A Three-Dimensional Tube Bundle Model Analysis for Leakage Flow Characteristics of Variable Bristle Diameter Brush Seals With Bristle Pack Stratification

2021 ◽  
Vol 143 (5) ◽  
Author(s):  
Dengqian Ma ◽  
Zhigang Li ◽  
Jun Li
Keyword(s):  
Tube Bundle ◽  
Pressure Ratio ◽  
Large Diameter ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Leakage Flow ◽  
Sealing Performance ◽  
Leakage Flow Rate ◽  
Brush Seals ◽  
Resistance Coefficients

Abstract The leakage flow characteristics of the variable bristle diameter (VBD) brush seals are numerically investigated using the three-dimensional (3D) tube bundle model with consideration of bristle pack stratification. The discretization of the computational domain applies the multiblock structured mesh, which ensures that there is no need to set interfaces between the fluid domains of the bristle pack and the cavities to eliminate interpolation errors. The bristle pack stratification is achieved by using mesh motion technique from the point of cause-effect. The effects of pressure ratio (Rp=1.5, 2.5, 3.5), axial rows of bristles (Nx=9–21), sealing clearance (c=0, 0.1 mm), bristle pack arrangements, and bristles gapping (gi=0, 0.005, 0.010, 0.015 mm) on the leakage flow characteristics and aerodynamic forces are conducted. The recorded leakage flow of the 3D tube bundle model is multiplied by circumferential loop number (Ncl) to determine total leakage flow rate of the brush seal. The numerical results agreed well with the experimental data, which verifies the reliability of the numerical method. The numerical results indicate that the leakage flow rate increases linearly with the pressure ratio. The increase of Nx has a distinctly different effect on the relative rate of leakage flow for the contacting and clearance brush seals. The use of large diameter bristles weakens the sealing performance of the brush seals, particularly in the rear region. Bristle pack stratification can improve the sealing performance of the brush seals. The large diameter bristles increase the porosity and reduce the flow resistance coefficients. On the contrary, the bristle pack stratification decreases the porosity and rises the flow resistance coefficients in the rear region. The results of this article indicate when designing VBD brush seals, the effects of bristle diameter and bristle density on the sealing performance and pressure loading capacity of the brush seals should be fully considered.

Effects of Pressure Ratio and Fin Pitch on Leakage Flow Characteristics in High Rotating Labyrinth Seals

2006 ◽  
Author(s):  
Jun Li ◽  
Xin Yan ◽  
Zhenping Feng
Keyword(s):  
Flow Rate ◽  
Geometrical Structure ◽  
Pressure Ratio ◽  
Flow Characteristics ◽  
Labyrinth Seal ◽  
Leakage Flow ◽  
Rotational Axis ◽  
Labyrinth Seals ◽  
Sealing Performance ◽  
Leakage Flow Rate

Labyrinth seals represent an important flow element in the sealing equipment of modern turbomachinery industries. The straight-through and stepped labyrinth seal are widely used in modern steam turbine due to their comparable simple structure and low manufactured costs. The influence of pressure ratio and fin pitch on the leakage flow characteristics of the straight-through and stepped labyrinth seals is numerically determined. The pressure ratio is defined as the outlet static pressure divided by the inlet total pressure. The fin pitch varied in the fixed axial distance of the labyrinth seal. The geometries investigated represent designs of the straight-through and stepped labyrinth seal typical for modern steam turbines. The leakage flow fields in the high rotating straight-through and stepped labyrinth seals are obtained by the Reynolds-Averaged Navier-Stokes solution using the commercial software FLUENT with the fixed seal clearance and fins geometrical structure. The effect of the rotational axis is also taken into account in numerical computations. Numerical simulations covered a range of pressure ratio and fin pitch for the straight-through and stepped labyrinth seals. Dimensionless discharge coefficients, describing the sealing performance, are calculated from the simulation results. The numerical results show that pressure ratio and fin pitch both affects the sealing performance with the fixed seal clearance and fin geometrical structure. The leakage flow rate decreases with the decreasing fin pitch for both the straight-through and stepped labyrinth seal at the fixed pressure ratio. Furthermore, the leakage flow rate decreases with the increasing pressure ratio at the fixed fin pitch for two kinds of labyrinth seals in the present study. This research provides technical support for improved design of labyrinth seals in turbomachinery.

Numerical Investigations on the Leakage Flow Characteristics of Brush Seal Based on the Three-Dimensional Staggered Tube Bundle Model

2021 ◽  
Vol 143 (5) ◽  
Author(s):  
Dengqian Ma ◽  
Yuanqiao Zhang ◽  
Zhigang Li ◽  
Jun Li ◽  
Xin Yan
Keyword(s):  
Flow Rate ◽  
Tube Bundle ◽  
Aerodynamic Resistance ◽  
Three Dimensional ◽  
Leakage Flow ◽  
Mesh Motion ◽  
Brush Seal ◽  
Leakage Flow Rate ◽  
Structured Mesh ◽  
Brush Seals

Abstract To accurately predict the leakage flow and resistance characteristics of brush seals, the multiblock structured mesh and the mesh motion technique are applied to the three-dimensional (3D) staggered tube bundle model of brush seals. The multiblock structured mesh can easily add nodes and set boundary layers in the interbristle gap between adjacent bristles, which can ensure good mesh quality (orthogonal angle and expansion ratio). The mesh motion technique realizes the overall axial compactness of the bristle pack. The effects of pressure ratio Rp, sealing clearance c, and bristle pack compactness on the leakage flow and resistance characteristics are investigated. To analyze the aerodynamic resistance of the brush seals, Euler number (Eu) is applied in this study. The numerical results are in good agreement with the experimental data. Thus, the accuracy of the presented numerical method is validated. For the contacting brush seal, ΔSx, i has a significant effect on the leakage flow rate reduction. For the clearance brush seal, ΔSx, i has little effect on the leakage flow rate reduction. The leakage flow passing through the sealing clearance keeps almost constant. As for aerodynamic resistance, the presence of the sealing clearance can effectively convert the pressure energy of the leakage flow into the kinetic energy. As a result, the leakage flow velocity exiting the bristle pack of the clearance brush seal is 1.5 to 2.0 times larger than that of the contacting brush seal. Although the existence of the sealing clearance obviously increases the leakage flow rate, it effectively reduces the aerodynamic forces acting on the bristles. The developed numerical approach based on the three-dimensional staggered tube bundle model and multiblock structured mesh can serve as a technical method for analysis of the sealing mechanisms of brush seals.

Numerical Investigations on the Leakage Flow Characteristics of Brush Seal Based on the 3D Staggered Tube Bundle Model

2020 ◽  
Author(s):  
Dengqian Ma ◽  
Yuanqiao Zhang ◽  
Zhigang Li ◽  
Jun Li ◽  
Xin Yan
Keyword(s):  
Flow Rate ◽  
Tube Bundle ◽  
Pressure Ratio ◽  
Aerodynamic Resistance ◽  
Flow Characteristics ◽  
Leakage Flow ◽  
Rate Reduction ◽  
Brush Seal ◽  
Leakage Flow Rate ◽  
Rotational Components

Abstract Brush seals are widely applied in turbomachinery to control leakage flow between the stationary and rotational components due to the high sealing performance. In consideration of the axial compression of the bristle pack posing a challenge to accurately predict the leakage flow rate at the practical operating condition, the 3D staggered tube bundle model is established based on the multi-block structured mesh. The mesh motion technique is used to obtain the leakage flow pattern and aerodynamic resistance performance of the brush seal. The effects of pressure ratio Rp, sealing clearance c and axial pitch reduction ΔSx,i on leakage flow characteristics as well as Eu of the brush seal were investigated. The numerical results were in good agreement with the experimental data. Thus the accuracy of the presented numerical method was validated. For the contacting brush seal, ΔSx,i has a significant effect on the leakage flow rate reduction. As the ΔSx,i increases from 0 mm to 0.004 mm, the leakage flow rate is reduced by 39.63% when Rp equals to 1.5. For the clearance brush seal, ΔSx,i has little effect on the leakage flow rate reduction. As the ΔSx,i increases from 0 mm to 0.004 mm, the leakage flow rate is reduced by 3.44% when Rp equals to 1.5 and c equals to 0.2 mm. As for the aerodynamic resistance, the presence of the sealing clearance could effectively convert the pressure energy of the leakage flow into kinetic energy. This causes that the leakage flow velocity exiting the bristle pack of the clearance brush seal is 1.5 to 2.0 times than that of the contacting brush seal. Although the existence of the sealing clearance obviously increases the leakage flow rate, it effectively reduces the aerodynamic forces acting on the bristles. This research would provide technical support for the analysis of the leakage flow characteristics of the brush seal.

Effects of Pressure Ratio and Sealing Clearance on Leakage Flow Characteristics in the Rotating Honeycomb Labyrinth Seal

2007 ◽  
Author(s):  
Jun Li ◽  
Xin Yan ◽  
Guojun Li ◽  
Zhenping Feng
Keyword(s):  
Pressure Ratio ◽  
Flow Characteristics ◽  
Labyrinth Seal ◽  
Navier Stokes ◽  
Leakage Flow ◽  
Labyrinth Seals ◽  
Aerodynamic Efficiency ◽  
Flow Losses ◽  
Leakage Flow Rate ◽  
Swirl Velocity

Honeycomb stepped labyrinth seals in turbomachinery enhance aerodynamic efficiency by reducing leakage flow losses through the clearance between rotating and stationary components. The influence of pressure ratio and sealing clearance on the leakage flow characteristics in the honeycomb stepped labyrinth seal is numerically determined. The geometries investigated represent designs of the honeycomb labyrinth seal typical for modern turbomachinery. The leakage flow fields in the honeycomb and smooth stepped labyrinth seals are obtained by the Reynolds-Averaged Navier-Stokes solution using the commercial software FLUENT. Numerical simulations covered a range of pressure ratio and three sizes of sealing clearance for the honeycomb and smooth stepped labyrinth seals. The numerical discharge coefficients of the non-rotating honeycomb and smooth stepped labyrinth seals are in good agreement with previous experimental data. In addition rotational effects are also taken into account in numerical computations. The numerical results show that the leakage flow rate increases with the increasing pressure ratio at the fixed sealing clearance for the rotating and non-rotating honeycomb labyrinth seal. The influence of the sealing clearance on the leakage flow pattern for the rotating and non-rotating honeycomb labyrinth seal are observed. Moreover, the similar leakage flow rates are obtained at the same flow condition between the rotating and non-rotating honeycomb labyrinth seal due to the honeycomb acts to kill swirl velocity development for the rotating honeycomb labyrinth seal.

Experimental and Numerical Investigations on the Leakage Flow Characteristics of the Labyrinth Brush Seal

2012 ◽  
Vol 134 (10) ◽  
Author(s):  
Jun Li ◽  
Bo Qiu ◽  
Zhenping Feng
Keyword(s):  
Experimental Data ◽  
Pressure Ratio ◽  
Flow Characteristics ◽  
Leakage Rate ◽  
Navier Stokes ◽  
Leakage Flow ◽  
Blow Down ◽  
Pressure Distributions ◽  
Brush Seal ◽  
Brush Seals

The leakage rate of the labyrinth brush seal was experimentally measured and numerically investigated in this paper. Four different rotational speeds of 0, 1500, 2400 and 3000 rpm were utilized to investigate the effects on the leakage rate of the labyrinth brush seal. In addition, five different pressure ratios and two initial clearances were also adopted to study the influences of pressure ratio and clearance size on the leakage rate of the labyrinth brush seal. The leakage rates of the experimental labyrinth brush seal at different rotational speeds, pressure ratios, and initial clearances were also predicted using Reynolds-averaged Navier-Stokes (RANS) solutions coupling with a non-Darcian porous medium model. The rotor centrifugal growth and bristle blow-down effects were considered in the present numerical research. The rotor centrifugal growth at different rotational speeds was calculated using the finite element method (FEM). The variation of the sealing clearance size with rotor centrifugal growth and bristle blow-down was analyzed. The numerical leakage rate was in good agreement with the experimental data. The effects of rotational speeds, pressure ratios, and clearance sizes on the leakage flow characteristics of brush seals were also investigated based on the experimental data and numerical results. The detailed leakage flow fields and pressure distributions of the brush seals were also presented.

Numerical Investigations on the Leakage Flow Characteristics of Pocket Damper Seals

2011 ◽  
Author(s):  
Zhigang Li ◽  
Jun Li ◽  
Zhenping Feng ◽  
Jiandao Yang ◽  
Rui Yang ◽  
...  
Keyword(s):  
Flow Rate ◽  
Rotational Speed ◽  
Pressure Ratio ◽  
Flow Characteristics ◽  
Labyrinth Seal ◽  
Leakage Rate ◽  
Numerical Results ◽  
Flow Coefficient ◽  
Leakage Flow ◽  
Leakage Flow Rate

The effects of pressure ratios, rotational speeds and sealing clearances on the leakage flow characteristics of pocket damper seals (PDS) were numerically investigated using Reynolds-Averaged Navier-Stokes (RANS) solutions. The leakage flow rate of the experimental PDS with the eight-bladed and eight-pocket was conducted at three different pressure drops and three different rotational speeds. The numerical results were in agreement with the experimental data. Six pressure ratios, four rotational speeds and four sealing clearances were utilized to study the effects of theses factors on the leakage flow characteristics of the PDS. Numerical results show that the leakage rate of the PDS increases with decreased pressure ratio. The leakage rate decreases with the increasing rotational speed, and this phenomenon is more pronounced at higher rotational speed. At the highest rotational speed 20200rpm, the flow coefficient is up to 4.4% less than that of the non-rotating case. The leakage rate increases linearly with sealing clearance increasing. The comparison of the leakage flow rate shows that the PDS leaks slightly less than that of the labyrinth seal at the same pressure ratio, rotational speed and sealing clearance, especially at the higher rotational speed case. Furthermore, the circumferential partition wall can significantly decrease the circumferential flow in the PDS cavity. At the highest rotational speed with 20200rpm, the swirl ratio in the active and inactive cavity of the PDS is reduced by 94.5% and 46% compared to the labyrinth seal, respectively.

Numerical Investigations on Leakage Performance of the Rotating Labyrinth Honeycomb Seal

2010 ◽  
Vol 132 (6) ◽  
Author(s):  
Jun Li ◽  
Shengru Kong ◽  
Xin Yan ◽  
Shinnosuke Obi ◽  
Zhengping Feng
Keyword(s):  
Flow Rate ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Navier Stokes ◽  
Cell Diameter ◽  
Leakage Flow ◽  
Steam Turbines ◽  
Honeycomb Seal ◽  
Leakage Flow Rate ◽  
Honeycomb Cell

Three-dimensional Reynolds-averaged Navier–Stokes (RANS) solutions from CFX were utilized to investigate the leakage flow characteristics in the labyrinth honeycomb seal of steam turbines. At first, the accuracy and reliability of the utilized RANS approach was demonstrated using the published experimental data of the honeycomb seal. It showed that the utilized numerical method has sufficient precision to predict the leakage performance in seals. Then a range of sealing clearances, cell diameters, cell depths, rotation speeds, and pressure ratios were investigated to determine how these factors affect the leakage flow rate of the labyrinth honeycomb seal. The computed leakage flow rate increased with increasing sealing clearance and pressure ratios. Furthermore, the results show that the studied labyrinth honeycomb seal has the optimum sealing performance in the case of honeycomb cell diameter equals labyrinth step width, and the ratio of the honeycomb cell depth to honeycomb cell diameter is 0.93 under the designed condition. The flow pattern of each case is also illustrated to describe the leakage flow characteristics in labyrinth honeycomb seals.

Experimental and Numerical Investigations on the Leakage Flow Characteristics of the Labyrinth Brush Seal

2012 ◽  
Author(s):  
Jun Li ◽  
Bo Qiu ◽  
Shengke Jiang ◽  
Xianglin Kong ◽  
Zhenping Feng
Keyword(s):  
Experimental Data ◽  
Pressure Ratio ◽  
Flow Characteristics ◽  
Leakage Rate ◽  
Navier Stokes ◽  
Leakage Flow ◽  
Blow Down ◽  
Pressure Distributions ◽  
Brush Seal ◽  
Brush Seals

The leakage rate of the labyrinth brush seal was experimentally measured and numerically investigated in this paper. Four different rotational speeds with 0, 1500, 2400 and 3000 rpm were utilized to investigate the effects on the leakage rate of the labyrinth brush seal. In addition, five different pressure ratios and two initial clearances were also adopted to study the influences of pressure ratio and clearance size on the leakage rate of the labyrinth brush seal. The leakage rate of experimental labyrinth brush seal at different rotational speeds, pressure ratios and initial clearances were also predicted using Reynolds-Averaged Navier-Stokes (RANS) solution coupling with non-Darcian porous medium model. The rotor centrifugal growth and bristle blow-down effects were considered in the present numerical research. The rotor centrifugal growth at different rotational speeds was calculated using Finite Element Method (FEM). The variation of sealing clearance size with rotor centrifugal growth and bristle blow-down was analyzed. The numerical leakage rate was in good agreement with the experimental data. The effects of rotational speeds, pressure ratios and clearance sizes on the leakage flow characteristics of brush seals were also investigated based on the experimental data and numerical results. The detailed leakage flow fields and pressure distributions of brush seals were also presented.

scholarly journals Leakage Characteristic Identification of Labyrinth Seals on Reciprocating Piston through Transient Simulations

2019 ◽  
Vol 2019 ◽  
pp. 1-12
Author(s):  
Lingzi Wang ◽  
Jianmei Feng ◽  
Mingfeng Wang ◽  
Zenghui Ma ◽  
Xueyuan Peng
Keyword(s):  
Flow Rate ◽  
Pressure Ratio ◽  
Piston Compressor ◽  
Pressure Change ◽  
Labyrinth Seal ◽  
Relative Molecular Mass ◽  
Geometrical Parameters ◽  
Leakage Flow ◽  
Reciprocating Motion ◽  
Leakage Flow Rate

In the reciprocating labyrinth piston compressor, the characteristic of the internal leakage is crucial for the leakage management and performance improvement of the compressor. However, most of the published studies investigated the rotor-stator system, and those who study the reciprocating piston-cylinder system basically focus on the effects of the geometrical parameters. These conclusions could not directly be applied to predict the real-time leakage flow rate through the labyrinth seal because of the fast reciprocating motion of the piston, which will cause continually pressure change in two compression chambers, and then the pressure fluctuation will affect the flow through the labyrinth seal. A transient simulation model employing the multiscale dynamic mesh, which considers the effect of the reciprocating motion of the piston in the cylinder, is established to identify the characteristics of the internal leakage. This model was verified by a specially designed compressor, and the influence of various parameters was analyzed in detail. The sealing performance decreased linearly with the increase in the pressure ratio, and higher pressure inlet leads to higher leakage flow under the same pressure ratio. The labyrinth seal performance positively correlated to the increase of the rotational speed. Leakage characteristics of five working mediums were carried out, and the results indicated that the relative leakage decreased with an increase in the relative molecular mass. From this study, the realistic internal leakage flow rate under different operating parameters in the reciprocating labyrinth piston compressor could be predicated.

The Interaction of Turbine Inter-Platform Leakage Flow With the Mainstream Flow

2005 ◽  
Author(s):  
Kevin Reid ◽  
John Denton ◽  
Graham Pullan ◽  
Eric Curtis ◽  
John Longley
Keyword(s):  
Three Dimensional ◽  
Leakage Flow ◽  
Turbine Performance ◽  
Leakage Flow Rate ◽  
Single Piece ◽  
Flow Through ◽  
Aero Engines ◽  
Nozzle Guide ◽  
Nozzle Guide Vanes ◽  
Leakage Fraction

Individual nozzle guide vanes (NGVs) in modern aero engines are often cast as a single piece with integral hub and casing endwalls. When in operation there is a leakage flow through the chord-wise inter-platform gaps. An investigation into the effect of this leakage flow on turbine performance is presented. Efficiency measurements and NGV exit area traverse data from a low speed research turbine are reported. Tests show that this leakage flow can have a significant impact on turbine performance, but that below a threshold leakage fraction this penalty does not rise with increasing leakage flow rate. The effect of various seal clearances are also investigated. Results from steady-state simulations using a three-dimensional multiblock RANS solver are presented with particular emphasis paid to the physics of the mainstream/leakage interaction and the loss generation.

Sign in / Sign up

Export Citation Format

Share Document