A Sensor System to Measure Force Applications of a Brace for Pectus carinatum

2018 ◽  
Vol 13 (1) ◽  
Author(s):  
Tomasz Bugajski ◽  
Douglas Kondro ◽  
Kartikeya Murari ◽  
Janet Ronsky
Keyword(s):  
Force Feedback ◽  
Force Measurement ◽  
Three Dimensional ◽  
Compressive Force ◽  
Current Treatment ◽  
Sensor System ◽  
Pectus Carinatum ◽  
Applied Forces ◽  
Human Participants ◽  
Force Measurement System

Pectus carinatum (PC) presents itself as a protrusion on the chest wall of adolescent individuals. Current treatment for PC is performed with a Pectus carinatum orthosis (PCO) that applies a compressive force to the protrusion. While this treatment is accepted, the magnitude of compressive forces applied remains unknown leading to excessive or deficient compression. Although the need for this quantitative data is recognized, no studies reporting the data or methods are available. The purpose of this study was to design an accurate force measurement system (FMS) that could be incorporated into a PCO with minimal bulk. Components of the FMS were three-dimensional (3D)-printed and incorporated into an existing PCO design. The FMS was calibrated using a custom indenter that applied forces to the FMS in a controlled manner. Evaluation of the FMS on five human participants was also performed. A reliability measure of the FMS was calculated for analysis. The FMS was implemented into the PCO and able to withstand the applied forces. The calibration revealed an increase in load cell error with increased magnitude of applied force (mean error [SD] = 5.59 N [6.48 N]). Participants recruited to evaluate the FMS demonstrated reliable forces (R = 96%) with smaller standard deviations than those during the calibration. The FMS was shown capable of measuring PCO forces but requires further testing and improvement. This system is the foundational component in a wireless, minimalistic sensor system to provide real time force feedback to both the clinician and patient.

Measurement of Skier-Generated Forces during Roller-Ski Skating

1995 ◽  
Vol 11 (3) ◽  
pp. 245-256 ◽  
Author(s):  
Glenn M. Street ◽  
Edward C. Frederick
Keyword(s):  
Force Measurement ◽  
Three Dimensional ◽  
Axial Loading ◽  
Three Dimensions ◽  
Calibration Data ◽  
Force Transducers ◽  
Sample Data ◽  
Reaction Forces ◽  
The Right ◽  
Force Measurement System

This paper describes a system that was developed to measure ski pole and roller-ski reaction forces in three dimensions during roller-ski skating. Uni-axial force transducers mounted in the right and left ski poles measure axial loading of the poles. Six transducers in one roller-ski measure biaxial loads beneath the foot. A remote computer stores the amplified transducer signals transmitted from the skier through 100 m cables. Three-dimensional video-graphy determines the orientations of the poles and roller-ski in order to resolve the resultant poling and skating forces into three components. Calibration data suggest that the resolution of the force measurement system is ±3 to 9% of the actual poling and skating forces, respectively. Sample data are presented from a VI skating trial during roller-skiing. These data provide the first glimpse at the major functions of the upper and lower body during roller-ski skating and show how the tool could be used to examine the size and effectiveness of skier-generated forces.

scholarly journals Design and Calibration of a Tri-Directional Contact Force Measurement System

2021 ◽  
Vol 11 (2) ◽  
pp. 877
Author(s):  
Rizwan Ahmed ◽  
Christian Maria Firrone ◽  
Stefano Zucca
Keyword(s):  
Contact Force ◽  
Measurement System ◽  
Force Measurement ◽  
Three Dimensional ◽  
Dynamic Contact ◽  
Forced Response ◽  
Contact Forces ◽  
Blade Vibration ◽  
Contact Models ◽  
Force Measurement System

In low pressure turbine stages, adjacent blades are coupled to each other at their tip by covers, called shrouds. Three-dimensional periodic contact forces at shrouds strongly affect the blade vibration level as energy is dissipated by friction. To validate contact models developed for the prediction of nonlinear forced response of shrouded blades, direct contact force measurement during dynamic tests is mandatory. In case of shrouded blades, the existing unidirectional and bi-directional contact force measurement methods need to be improved and extended to a tri-directional measurement of shroud contact forces for a comprehensive and more reliable validation of the shroud contact models. This demands an accurate and robust measurement solution that is compatible with the nature and orientation of the contact forces at blade shrouds. This study presents a cost effective and adaptable tri-directional force measurement system to measure static and dynamic contact forces simultaneously in three directions at blade shrouds during forced response tests. The system is based on three orthogonal force transducers connected to a reference block that will eventually be put in contact with the blade shroud in the test rig. A calibration process is outlined to define a decoupling matrix and its subsequent validation is demonstrated in order to evaluate the effectiveness of the measurement system to measure the actual contact forces acting on the contact.

scholarly journals The influence of craniofacial form on bite force and EMG activity of the masticatory muscles. II. The three-dimensional bite force measurement system.

1991 ◽  
Vol 35 (2) ◽  
pp. 366-380
Author(s):  
Toshimitsu Iinuma ◽  
Nobuhito Gionhaku ◽  
Yoshihiko Moriya ◽  
Koji Takeuchi ◽  
Hideaki Takeuchi ◽  
...  
Keyword(s):  
Measurement System ◽  
Force Measurement ◽  
Three Dimensional ◽  
Masticatory Muscles ◽  
Bite Force ◽  
Emg Activity ◽  
Force Measurement System

Finite Element Modeling for Steel Cord Analysis in Radial Tires

2013 ◽  
Vol 41 (1) ◽  
pp. 60-79 ◽  
Author(s):  
Wei Yintao ◽  
Luo Yiwen ◽  
Miao Yiming ◽  
Chai Delong ◽  
Feng Xijin
Keyword(s):  
Finite Element ◽  
High Efficiency ◽  
Force Measurement ◽  
Three Dimensional ◽  
Local Stress ◽  
Tension Force ◽  
Center Line ◽  
Element Analysis ◽  
Design Variables ◽  
Steel Cord

ABSTRACT: This article focuses on steel cord deformation and force investigation within heavy-duty radial tires. Typical bending deformation and tension force distributions of steel reinforcement within a truck bus radial (TBR) tire have been obtained, and they provide useful input for the local scale modeling of the steel cord. The three-dimensional carpet plots of the cord force distribution within a TBR tire are presented. The carcass-bending curvature is derived from the deformation of the carcass center line. A high-efficiency modeling approach for layered multistrand cord structures has been developed that uses cord design variables such as lay angle, lay length, and radius of the strand center line as input. Several types of steel cord have been modeled using the developed method as an example. The pure tension for two cords and the combined tension bending under various loading conditions relevant to tire deformation have been simulated by a finite element analysis (FEA). Good agreement has been found between experimental and FEA-determined tension force-displacement curves, and the characteristic structural and plastic deformation phases have been revealed by the FE simulation. Furthermore, some interesting local stress and deformation patterns under combined tension and bending are found that have not been previously reported. In addition, an experimental cord force measurement approach is included in this article.

scholarly journals An fMRI-compatible force measurement system for the evaluation of the neural correlates of step initiation

2017 ◽  
Vol 7 (1) ◽  
Author(s):  
Andrea Cristina de Lima-Pardini ◽  
Raymundo Machado de Azevedo Neto ◽  
Daniel Boari Coelho ◽  
Catarina Costa Boffino ◽  
Sukhwinder S. Shergill ◽  
...  
Keyword(s):  
Measurement System ◽  
Force Measurement ◽  
Neural Correlates ◽  
Step Initiation ◽  
Force Measurement System

scholarly journals A Magnetorheological Fluids-Based Robot-Assisted Catheter/Guidewire Surgery System for Endovascular Catheterization

Micromachines ◽  
2021 ◽  
Vol 12 (6) ◽  
pp. 640
Author(s):  
Linshuai Zhang ◽  
Shuoxin Gu ◽  
Shuxiang Guo ◽  
Takashi Tamiya
Keyword(s):  
Collision Detection ◽  
Endovascular Procedures ◽  
Force Feedback ◽  
Force Measurement ◽  
Occupational Hazards ◽  
Robot Assisted ◽  
X Ray ◽  
Surgical Safety ◽  
Surgical Tool ◽  
Haptic Cues

A teleoperated robotic catheter operating system is a solution to avoid occupational hazards caused by repeated exposure radiation of the surgeon to X-ray during the endovascular procedures. However, inadequate force feedback and collision detection while teleoperating surgical tools elevate the risk of endovascular procedures. Moreover, surgeons cannot control the force of the catheter/guidewire within a proper range, and thus the risk of blood vessel damage will increase. In this paper, a magnetorheological fluid (MR)-based robot-assisted catheter/guidewire surgery system has been developed, which uses the surgeon’s natural manipulation skills acquired through experience and uses haptic cues to generate collision detection to ensure surgical safety. We present tests for the performance evaluation regarding the teleoperation, the force measurement, and the collision detection with haptic cues. Results show that the system can track the desired position of the surgical tool and detect the relevant force event at the catheter. In addition, this method can more readily enable surgeons to distinguish whether the proximal force exceeds or meets the safety threshold of blood vessels.

Design and Development on Piezoelectric Ceramic Type Insole 3D Force Measurement System Based on LabVIEW

2011 ◽  
Vol 383-390 ◽  
pp. 774-779
Author(s):  
Ye Min Guo ◽  
Lan Mei Wang ◽  
Rui Yong Xue
Keyword(s):  
Shear Stress ◽  
Measurement System ◽  
Plantar Pressure ◽  
Piezoelectric Ceramic ◽  
Force Measurement ◽  
Stress System ◽  
Scientific Methods ◽  
Lab View ◽  
Design Requirements ◽  
Force Measurement System

According to the requirements of measurement of plantar pressure and shear stress in the meantime, this thesis puts forward a plan to construct a new insole plantar pressure and shear stress system based on multifunction data acquisition modular and Lab VIEW. Then the hardware part and software part are designed and developed respectively. There are 3 sensors are arrayed at each measurement point, that means 3 sensors are assembled in 3 different directions of X,Y and Z . The piezoelectric ceramic type sensors are designed, manufactured and calibrated according to scientific methods. Meanwhile, the DAQ card is selected carefully. Of course, the software part is developed based on Lab VIEW. A series of tests are performed in order to validate the function of the measurement system. The results satisfy the anticipated design requirements. At last, the problems and application trend of the measurement system are predicted.

Sign in / Sign up

Export Citation Format

Share Document