation of the velocity ratio in the kinematic scheme of the hypoid generator induced by a fifth-order polynomial function resulted in a 62% reduction of the maximum transmission error of the gear pair.

scholarly journals Tribo-Dynamics of Differential Hypoid Gears

2013 ◽  
Author(s):  
Mahdi Mohammadpour ◽  
Stephanos Theodossiades ◽  
Homer Rahnejat
Keyword(s):  
Vibrational Energy ◽  
Point Contact ◽  
Elastohydrodynamic Lubrication ◽  
Operating Conditions ◽  
Hypoid Gear ◽  
Tooth Contact Analysis ◽  
Hypoid Gears ◽  
Dynamic Framework ◽  
Parametric Studies ◽  
Noise Vibration

Differential hypoid gears play an important role on the Noise, Vibration and Harshness (NVH) signature of vehicles. Additionally, friction developed between their teeth flanks under extreme loading conditions adds another source of power loss in the drivetrain which can mitigate vibrational energy. The paper considers the coupling between dynamics and analytical tribology to study dynamic response of hypoid gear pairs with lateral motion of support shafts also included in the analysis framework. Friction of teeth flank pairs is assumed to follow elastohydrodynamic lubrication under elliptical point contact geometry with lubricant film behavior conforming to Non-Newtonian thermal shear, also with surface asperity interactions. Tooth Contact Analysis (TCA) has been used to obtain the input data required for the investigation. The dynamic behavior and efficiency of a differential hypoid gear pair under realistic operating conditions is determined. The proposed tribo-dynamic framework provides a useful platform to conduct an extensive series of parametric studies.

Cutter Interchangeability for Spiral-Bevel and Hypoid Gear Manufacturing

2003 ◽  
Author(s):  
Claude Gosselin ◽  
Jack Masseth ◽  
Wei Liang
Keyword(s):  
Test Case ◽  
Hypoid Gear ◽  
Hypoid Gears ◽  
Manufacturing Operations ◽  
Before And After ◽  
Gear Manufacturing ◽  
Spiral Bevel ◽  
Tooth Flank ◽  
Tooth Flank Surface Topography ◽  
Flank Surface

In the manufacturing of spiral-bevel and hypoid gears, circular cutter dimensions are usually based on the desired performance of a gear set. In large manufacturing operations, where several hundred gear geometries may have been cut over the years, the necessary cutter inventory may become quite large since the cutter diameters will differ from one geometry to another, which results in used storage space and associated costs in purchasing and maintaining the cutter parts. Interchangeability of cutters is therefore of significant interest to reduce cost while maintaining approved tooth geometries. An algorithm is presented which allows the use of a different cutter, either in diameter and/or pressure angle, to obtain the same tooth flank surface topography. A test case is presented to illustrate the usefulness of the method: the OB cutter diameter of an hypoid pinion is changed from 8.9500" to 9.1000". CMM results and the comparison of the bearing patterns before and after change show excellent correlation, and indicate that the new pinion can be used in place of the original pinion without performance or quality problems. Significant cost reductions may be obtained with the application of the method.

Influence of the backlash generated by tooth accumulated wear on dynamic behavior of compound planetary gear set

2016 ◽  
Vol 231 (11) ◽  
pp. 2025-2041 ◽  
Author(s):  
Shijing Wu ◽  
Haibo Zhang ◽  
Xiaosun Wang ◽  
Zeming Peng ◽  
Kangkang Yang ◽  
...  
Keyword(s):  
Dynamic Response ◽  
Dynamic Model ◽  
Dynamic Behavior ◽  
Planetary Gear ◽  
Tooth Wear ◽  
Transmission Error ◽  
Gear Transmission ◽  
Tooth Surface ◽  
Contact Ratio ◽  
The Impact

Backlash is a key internal excitation on the dynamic response of planetary gear transmission. After the gear transmission running for a long time under load torque, due to tooth wear accumulation, the backlash between the tooth surface of two mating gears increases, which results in a larger and irregular backlash. However, the increasing backlash generated by tooth accumulated wear is generally neglected in lots of dynamics analysis for epicyclic gear trains. In order to investigate the impact of backlash generated by tooth accumulated wear on dynamic behavior of compound planetary gear set, in this work, first a static tooth surface wear prediction model is incorporated with a dynamic iteration methodology to get the increasing backlash generated by tooth accumulated wear for one pair of mating teeth under the condition that contact ratio equals to one. Then in order to introduce the tooth accumulated wear into dynamic model of compound planetary gear set, the backlash excitation generated by tooth accumulated wear for each meshing pair in compound planetary gear set is given under the condition that contact ratio equals to one and does not equal to one. Last, in order to investigate the impact of the increasing backlash generated by tooth accumulated wear on dynamic response of compound planetary gear set, a nonlinear lumped-parameter dynamic model of compound planetary gear set is employed to describe the dynamic relationships of gear transmission under the internal excitations generated by worn profile, meshing stiffness, transmission error, and backlash. The results indicate that the introduction of the increasing backlash generated by tooth accumulated wear makes a significant influence on the bifurcation and chaotic characteristics, dynamic response in time domain, and load sharing behavior of compound planetary gear set.

Gear transmission error outside the normal path of contact due to corner and top contact

1999 ◽  
Vol 213 (4) ◽  
pp. 389-400 ◽  
Author(s):  
R. G. Munro ◽  
L Morrish ◽  
D Palmer
Keyword(s):  
Dynamic Test ◽  
Theoretical Models ◽  
Transmission Error ◽  
Helical Gear ◽  
Gear Transmission ◽  
The Novel ◽  
Transmission Systems ◽  
Helical Gears ◽  
Tooth Stiffness ◽  
Top Contact

This paper is devoted to a phenomenon known as corner contact, or contact outside the normal path of contact, which can occur in spur and helical gear transmission systems under certain conditions. In this case, a change in position of the driven gear with respect to its theoretical position takes place, thus inducing a transmission error referred to here as the transmission error outside the normal path of contact (TEo.p.c). The paper deals with spur gears only, but the results are directly applicable to helical gears. It systematizes previous knowledge on this subject, suggests some further developments of the theory and introduces the novel phenomenon of top contact. The theoretical results are compared with experimental measurements using a single flank tester and a back-to-back dynamic test rig for spur and helical gears, and they are in good agreement. Convenient approximate equations for calculation of TEo.p.c suggested here are important for analysis of experimental data collected in the form of Harris maps. This will make possible the calculation of tooth stiffness values needed for use in theoretical models for spur and helical gear transmission systems.

Sign in / Sign up

Export Citation Format

Share Document