Modal and Forced Response Analysis of Vehicle Systems With Latent Vibration Modes Due to Hydraulic Mounts

2020 ◽  
Vol 142 (4) ◽  
Author(s):  
Hyeon Gyu Sakong ◽  
Gyunchul Hur ◽  
Kwang-Joon Kim ◽  
Wonju Jeon
Keyword(s):  
Degrees Of Freedom ◽  
Equations Of Motion ◽  
Time Domain Analysis ◽  
Hydraulic Modeling ◽  
Internal Variable ◽  
Forced Response ◽  
Response Analysis ◽  
Car Body ◽  
Modeling Approaches ◽  
Mechanical Mass

Abstract Hydraulic mounts used in vehicles for better isolation of vibrations were often approximated by lumped or mechanical mass-damper-spring (m-c-k) models, although deficiency in such modeling was pointed out and “hydraulic” modeling was proposed as an alternative. In this paper, a brief review on the mechanical m-c-k modeling and “hydraulic” modeling of the hydraulic mounts is presented. A simplest system consisting of a single mass and a hydraulic mount is used to illustrate both equivalence and difference in a closed form between the two modeling approaches. Then, modal analyses are done on an apparently three degrees-of-freedom (DOF) quarter car with a hydraulic mount, where the key idea is to use an internal variable for the movement of fluid mass which is responsible for a “latent” vibration mode. Equations of motion for the apparently 3DOF system, 4DOF system in fact, by the two modeling are formulated. Modal parameters by the proposed “hydraulic” modeling of the hydraulic mount are compared with those by the m-c-k modeling. Forced responses to transient base excitations are also compared between the two modeling approaches to illustrate how much errors can arise in the frequency and time domain analysis. To be more realistic, the modal and forced response analysis on a full car of an apparently 10DOF (3DOF for powertrain, 3DOF for car body, and 4DOF for knuckles and tires) with two more DOF internally for two hydraulic mounts between the powertrain and car body is presented.

Detection of Cracks in Mistuned Bladed Disks Using Reduced-Order Models and Vibration Data

2012 ◽  
Vol 134 (6) ◽  
Author(s):  
Chulwoo Jung ◽  
Akira Saito ◽  
Bogdan I. Epureanu
Keyword(s):  
Degrees Of Freedom ◽  
Dimensional Space ◽  
Equations Of Motion ◽  
Computational Cost ◽  
Three Dimensional ◽  
Cost Savings ◽  
Forced Response ◽  
Response Analysis ◽  
Reduced Order Models ◽  
Reduced Order

A novel methodology to detect the presence of a crack and to predict the nonlinear forced response of mistuned turbine engine rotors with a cracked blade and mistuning is developed. The combined effects of the crack and mistuning are modeled. First, a hybrid-interface method based on component mode synthesis is employed to develop reduced-order models (ROMs) of the tuned system with a cracked blade. Constraint modes are added to model the displacements due to the intermittent contact between the crack surfaces. The degrees of freedom (DOFs) on the crack surfaces are retained as active DOFs so that the physical forces due to the contact/interaction (in the three-dimensional space) can be accurately modeled. Next, the presence of mistuning in the tuned system with a cracked blade is modeled. Component mode mistuning is used to account for mistuning present in the uncracked blades while the cracked blade is considered as a reference (with no mistuning). Next, the resulting (reduced-order) nonlinear equations of motion are solved by applying an alternating frequency/time-domain method. Using these efficient ROMs in a forced response analysis, it is found that the new modeling approach provides significant computational cost savings, while ensuring good accuracy relative to full-order finite element analyses. Furthermore, the effects of the cracked blade on the mistuned system are investigated and used to detect statistically the presence of a crack and to identify which blade of a full bladed disk is cracked. In particular, it is shown that cracks can be distinguished from mistuning.

Detection of Cracks in Mistuned Bladed Disks Using Reduced Order Models and Vibration Data

2011 ◽  
Author(s):  
Chulwoo Jung ◽  
Akira Saito ◽  
Bogdan I. Epureanu
Keyword(s):  
Degrees Of Freedom ◽  
Dimensional Space ◽  
Equations Of Motion ◽  
Computational Cost ◽  
Three Dimensional ◽  
Cost Savings ◽  
Forced Response ◽  
Response Analysis ◽  
Reduced Order Models ◽  
Reduced Order

A novel methodology to detect the presence of a crack and to predict the nonlinear forced response of mistuned turbine engine rotors with a cracked blade and mistuning is developed. The combined effects of the crack and mistuning are modeled. First, a hybrid-interface method based on component mode synthesis is employed to develop reduced order models (ROMs) of the tuned system with a cracked blade. Constraint modes are added to model the displacements due to the intermittent contact between the crack surfaces. The degrees of freedom (DOFs) on the crack surfaces are retained as active DOFs so that the physical forces due to the contact/interaction (in the three-dimensional space) can be accurately modeled. Next, the presence of mistuning in the tuned system with a cracked blade is modeled. Component mode mistuning is used to account for mistuning present in the un-cracked blades while the cracked blade is considered as a reference (with no mistuning). Next, the resulting (reducedorder) nonlinear equations of motion are solved by applying an alternating frequency/time-domain method. Using these efficient ROMs in a forced response analysis, it is found that the new modeling approach provides significant computational cost savings, while ensuring good accuracy relative to full-order finite element analyses. Furthermore, the effects of the cracked blade on the mistuned system are investigated, and used to detect statistically the presence of a crack and to identify which blade of a full bladed disk is cracked. In particular, it is shown that cracks can be distinguished from mistuning.

Comparative Studies of Surrogate Models for Response Analysis of Mistuned Bladed Disks

2020 ◽  
Vol 17 (10) ◽  
pp. 2050012 ◽  
Author(s):  
Shiyuan Deng ◽  
Jianyao Yao ◽  
Linlin Wang ◽  
Jianqiang Xin ◽  
Ning Hu
Keyword(s):  
Degrees Of Freedom ◽  
Surrogate Models ◽  
Forced Response ◽  
Statistical Characteristics ◽  
Kriging Interpolation ◽  
Response Analysis ◽  
Bladed Disks ◽  
Single Output ◽  
Random Mistuning ◽  
Forced Responses

The forced responses of bladed disks are highly sensitive to inevitable random mistuning. Considerable computational efforts are required for the sampling process to assess the statistical vibration properties of mistuned bladed disks. Therefore, efficient surrogate models are preferred to accelerate the process for probabilistic analysis. In this paper, four surrogate models are utilized to construct the relation between random mistuning and forced response amplitudes, which are polynomial chaos expansion (PCE), response surface method (RSM), artificial neural networks (ANN) and Kriging interpolation, respectively. A bladed disk with 2-degrees-of-freedom (2-DOF) each sector is used to validate the effectiveness of the surrogate models. The effects of number of training samples on the surrogate model accuracy are discussed. The responses results of one blade (single output) and maximum response of all blades (multi-output) indicate that PCE and Kriging interpolation could yield accurate and stable predictions of the statistical characteristics of the forced responses. PCE is recommended for the mistuned response predictions due to its accuracy and efficiency.

An Efficient Response Analysis Method for a Non-Linear/Parameter Changing System Using Sub-Structure Modes

1993 ◽  
Vol 207 (1) ◽  
pp. 41-52
Author(s):  
H K Kim ◽  
Y-S Park
Keyword(s):  
Equations Of Motion ◽  
Forced Response ◽  
Suggested Method ◽  
Response Analysis ◽  
Synthesis Methods ◽  
Lumped Mass ◽  
State Equations ◽  
Mass Model ◽  
Non Linear ◽  
Forced Responses

An efficient state-space method is presented to determine time domain forced responses of a structure using the Lagrange multiplier based sub-structure technique. Compared with the conventional mode synthesis methods, the suggested method can be particularly effective for the forced response analysis of a structure subjected to parameter changes with time, such as a missile launch system, and/or having localized non-linearities, because this method does not need to construct the governing equations of the combined whole structure. Both the loaded interface free-free modes and free interface modes can be employed as the modal bases of each sub-structure. The sub-structure equations of motion are derived using Lagrange multipliers and recurrence discrete-time state equations based upon the concept of the state transition matrix are formulated for transient response analysis. The suggested method is tested with two example structures, a simple lumped mass model with a non-linear joint and an abruptly parameter changing structure. The test results show that the suggested method is very accurate and efficient in calculating forced responses and in comparing it with the direct numerical integration method.

Investigation of Damping Potential of Strip Damper on a Real Turbine Blade

2016 ◽  
Author(s):  
M. Afzal ◽  
I. Lopez Arteaga ◽  
L. Kari ◽  
V. Kharyton
Keyword(s):  
Boundary Conditions ◽  
Dynamic Properties ◽  
Equations Of Motion ◽  
Iterative Solution ◽  
Element Model ◽  
Forced Response ◽  
Contact Forces ◽  
Response Analysis ◽  
Bladed Disk ◽  
Different Types

This paper investigates the damping potential of strip dampers on a real turbine bladed disk. A 3D numerical friction contact model is used to compute the contact forces by means of the Alternate Frequency Time domain method. The Jacobian matrix required during the iterative solution is computed in parallel with the contact forces, by a quasi-analytical method. A finite element model of the strip dampers, that allows for an accurate description of their dynamic properties, is included in the steady-state forced response analysis of the bladed disk. Cyclic symmetry boundary conditions and the multiharmonic balance method are applied in the formulation of the equations of motion in the frequency domain. The nonlinear forced response analysis is performed with two different types of boundary conditions on the strip: (a) free-free and (b) elastic, and their influence is analyzed. The effect of the strip mass, thickness and the excitation levels on the forced response curve is investigated in detail.

On the Efficiency of Some Recently Developed Integration Algorithms for Offshore Problems

1983 ◽  
Vol 105 (1) ◽  
pp. 73-77 ◽  
Author(s):  
T. K. Datta ◽  
A. M. Sood
Keyword(s):  
Degrees Of Freedom ◽  
Large Time ◽  
Equations Of Motion ◽  
Iterative Solution ◽  
Response Analysis ◽  
Time Step ◽  
Beam Elements ◽  
Integration Schemes ◽  
Large Time Step ◽  
Integration Algorithms

The efficiency of some recently developed integration schemes, namely, Hilber’s ∝-method, collocation schemes and large time step integration schemes developed by Argyris, is evaluated by applying them to the response analysis of an idealized offshore tower. The tower is fixed at the base, having an additional mass at the top. For the analysis the tower has been modeled as an assemblage of 2-D beam elements. The dynamic degrees of freedom at each node are taken as those corresponding to the rotational and sway degrees of freedom. Using the normal mode theory the equations of motion have been decoupled except for the generalized loading vector which appear nonlinearly coupled, thus requiring iterative solution at every time step. The results of the study show that the large time step integration schemes developed by Argyris are more efficient than other integration methods considered here.

Dynamic Response Analysis of Large Latticed Space Structures

1989 ◽  
Vol 4 (1) ◽  
pp. 25-42 ◽  
Author(s):  
A.R. Kukreti ◽  
N.D. Uchil
Keyword(s):  
Dynamic Response ◽  
Degrees Of Freedom ◽  
Equations Of Motion ◽  
Computational Time ◽  
Space Structures ◽  
Response Analysis ◽  
Actual System ◽  
Large Space ◽  
Element Analysis ◽  
Dynamic Response Analysis

In this paper an alternative method for dynamic response analysis of large space structures is presented, for which conventional finite element analysis would require excessive computer storage and computational time. Latticed structures in which the height is very small in comparison to its overall length and width are considered. The method is based on the assumption that the structure can be embedded in its continuum, in which any fiber can translate and rotate without deforming. An appropriate kinematically admissable series function is constructed to descrbe the deformation of the middle plane of this continuum. The unknown coefficients in this function are called the degree-of-freedom of the continuum, which is given the name “super element.” Transformation matrices are developed to express the equations of motion of the actual systems in terms of the degrees-of-freedom of the super element. Thus, by changing the number of terms in the assumed function, the degrees-of-freedom of the super element can be increased or decreased. The super element response results are transformed back to obtain the desired response results of the actual system. The method is demonstrated for a structure woven in the shape of an Archimedian spiral.

A Case Study of the Unsteady Response of a Hingeless Helicopter Rotor Blade

2019 ◽  
Author(s):  
Pratik Sarker ◽  
Uttam K. Chakravarty
Keyword(s):  
Mathematical Model ◽  
Steady State ◽  
Rotor Blade ◽  
Degrees Of Freedom ◽  
Forced Response ◽  
Helicopter Rotor ◽  
Mode Shapes ◽  
Response Analysis ◽  
Steady State Condition ◽  
Helicopter Rotor Blade

Abstract The helicopter is an essential means of transport for numerous tasks including carrying passengers and equipment, providing air medical services, firefighting, and other military and civil tasks. While in operation, the nature of the unsteady aerodynamic environment surrounding the rotor blades gives rise to a significant amount of vibration to the helicopter. In this study, the unsteady forced response of the Bo 105 hingeless helicopter rotor blade is investigated at the forward flight in terms of the coupled flapping, lead-lag, and torsional deformations. The mathematical model for the steady-state response of the rotor blade is modified to include the unsteady airfoil behavior by using the Theodorsen’s lift deficiency function for three degrees of freedom of motion. The nonlinear mathematical model is solved by the generalized method of lines in terms of the time-varying deflections of the rotor blade. The unsteady airloads are found to create larger deformations compared to that of the steady-state condition for a given advance ratio. The azimuth locations of the peak loadings also vary with different degrees of freedom. The first three natural frequencies and mode shapes of the rotor blade are presented. The model for the forced response analysis is validated by finite element results.

Dynamic Analysis of a Motorized Spindle With Externally Pressurized Air Bearings

2015 ◽  
Vol 137 (4) ◽  
Author(s):  
Chundong Xu ◽  
Shuyun Jiang
Keyword(s):  
Dynamic Characteristics ◽  
Degrees Of Freedom ◽  
Equations Of Motion ◽  
Forced Response ◽  
Air Bearings ◽  
Motorized Spindle ◽  
Static And Dynamic Characteristics ◽  
Rotating Speed ◽  
Rotor Bearing ◽  
Bearing System

The purpose of this paper is to investigate the dynamic characteristics of a motorized spindle with externally pressurized air bearings. The externally pressurized air bearings consist of a journal bearing and a double pad thrust bearing with orifice restrictors. The equations of motion for the rotor-bearing system are established considering five degrees-of-freedom (DOF). The perturbation method and the finite difference method are introduced to calculate the static and dynamic characteristics of the air bearings; and the effects of the rotating speed and tilt angle of the rotor on the dynamic characteristics of the air bearings are analyzed. With the dynamic coefficients of the air bearings and the 5DOF rotor-dynamic model obtained, the stability, the unbalance response, and the forced response of the rotor-bearing system are investigated. Finally, the static and dynamic characteristics of the spindle are verified by an experimental study.

scholarly journals Stress Recovery Algorithm for Reduced Order Models of Mechanical Systems in Nonlinear Dynamic Operative Conditions

2021 ◽  
Author(s):  
GIUSEPPE BATTIATO ◽  
CHRISTIAN MARIA FIRRONE
Keyword(s):  
Degrees Of Freedom ◽  
Mechanical Systems ◽  
Forced Response ◽  
Response Analysis ◽  
Stress Recovery ◽  
Reduced Order Models ◽  
Technical Literature ◽  
Reduced Order ◽  
Recovery Algorithm ◽  
Safety Margins

Abstract Nonlinear forced response analyses of mechanical systems in the presence of contact interfaces are usually performed in built-in numerical codes on reduced order models (ROM). Most of the cases these derive from complex finite element (FE) models, because of the high accuracy the designers require in meshing the components in commercial FE software. In the technical literature several numerical methods are proposed for the identification of the nonlinear forced response in terms of kinematic quantity (i.e. displacement, velocity and acceleration) at the location where the master degrees-of-freedom are retained in the ROM. In fact, the displacement is the quantity usually adopted to monitor the nonlinear response, and to evaluate the effectiveness of a partially loose friction interface in damping vibrations with respect to a linear case where no friction interfaces exist and no energy dissipation can take place. However, when a ROM is used the engineering quantities directly involved in the mechanical design, i.e. the strains and stresses, cannot be retrieved without a further data processing. Moreover, in the case of a strong nonlinear behavior of the mechanical joints, the distributions of the nonlinear strains and stresses is likely different than the modal ones, meaning that the latter cannot be used to predict the safety margins of the structure working in real (nonlinear) operative conditions. This paper addresses this topic and presents a novel stress recovery algorithm for the identification of the strains and stresses resulting from a nonlinear forced response analysis on a ROM. The algorithm is applied to a bladed disk with friction contacts at the shroud joint, which make the behavior of the blades nonlinear and non-predictable by means of standard linear analyses in commercial FE software.

Sign in / Sign up

Export Citation Format

Share Document