Numerical Investigation of a Vertical Axis Wind Turbine Performance Characterization Using New Variable Pitch Control Scheme

2019 ◽  
Vol 142 (3) ◽  
Author(s):  
Amin A. Mohammed ◽  
Ahmet Z. Sahin ◽  
Hassen M. Ouakad
Keyword(s):  
Wind Turbine ◽  
Pitch Angle ◽  
Numerical Study ◽  
Average Power ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Small Scale ◽  
Vertical Axis Wind Turbine ◽  
Variable Pitch ◽  
De Algorithm

Abstract A double multiple streamtube model coupled with variable pitch methodology is used to analyze the performance characteristics of a small-scale straight-bladed Darrieus type vertical axis wind turbine (SB-VAWT). The numerical study revealed that a fixed pitch of −2.5 deg could greatly enhance the performance of the wind turbine. However, no improvement is observed in the starting torque capacity. Furthermore, the performance of upwind and downwind zones has been investigated, and it is found that the VAWT starting capacity is improved by increasing/decreasing the pitch angle upwind/downwind of the turbine. To optimize the performance, four cases of variable pitch angle schemes of sinusoidal nature were examined. The parameters of the sinusoidal functions were optimized using differential evolution (DE) algorithm with different cost functions. The results showed improvement in the power coefficient, yet with low starting capacity enhancement. Among the objective functions used in DE algorithm, the negative of the average power coefficient is found to lead to the best starting capacity with moderate peak power coefficient.

Numerical Study of Pitch Angle on H-Type Vertical Axis Wind Turbine

2012 ◽  
Vol 499 ◽  
pp. 259-264
Author(s):  
Qi Yao ◽  
Ying Xue Yao ◽  
Liang Zhou ◽  
S.Y. Zheng
Keyword(s):  
Wind Turbine ◽  
Pitch Angle ◽  
Numerical Study ◽  
Vertical Axis ◽  
Azimuth Angle ◽  
Power Coefficient ◽  
Cfd Model ◽  
Vertical Axis Wind Turbine ◽  
Sliding Mesh ◽  
Mesh Technique

This paper presents a simulation study of an H-type vertical axis wind turbine. Two dimensional CFD model using sliding mesh technique was generated to help understand aerodynamics performance of this wind turbine. The effect of the pith angle on H-type vertical axis wind turbine was studied based on the computational model. As a result, this wind turbine could get the maximum power coefficient when pitch angle adjusted to a suited angle, furthermore, the effects of pitch angle and azimuth angle on single blade were investigated. The results will provide theoretical supports on study of variable pitch of wind turbine.

Computational fluid dynamic analysis of roof-mounted vertical-axis wind turbine with diffuser shroud, flange, and vanes

2018 ◽  
Vol 42 (4) ◽  
pp. 404-415
Author(s):  
H. Abu-Thuraia ◽  
C. Aygun ◽  
M. Paraschivoiu ◽  
M.A. Allard
Keyword(s):  
Wind Turbine ◽  
Urban Areas ◽  
Guide Vane ◽  
Fluid Dynamic ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Small Scale ◽  
Vertical Axis Wind Turbine ◽  
Guide Vanes ◽  
Turbine Design

Advances in wind power and tidal power have matured considerably to offer clean and sustainable energy alternatives. Nevertheless, distributed small-scale energy production from wind in urban areas has been disappointing because of very low efficiencies of the turbines. A novel wind turbine design — a seven-bladed Savonius vertical-axis wind turbine (VAWT) that is horizontally oriented inside a diffuser shroud and mounted on top of a building — has been shown to overcome the drawback of low efficiency. The objective this study was to analyze the performance of this novel wind turbine design for different wind directions and for different guide vanes placed at the entrance of the diffuser shroud. The flow field over the turbine and guide vanes was analyzed using computational fluid dynamics (CFD) on a 3D grid for multiple tip-speed ratios (TSRs). Four wind directions and three guide-vane angles were analyzed. The wind-direction analysis indicates that the power coefficient decreases to about half when the wind is oriented at 45° to the main axis of the turbine. The analysis of the guide vanes indicates a maximum power coefficient of 0.33 at a vane angle of 55°.

scholarly journals A Dynamic Rotor Vertical-Axis Wind Turbine with a Blade Transitioning Capability

Energies ◽  
2019 ◽  
Vol 12 (8) ◽  
pp. 1446 ◽  
Author(s):  
Elie Antar ◽  
Amne El Cheikh ◽  
Michel Elkhoury
Keyword(s):  
Wind Turbine ◽  
Average Power ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Optimized Design ◽  
Detached Eddy Simulation ◽  
Vertical Axis Wind Turbine ◽  
Eddy Simulation ◽  
Delayed Detached Eddy Simulation

This work presents an optimized design of a dynamic rotor vertical-axis wind turbine (DR VAWT) which maximizes the operational tip-speed ratio (TSR) range and the average power coefficient (Cp) value while maintaining a low cut-in wind velocity. The DR VAWT is capable of mimicking a Savonius rotor during the start-up phase and transitioning into a Darrieus one with increasing rotor radius at higher TSRs. The design exploits the fact that with increasing rotor radius, the TSR value increases, where the peak power coefficient is attained. A 2.5D improved delayed detached eddy simulation (IDDES) approach was adopted in order to optimize the dynamic rotor design, where results showed that the generated blades’ trajectories can be readily replicated by simple mechanisms in reality. A thorough sensitivity analysis was conducted on the generated optimized blades’ trajectories, where results showed that they were insensitive to values of the Reynolds number. The performance of the DR VAWT turbine with its blades following different trajectories was contrasted with the optimized turbine, where the influence of the blade pitch angle was highlighted. Moreover, a cross comparison between the performance of the proposed design and that of the hybrid Savonius–Darrieus one found in the literature was carefully made. Finally, the effect of airfoil thickness on the performance of the optimized DR VAWT was thoroughly analyzed.

scholarly journals Kinematics of a vertical axis wind turbine with a variable pitch angle

2018 ◽  
Author(s):  
Mateusz Jakubowski ◽  
Roman Starosta ◽  
Pawel Fritzkowski
Keyword(s):  
Wind Turbine ◽  
Pitch Angle ◽  
Vertical Axis ◽  
Vertical Axis Wind Turbine ◽  
Variable Pitch

Numerical Analysis of a Rooftop Vertical Axis Wind Turbine

2011 ◽  
Author(s):  
N. Cristobal Uzarraga-Rodriguez ◽  
A. Gallegos-Mun˜oz ◽  
J. Manuel Riesco A´vila
Keyword(s):  
Numerical Analysis ◽  
Wind Turbine ◽  
Numerical Study ◽  
Vertical Axis ◽  
Turbine Rotor ◽  
Aerodynamic Performance ◽  
Power Coefficient ◽  
Vertical Axis Wind Turbine ◽  
Sliding Mesh ◽  
Mesh Model

A numerical analysis of a rooftop vertical axis wind turbine (VAWT) for applications in urban area is presented. The numerical simulations were developed to study the flow field through the turbine rotor to analyze the aerodynamic performance characteristics of the device. Three different blade numbers of wind turbine are studied, 2, 3 and 4, respectively. Each one of the models was built in a 3D computational model. The effects generated in the performance of turbines by the numbers of blades are considered. A Sliding Mesh Model (SMM) capability was used to present the dimensionless form of coefficient power and coefficient moment of the wind turbine as a function of the wind velocity and the rotor rotational speed. The numerical study was developed in CFD using FLUENT®. The results show the aerodynamic performance for each configuration of wind turbine rotor. In the cases of Rooftop rotor the power coefficient increases as the blade number increases, while in the case of Savonius rotor the power coefficient decrease as the blades number increases.

scholarly journals Numerical analysis on the performance of Dual Rotor wind turbine

2020 ◽  
Vol 8 (03) ◽  
pp. 352-368
Author(s):  
Hazem Ali Abdel Karim ◽  
Ahmed Reda El-Baz ◽  
Nabil Abdel Aziz Mahmoud ◽  
Ashraf Mostafa Hamed
Keyword(s):  
Wind Turbine ◽  
Rotational Speed ◽  
Pitch Angle ◽  
Numerical Study ◽  
Three Dimensional ◽  
Scale Model ◽  
Power Coefficient ◽  
Peak Performance ◽  
Small Scale ◽  
Cfd Simulations

This study investigates the aerodynamic performance of wind turbines aiming to maximize the power extracted from the wind. The study is focusing on the effect of introducing a second rotor to the main rotor of the wind turbine in what is called a dual rotor wind turbine (DRWT).  The numerical study took place on the performance of small-scale model of wind turbine of 0.9 m diameter using S826 airfoil. Both the Co-rotating and Counter rotating configurations were investigated at different tip speed ratios (TSR) and compared with the performance of the single rotor wind turbine (SRWT). Many parameters were studied for dual rotor turbines. These include the spacing between the two rotors, the pitch angle of the rear rotor and the rotational speed of ratio rear to front rotor. Three-dimensional simulations performed and employed using CFD simulations with Multi Reference Frame (MRF) technique. The Co Rotating Wind Turbine (CWT) and Counter Rotating Wind Turbine (CRWT) found to have better performance compared to that of the SRWT with an increase ranging from 12 to 14% in peak power coefficient. Moreover, the effect of changing the pitch angle of the rear rotor on the overall performance found to be of a negligible effect between angles 0⁰ until 2⁰ degrees tilting toward the front rotor. On the other hand, the ratio of rotational speed of the rear rotor to the front rotor found to cause a further increase in the peak performance of the CWT and CRWT ranging from 3 to 5%.

Performance Improvements for a Vertical Axis Wind Turbine by Means of Gurney Flap

2019 ◽  
Vol 142 (2) ◽  
Author(s):  
Yan Yan ◽  
Eldad Avital ◽  
John Williams ◽  
Jiahuan Cui
Keyword(s):  
Wind Turbine ◽  
Stokes Equations ◽  
Numerical Study ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Navier Stokes ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Performance Improvements ◽  
Gurney Flap

Abstract A numerical study was carried out to investigate the effects of a Gurney flap (GF) on the aerodynamics performance of the NACA 00 aerofoil and an associated three-blade rotor of a H-type Darrieus wind turbine. The flow fields around a single aerofoil and the vertical axis wind turbine (VAWT) rotor are studied using unsteady Reynolds-averaged Navier–Stokes equations (URANS). The height of GF ranges from 1% to 5% of the aerofoil chord length. The results show that the GF can increase the lift and lift-to-drag ratio of the aerofoil as associated with the generation of additional vortices near the aerofoil trailing edge. As a result, adding a GF can significantly improve the power coefficient of the VAWT at low tip speed ratio (TSR), where it typically gives low power production. The causing mechanism is discussed in detail, pointing to flow separation and dynamic stall delay.

Influence of Fixed Pitch Angle on the Performance of Small Scale H-Darrieus

2016 ◽  
Author(s):  
Teresa Parra-Santos ◽  
Diego J. Palomar Trullen ◽  
Armando Gallegos ◽  
Cristobal N. Uzarraga ◽  
Maria Regidor-Sanchez ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Pitch Angle ◽  
Stokes Equations ◽  
Vertical Axis ◽  
Navier Stokes ◽  
Small Scale ◽  
Vertical Axis Wind Turbine ◽  
Sst Turbulence Model ◽  
Set Up ◽  
Fixed Pitch

The performance of a Vertical Axis Wind Turbine (VAWT) is numerically analyzed. Influence of fixed pitch angle is studied to get tendencies on the characteristic curves. The set up corresponds with an H-Darrieus with three straight NACA airfoils attached to a vertical shaft. Two-dimensional, transient, Navier Stokes equations are solved with a Third-Order Muscl scheme using SIMPLE to couple pressure and velocity. At least three revolutions must be simulated to get the periodic behaviour. Transition SST turbulence model has been chosen based on literature. Pitch angles of −6° and −10° have been analyzed with Tip Speed Ratios ranging from 0.7 and 1.6. The pitch angle of −10° improves the performance of the wind turbine. Instantaneous and averaged power coefficients as well as detailed flow field around the airfoils are shown.

scholarly journals NUMERICAL STUDY OF TWO VERTICAL AXIS WIND TURBINES DARRIEU TYPE LINED UP IN FUNCTION OF POWER COEFFICIENT1

2017 ◽  
Vol 6 (3) ◽  
Author(s):  
Rodrigo Spotorno Vieira ◽  
Luiz Alberto Oliveira Rocha ◽  
Liércio André Isoldi ◽  
Elizaldo Domingues Dos Santos
Keyword(s):  
Wind Turbine ◽  
Numerical Study ◽  
Mass Conservation ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Vertical Axis Wind Turbine ◽  
Worst Case ◽  
Study Power ◽  
Great Possibility ◽  
Volume Method

In this work is performed a numerical study of the main operational principle of a VAWT (Vertical Axis Wind turbine) and the influence of the distance between two aligned turbines over their power coefficient. The main aims here are to evaluate the applicability of the numerical model studied here in further optimization studies of VAWT and evaluate the effect of the distance between turbines (d) on the device power coefficient. To achieve these goals, it is considered an incompressible, transient and turbulent flow on a two dimensional domain with two fluid zones, one being rotational representing the rotation of the blades. The time-averaged mass conservation equations and momentum are numerically solved using the finite volume method, more precisely with the software FLUENTÒ. For the approach of turbulence is used to classical modeling of turbulence (RANS) with standard model k - ε. Other geometric parameters: turbine radius (R), the airfoil profile (NACA0018) and chorus were held constant. The verification results showed a good agreement with those presented in the literature, even employing a simplified domain. It was also observed that the distance (d) directly affects the power of the second turbine. For the best case, with d =10m, the downstream turbine showed an approximate 50% drop in power coefficient in comparison with that obtained for the upstream turbine. While in the worst case, with d =2m, the power coefficient for the downstream turbine decreased two hundred times in comparison with that achieved for the upstream one. It was also noted that there is a great possibility of disposal area optimization of turbines in future studies. Keywords: Vertical Axis Wind turbine, Numerical study, Power coefficient, turbine distance.

Sign in / Sign up

Export Citation Format

Share Document