Recognition of Structures Leading to Transition in a Low-Pressure Turbine Cascade: Effect of Reduced Frequency

2020 ◽  
Vol 142 (6) ◽  
Author(s):  
D. Lengani ◽  
D. Simoni ◽  
M. Ubaldi ◽  
P. Zunino ◽  
F. Bertini
Keyword(s):  
Boundary Layer ◽  
Suction Side ◽  
Low Pressure ◽  
Turbine Cascade ◽  
Turbulent Structures ◽  
Time Resolved ◽  
Low Pressure Turbine ◽  
Streaky Structures ◽  
Reduced Frequency ◽  
Displacement Thickness

Abstract The boundary layer developing over the suction side of a low-pressure turbine cascade operating under unsteady inflow conditions has been experimentally investigated. Time-resolved particle image velocimetry (PIV) measurements have been performed in two orthogonal planes, the blade-to-blade and a wall-parallel plane embedded within the boundary layer, for two different wake-reduced frequencies. Proper orthogonal decomposition (POD) has been used to analyze the data and to provide an interpretation of the most significant flow structures for each phase of the wake passing cycle. Detailed information on the most energetic turbulent structures at a particular phase is obtained with a newly developed procedure that overcomes the limit of classical phase average. The synchronization of the measurements in the two planes allows the computation of the characteristic dimension of boundary layer streaky structures that are responsible for transition. The largest and most energetic structures are observed when the wake centerline passes over the rear part of the suction side, and they appear practically the same for both reduced frequencies. The passing wake forces transition leading to the breakdown of the boundary layer streaks. Otherwise, the largest differences between the low and high reduced frequency are observed in the calmed region. The postprocessing of these two planes allowed computing the spacing of the streaky structures and making it nondimensional by the boundary layer displacement thickness observed for each phase. The nondimensional value of the streaks spacing is about constant, irrespective of the reduced frequency.

Recognition of Structures Leading to Transition in a Low Pressure Turbine Cascade: Effect of Reduced Frequency

2019 ◽  
Author(s):  
D. Lengani ◽  
D. Simoni ◽  
M. Ubaldi ◽  
P. Zunino ◽  
F. Bertini
Keyword(s):  
Boundary Layer ◽  
Suction Side ◽  
Low Pressure ◽  
Turbine Cascade ◽  
Turbulent Structures ◽  
Time Resolved ◽  
Low Pressure Turbine ◽  
Reduced Frequency ◽  
Displacement Thickness ◽  
Wake Passing

Abstract The boundary layer developing over the suction side of a low pressure turbine cascade operating under unsteady inflow conditions has been experimentally investigated. Time-resolved Particle Image Velocimetry (PIV) measurements have been performed in two orthogonal planes, the blade to blade and a wall parallel plane embedded within the boundary layer, for two different wake reduced frequencies. Proper Orthogonal Decomposition (POD) has been used to analyze the data and to provide an interpretation of the most significant flow structures for each phase of the wake passing cycle. To this purpose, a POD based procedure that sorts the data synchronizing the measurements of the two planes has been developed. Phase averaged data are then obtained for both cases. Moreover, once properly sorted, POD has been applied to sub-ensembles of data at the same relative phase within the wake passing cycle. Detailed information on the most energetic turbulent structures at a particular phase are obtained with this procedure (called phased POD), overcoming the limit of classical phase average that just provides a statistical representation of the turbulence field. Furthermore, the synchronization of the measurements in the two planes allows the computation of the characteristic dimension of boundary layer structures that are responsible for transition. These structures are often identified as vortical filaments parallel to the wall, typically referred to as boundary layer streaks. The largest and most energetic structures are observed when the wake centerline passes over the rear part of the suction side, and they appear practically the same for both reduced frequencies. The passing wake forces transition leading to the breakdown of the boundary layer streaks. Otherwise, the largest differences between the low and high reduced frequency are observed in the calmed region. The post-processing of these two planes further allowed us to compute the spacing of the streaks and make it non-dimensional by the boundary layer displacement thickness observed for each phase. The non-dimensional value of the streaks spacing is about constant, irrespective of the reduced frequency.

Numerical Investigation of Loss Development in a Low-Pressure Turbine Cascade With Unsteady Inflow and Varying Inlet Endwall Boundary Layer

2021 ◽  
Author(s):  
Tobias Schubert ◽  
Reinhard Niehuis
Keyword(s):  
Boundary Layer ◽  
Low Pressure ◽  
Turbine Cascade ◽  
Time Resolved ◽  
Blade Passage ◽  
Low Pressure Turbine ◽  
Wake Interaction ◽  
Spatial Redistribution ◽  
Unsteady Inflow ◽  
Flow Attenuation

Abstract An investigation of endwall loss development is conducted using the T106A low-pressure turbine cascade. (U)RANS simulations are complemented by measurements under engine relevant flow conditions (M2th = 0.59, Re2th = 2·105). The effects of unsteady inflow conditions and varying inlet endwall boundary layer are compared in terms of secondary flow attenuation downstream of the blade passage, analyzing steady, time-averaged, and time-resolved flow fields. While both measures show similar effects in the turbine exit plane, the upstream loss development throughout the blade passage is quite different. A variation of the endwall boundary layer alters the slope of the axial loss generation beginning around the midpoint of the blade passage. Periodically incoming wakes, however, cause a spatial redistribution of the loss generation with a premature loss increase due to wake interaction in the front part of the passage followed by an attenuation of the profile- and secondary loss generation in the aft section of the blade passage. Ultimately, this leads to a convergence of the downstream loss values in the steady and unsteady inflow cases.

Effects of Periodic Wakes and Freestream Turbulence on Coherent Structures in Low-Pressure Turbine Boundary Layer

2012 ◽  
Author(s):  
Weihao Zhang ◽  
Zhengping Zou ◽  
Kun Zhou ◽  
Huoxing Liu ◽  
Jian Ye
Keyword(s):  
Boundary Layer ◽  
Coherent Structures ◽  
Low Pressure ◽  
Turbine Cascade ◽  
Freestream Turbulence ◽  
High Lift ◽  
Low Pressure Turbine ◽  
Reduced Frequency ◽  
Large Eddy ◽  
Separation Bubbles

The effects of periodic wakes and inlet freestream turbulence intensity (FSTI) on coherent structures in the boundary layer of a high-lift low-pressure turbine cascade are studied in this paper. Large-eddy simulations (LES) are performed on T106D-EIZ profile at Reynolds number (Re) of 60,154 (based on the chord and outflow velocity). Eight cases, considering FSTI of 0, 2.5%, 5% and 10% as well as the wake reduced frequency (fr) of 0.67, 1.34 and 0.335, are conducted and discussed. The results show that the open separation could be compressed by freestream turbulence to a small extent, whereas, it could be replaced by separation bubbles under wake conditions. Stripe structures and turbulence spots appear in shear layer over the separation bubbles. The increments of wake frequency or FSTI can accelerate the transition progress which result in shorter separation bubbles, meanwhile, emphasize the turbulence spots.

Separated Flow Transition in a Low Pressure Turbine Cascade: Mean Flow and Turbulence Spectra

2003 ◽  
Author(s):  
Ralph J. Volino ◽  
Christopher G. Murawski
Keyword(s):  
Boundary Layer ◽  
Free Stream ◽  
Separation Bubble ◽  
Suction Side ◽  
Low Pressure ◽  
Turbine Cascade ◽  
Mean Flow ◽  
Turbulence Spectra ◽  
Free Stream Turbulence ◽  
Low Pressure Turbine

Boundary layer separation, transition and reattachment have been studied experimentally in a low-pressure turbine cascade. Cases with Reynolds numbers (Re) ranging from 50,000 to 200,000 (based on suction surface length and exit velocity) have been considered under low free-stream turbulence conditions. Mean and fluctuating velocity profiles and turbulence spectra are presented for streamwise locations along the suction side of one airfoil and in the wake downstream of the airfoils. Hot film gages on the suction side surface of the airfoil are used to measure the fluctuation level and the spectra of the fluctuations on the surface. Higher Re moves transition upstream. Transition is initiated in the shear layer over the separation bubble and leads to boundary layer reattachment. Peak frequencies in the boundary layer spectra match those found in similar cases in the literature, indicating that the important frequencies may be predictable. Spectra in the wake downstream of the airfoils were similar to the spectra in the boundary layer near the trailing edge of the airfoil. Comparisons to the literature indicate that small but measurable differences in the spectra of the low free-stream turbulence can have a significant effect on boundary layer reattachment.

The Effect of Pulsed Blowing on the Boundary Layer of a Highly Loaded Low Pressure Turbine Blade

2013 ◽  
Author(s):  
Marion Mack ◽  
Roland Brachmanski ◽  
Reinhard Niehuis
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Mach Number ◽  
Suction Side ◽  
Reynolds Numbers ◽  
Low Pressure ◽  
Trailing Edge ◽  
Low Pressure Turbine ◽  
Wide Range ◽  
Highly Loaded

The performance of the low pressure turbine (LPT) can vary appreciably, because this component operates under a wide range of Reynolds numbers. At higher Reynolds numbers, mid and aft loaded profiles have the advantage that transition of suction side boundary layer happens further downstream than at front loaded profiles, resulting in lower profile loss. At lower Reynolds numbers, aft loading of the blade can mean that if a suction side separation exists, it may remain open up to the trailing edge. This is especially the case when blade lift is increased via increased pitch to chord ratio. There is a trend in research towards exploring the effect of coupling boundary layer control with highly loaded turbine blades, in order to maximize performance over the full relevant Reynolds number range. In an earlier work, pulsed blowing with fluidic oscillators was shown to be effective in reducing the extent of the separated flow region and to significantly decrease the profile losses caused by separation over a wide range of Reynolds numbers. These experiments were carried out in the High-Speed Cascade Wind Tunnel of the German Federal Armed Forces University Munich, Germany, which allows to capture the effects of pulsed blowing at engine relevant conditions. The assumed control mechanism was the triggering of boundary layer transition by excitation of the Tollmien-Schlichting waves. The current work aims to gain further insight into the effects of pulsed blowing. It investigates the effect of a highly efficient configuration of pulsed blowing at a frequency of 9.5 kHz on the boundary layer at a Reynolds number of 70000 and exit Mach number of 0.6. The boundary layer profiles were measured at five positions between peak Mach number and the trailing edge with hot wire anemometry and pneumatic probes. Experiments were conducted with and without actuation under steady as well as periodically unsteady inflow conditions. The results show the development of the boundary layer and its interaction with incoming wakes. It is shown that pulsed blowing accelerates transition over the separation bubble and drastically reduces the boundary layer thickness.

The Effects of Inlet Boundary Layer Condition and Periodically Incoming Wakes on Secondary Flow in a Low Pressure Turbine Cascade

2020 ◽  
Author(s):  
Tobias Schubert ◽  
Silvio Chemnitz ◽  
Reinhard Niehuis
Keyword(s):  
Boundary Layer ◽  
Secondary Flow ◽  
High Speed ◽  
Low Pressure ◽  
Experimental Investigations ◽  
Turbine Cascade ◽  
Flow Conditions ◽  
Low Pressure Turbine ◽  
Speed Flow ◽  
Unsteady Inflow

Abstract A particular turbine cascade design is presented with the goal of providing a basis for high quality investigations of endwall flow at high-speed flow conditions and unsteady inflow. The key feature of the design is an integrated two-part flat plate serving as a cascade endwall at part-span, which enables a variation of the inlet endwall boundary layer conditions. The new design is applied to the T106A low pressure turbine cascade for endwall flow investigations in the High-Speed Cascade Wind Tunnel of the Institute of Jet Propulsion at the Bundeswehr University Munich. Measurements are conducted at realistic flow conditions (M2th = 0.59, Re2th = 2·105) in three cases of different endwall boundary layer conditions with and without periodically incoming wakes. The endwall boundary layer is characterized by 1D-CTA measurements upstream of the blade passage. Secondary flow is evaluated by Five-hole-probe measurements in the turbine exit flow. A strong similarity is found between the time-averaged effects of unsteady inflow conditions and the effects of changing inlet endwall boundary layer conditions regarding the attenuation of secondary flow. Furthermore, the experimental investigations show, that all design goals for the improved T106A cascade are met.

Blade–Row Interactions in a Low Pressure Turbine at Design and Strong Off-Design Operation

2014 ◽  
Vol 136 (11) ◽  
Author(s):  
Martin Lipfert ◽  
Jan Habermann ◽  
Martin G. Rose ◽  
Stephan Staudacher ◽  
Yavuz Guendogdu
Keyword(s):  
Experimental Data ◽  
Flow Field ◽  
Three Dimensional ◽  
Suction Side ◽  
Low Pressure ◽  
Test Facility ◽  
Time Resolved ◽  
Joint Project ◽  
Low Pressure Turbine ◽  
Blade Row

In a joint project between the Institute of Aircraft Propulsion Systems (ILA) and MTU Aero Engines, a two-stage low pressure turbine is tested at design and strong off-design conditions. The experimental data taken in the Altitude Test Facility (ATF) aims to study the effect of positive and negative incidence of the second stator vane. A detailed insight and understanding of the blade row interactions at these regimes is sought. Steady and time-resolved pressure measurements on the airfoil as well as inlet and outlet hot-film traverses at identical Reynolds number are performed for the midspan streamline. The results are compared with unsteady multistage computational fluid dynamics (CFD) predictions. Simulations agree well with the experimental data and allow detailed insights in the time-resolved flow-field. Airfoil pressure field responses are found to increase with positive incidence whereas at negative incidence the magnitude remains unchanged. Different pressure to suction side (SS) phasing is observed for the studied regimes. The assessment of unsteady blade forces reveals that changes in unsteady lift are minor compared to changes in axial force components. These increase with increasing positive incidence. The wake-interactions are predominating the blade responses in all regimes. For the positive incidence conditions, vane 1 passage vortex fluid is involved in the midspan passage interaction, leading to a more distorted three-dimensional (3D) flow field.

G604 Mesurements and Numerical Simulation of Blade Boundary Layer in a Low・Pressure Turbine Cascade for Aeroengine : Effects of Wake Passing(1)

2006 ◽  
Vol 2006 (0) ◽  
pp. _G604-a_
Author(s):  
Ken-ichi Funazaki ◽  
Kazutoyo Yamada ◽  
Mamoru Kikuchi ◽  
Takahiro Ono
Keyword(s):  
Numerical Simulation ◽  
Boundary Layer ◽  
Low Pressure ◽  
Turbine Cascade ◽  
Low Pressure Turbine ◽  
Wake Passing
Sign in / Sign up

Export Citation Format

Share Document