Numerical Investigations on Leakage Performance of the Rotating Labyrinth Honeycomb Seal

2010 ◽  
Vol 132 (6) ◽  
Author(s):  
Jun Li ◽  
Shengru Kong ◽  
Xin Yan ◽  
Shinnosuke Obi ◽  
Zhengping Feng
Keyword(s):  
Flow Rate ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Navier Stokes ◽  
Cell Diameter ◽  
Leakage Flow ◽  
Steam Turbines ◽  
Honeycomb Seal ◽  
Leakage Flow Rate ◽  
Honeycomb Cell

Three-dimensional Reynolds-averaged Navier–Stokes (RANS) solutions from CFX were utilized to investigate the leakage flow characteristics in the labyrinth honeycomb seal of steam turbines. At first, the accuracy and reliability of the utilized RANS approach was demonstrated using the published experimental data of the honeycomb seal. It showed that the utilized numerical method has sufficient precision to predict the leakage performance in seals. Then a range of sealing clearances, cell diameters, cell depths, rotation speeds, and pressure ratios were investigated to determine how these factors affect the leakage flow rate of the labyrinth honeycomb seal. The computed leakage flow rate increased with increasing sealing clearance and pressure ratios. Furthermore, the results show that the studied labyrinth honeycomb seal has the optimum sealing performance in the case of honeycomb cell diameter equals labyrinth step width, and the ratio of the honeycomb cell depth to honeycomb cell diameter is 0.93 under the designed condition. The flow pattern of each case is also illustrated to describe the leakage flow characteristics in labyrinth honeycomb seals.

Experimental and Numerical Investigations on the Aerodynamic Performance of the Three-Stage Turbine With Consideration of the Leakage Flow Effect

2016 ◽  
Author(s):  
Yang Chen ◽  
Jun Li ◽  
Chaoyang Tian ◽  
Gangyun Zhong ◽  
Xiaoping Fan ◽  
...  
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Rotor Blade ◽  
Three Dimensional ◽  
Aerodynamic Performance ◽  
Navier Stokes ◽  
Leakage Flow ◽  
Leakage Flows ◽  
Wheel Disk

The aerodynamic performance of three-stage turbine with different types of leakage flows was experimentally and numerically studied in this paper. The leakage flows of three-stage turbine included the shroud seal leakage flow between the rotor blade tip and case, the diaphragm seal leakage flow between the stator blade diaphragm and shaft, as well as the shaft packing leakage flow and the gap leakage flow between the rotor blade curved fir-tree root and wheel disk. The total aerodynamic performance of three-stage turbine including leakage flows was firstly experimentally measured. The detailed flow field and aerodynamic performance were also numerically investigated using three-dimensional Reynolds-Averaged Navier-Stokes (RANS) and S-A turbulence model. The numerical mass flow rate and efficiency showed well agreement with experimental data. The effects of leakage flows between the fir-tree root and the wheel disk were studied. All leakage mass flow fractions, including the mass flow rate in each hole for all sets of root gaps were given for comparison. The effect of leakage flow on the aerodynamic performance of three-stage was illustrated and discussed.

Effects of Inlet Preswirl and Cell Diameter and Depth on Honeycomb Seal Characteristics

2010 ◽  
Vol 132 (12) ◽  
Author(s):  
Xin Yan ◽  
Jun Li ◽  
Zhenping Feng
Keyword(s):  
Temperature Increase ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Labyrinth Seal ◽  
Leakage Rate ◽  
Navier Stokes ◽  
Cell Diameter ◽  
Total Temperature ◽  
Honeycomb Seals ◽  
Honeycomb Cell

Three-dimensional Reynolds-averaged Navier–Stokes solutions are employed to investigate the discharge and total temperature increase characteristics of the stepped labyrinth seal with honeycomb land. First, the relations between the windage heating number and the circumferential Mach number at different Reynolds numbers for different honeycomb seals are calculated and compared with the experimental data. The obtained numerical results show that the present three-dimensional periodic model can properly predict the total temperature increase in honeycomb seals. Then, a range of pressure ratios, three inlet preswirl ratios, four sizes of honeycomb cell diameter, and nine sizes of cell depth are selected to investigate the influence of inlet preswirl ratios and honeycomb geometry sizes on the discharge and total temperature increase characteristics of the stepped labyrinth seal. It shows that the leakage rate increases with the increase in cell diameter, and the cell depth has a strong influence on the discharge behavior. However, the influence of the inlet preswirl on the leakage rate is found to be little in the present study. For the total temperature increase characteristic, the inlet preswirl ratio and pressure ratio have more pronounced influence than those of cell depth and diameter. Furthermore, the relations between the leakage rate and cell depth and diameter, as well as the relations between the windage heating power and cell depth and diameter, are not monotonic functions if the pressure ratio is kept constant.

Estimating HP-IP Mid-Span Packing Leakage in Combined Cycles

2006 ◽  
Author(s):  
Tsatsu Fiadjoe
Keyword(s):  
Flow Rate ◽  
Combined Cycle ◽  
Variation Method ◽  
Leakage Flow ◽  
Steam Turbines ◽  
Multiple Test ◽  
External Cooling ◽  
Temperature Method ◽  
Leakage Flow Rate ◽  
Combined Cycles

When a turbine has combined High Pressure (HP) and Intermediate Pressure (IP) sections, there is a steam flow path between the sections. In Combined Cycle steam turbines this internal leakage flow rate needs to be determined for the steam turbine performance calculations. However, since the leakage is internal to the turbine, it cannot be measured directly. One method which has been employed in determining the Mid-packing leakage flow rate is the Variation of Initial and/or Reheat Temperature method. This method is described in the paper “Estimating The Leakage From HP To IP Turbine Sections” presented by J.A. Booth and D.E. Kautzmann. It involves using the convergence of IP efficiency plots from multiple test runs to estimate the HP-IP leakage flow rate. Although this method has been employed successfully in large steam applications, it has generally not produced consistent results for Combined Cycle steam turbines. The lack of convergence for Combined Cycles may be due to the fact that some of the assumptions made in applying the method to large steam applications are not valid for Combined Cycle applications. Some of the assumptions which need to be reviewed and modified for Combined Cycle application are as follows: • Constant IP efficiency for all test runs; • Constant throttle flow during all test runs; • Constant section pressure ratios for all test runs; • No influence of external cooling or admission flows. This paper reviews the modifications to the traditional Initial and/or Reheat temperature variation method to make the Mid-Packing leakage calculations more consistent for Combined Cycle applications. Some data has shown that incorporating these additional changes improves the convergence of Mid-packing leakage determination.

Numerical Investigations of the Flow Characteristics in the Straight-Through Honeycomb Seal

2005 ◽  
Author(s):  
Jun Li ◽  
Qinghua Deng ◽  
Zhenping Feng
Keyword(s):  
Pressure Difference ◽  
Three Dimensional ◽  
Engineering Application ◽  
Flow Characteristics ◽  
Simulation Method ◽  
Labyrinth Seal ◽  
Honeycomb Structure ◽  
Computational Grids ◽  
Steam Turbines ◽  
Honeycomb Seal

Investigation of the flow characteristics in the straight-through honeycomb seal installed in the diagram for steam turbines using the numerical simulation method is presented in this paper. To illustrate the leakage flow performance of the straight-through honeycomb seal, the straight-through labyrinth seal with the same sealing clearance and pressure difference is also calculated. The flow fields are predicted using a commercial finite volume code with the standard k-ε turbulence model. The computational grids include the basic sealing geometries as well as the three-dimensional honeycomb seal and labyrinth seal structures. The obtained results demonstrate that the dimensionless discharge coefficient of the honeycomb seal is smaller than that of the labyrinth seal at the same sealing clearance and pressure difference. The leakage flows of the honeycomb seal are divided into much more smaller recirculation flows than that of the labyrinth seal due to its honeycomb structures. The honeycomb structure of the honeycomb seal leads to decrease the leakage mass flow rate. The flow characteristics of the honeycomb seal and labyrinth seal are also illustrated. This study can be able to supply the theoretical foundation and technical support for the engineering application of the honeycomb seal in steam turbines.

Study of Losses in a Leakage Flow Through the Passage of Shrouded Turbine Blades With Swirl Velocity

2001 ◽  
Author(s):  
Yumin Xiao ◽  
R. S. Amano
Keyword(s):  
Turbine Blades ◽  
Three Dimensional ◽  
Major Effect ◽  
Tip Clearance ◽  
Navier Stokes ◽  
Leakage Flow ◽  
Complex Flow ◽  
Local Pressure ◽  
Leakage Flow Rate ◽  
Calculation Results

In this paper the study of the flows over shrouded turbine blades with staggered-seals is presented by computing the three-dimensional Reynolds-Averaged Navier-Stokes (RANS) equations along with a compressible non-linear k-ε turbulence model. The swirl of the blade is coupled into the calculation. A multi-zone technique is used to generate the grids in the complex flow channel. The calculation results show that the leakage flow rate in the seal-channel is dominated by the pressure difference. It was also observed that the circumferential momentum transfer in the channel is very slow in the region in front of the seal tooth. The major effect of the rotating blade is the increase of local pressure distribution along the shrouded tip clearance path. However, the swirl motion of the blade tip does not significantly change the flow pattern in the axial-radial plane.

A Three-Dimensional Tube Bundle Model Analysis for Leakage Flow Characteristics of Variable Bristle Diameter Brush Seals With Bristle Pack Stratification

2021 ◽  
Vol 143 (5) ◽  
Author(s):  
Dengqian Ma ◽  
Zhigang Li ◽  
Jun Li
Keyword(s):  
Tube Bundle ◽  
Pressure Ratio ◽  
Large Diameter ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Leakage Flow ◽  
Sealing Performance ◽  
Leakage Flow Rate ◽  
Brush Seals ◽  
Resistance Coefficients

Abstract The leakage flow characteristics of the variable bristle diameter (VBD) brush seals are numerically investigated using the three-dimensional (3D) tube bundle model with consideration of bristle pack stratification. The discretization of the computational domain applies the multiblock structured mesh, which ensures that there is no need to set interfaces between the fluid domains of the bristle pack and the cavities to eliminate interpolation errors. The bristle pack stratification is achieved by using mesh motion technique from the point of cause-effect. The effects of pressure ratio (Rp=1.5, 2.5, 3.5), axial rows of bristles (Nx=9–21), sealing clearance (c=0, 0.1 mm), bristle pack arrangements, and bristles gapping (gi=0, 0.005, 0.010, 0.015 mm) on the leakage flow characteristics and aerodynamic forces are conducted. The recorded leakage flow of the 3D tube bundle model is multiplied by circumferential loop number (Ncl) to determine total leakage flow rate of the brush seal. The numerical results agreed well with the experimental data, which verifies the reliability of the numerical method. The numerical results indicate that the leakage flow rate increases linearly with the pressure ratio. The increase of Nx has a distinctly different effect on the relative rate of leakage flow for the contacting and clearance brush seals. The use of large diameter bristles weakens the sealing performance of the brush seals, particularly in the rear region. Bristle pack stratification can improve the sealing performance of the brush seals. The large diameter bristles increase the porosity and reduce the flow resistance coefficients. On the contrary, the bristle pack stratification decreases the porosity and rises the flow resistance coefficients in the rear region. The results of this article indicate when designing VBD brush seals, the effects of bristle diameter and bristle density on the sealing performance and pressure loading capacity of the brush seals should be fully considered.

scholarly journals Optimizing the Geometric Parameters of a Straight-Through Labyrinth Seal to Minimize the Leakage Flow Rate and the Discharge Coefficient

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 705
Author(s):  
Seung Il Baek ◽  
Joon Ahn
Keyword(s):  
Flow Rate ◽  
Axial Length ◽  
Discharge Coefficient ◽  
Labyrinth Seal ◽  
Geometric Parameters ◽  
Navier Stokes ◽  
Leakage Flow ◽  
Leakage Flow Rate ◽  
Tooth Width ◽  
Cavity Width

A straight-through labyrinth seal is one of the most popular non-contacting annular seals through which energy dissipation by turbulence viscosity interaction is achieved with a series of teeth and cavities. The geometric parameters of the straight-through labyrinth seal, such as clearance, tooth width, tooth height, cavity width, and tooth inclination angle, affect its performance. The space for installing a labyrinth seal in turbomachinery is limited, and so it is important to optimize its geometry for a fixed axial length in order to minimize the leakage flow rate and the discharge coefficient. The objective of the current study is to understand the effects of changing the geometric parameters of the seal on the leakage flow rate and the discharge coefficient, and to determine the optimized geometry for a fixed axial length. When the whole axial length is fixed, the most effective way to decrease the discharge coefficient is to reduce the cavity width by increasing the number of cavities. However, if the number of cavities is too high, the beneficial effect of more cavities can be reversed. The results of this study will help turbomachinery manufacturers to design a more efficient labyrinth seal. Numerical simulations of leakage flow for the straight-through labyrinth seal were carried out using Reynolds-Averaged Navier–Stokes (RANS) models, and the results for their discharge coefficients and pressure distributions were compared to previously published experimental data.

Effects of Pressure Ratio and Sealing Clearance on Leakage Flow Characteristics in the Rotating Honeycomb Labyrinth Seal

2007 ◽  
Author(s):  
Jun Li ◽  
Xin Yan ◽  
Guojun Li ◽  
Zhenping Feng
Keyword(s):  
Pressure Ratio ◽  
Flow Characteristics ◽  
Labyrinth Seal ◽  
Navier Stokes ◽  
Leakage Flow ◽  
Labyrinth Seals ◽  
Aerodynamic Efficiency ◽  
Flow Losses ◽  
Leakage Flow Rate ◽  
Swirl Velocity

Honeycomb stepped labyrinth seals in turbomachinery enhance aerodynamic efficiency by reducing leakage flow losses through the clearance between rotating and stationary components. The influence of pressure ratio and sealing clearance on the leakage flow characteristics in the honeycomb stepped labyrinth seal is numerically determined. The geometries investigated represent designs of the honeycomb labyrinth seal typical for modern turbomachinery. The leakage flow fields in the honeycomb and smooth stepped labyrinth seals are obtained by the Reynolds-Averaged Navier-Stokes solution using the commercial software FLUENT. Numerical simulations covered a range of pressure ratio and three sizes of sealing clearance for the honeycomb and smooth stepped labyrinth seals. The numerical discharge coefficients of the non-rotating honeycomb and smooth stepped labyrinth seals are in good agreement with previous experimental data. In addition rotational effects are also taken into account in numerical computations. The numerical results show that the leakage flow rate increases with the increasing pressure ratio at the fixed sealing clearance for the rotating and non-rotating honeycomb labyrinth seal. The influence of the sealing clearance on the leakage flow pattern for the rotating and non-rotating honeycomb labyrinth seal are observed. Moreover, the similar leakage flow rates are obtained at the same flow condition between the rotating and non-rotating honeycomb labyrinth seal due to the honeycomb acts to kill swirl velocity development for the rotating honeycomb labyrinth seal.

Numerical Study of the Effect of Honeycomb Tip on Tip Leakage Flow in Turbine Cascade

2016 ◽  
Author(s):  
Yunfeng Fu ◽  
Fu Chen ◽  
Cong Chen ◽  
Yanping Song
Keyword(s):  
Flow Rate ◽  
Numerical Study ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Turbine Cascade ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Honeycomb Seal ◽  
Leakage Flow Rate ◽  
Highly Loaded

A novel leakage flow control strategy with honeycomb seal applied on the tip of the rotor blades in a highly-loaded turbine cascade is proposed. The numerical method is used to study the tip leakage flow in a highly-loaded turbine cascades with flat tip and with honeycomb seal structure, the mechanism of honeycomb tip on inhibiting leakage flow is analyzed, the influence of various relative gap heights is also been investigated. The discussions of the action of the honeycomb-tip structure in reducing leakage flow and improving the turbine efficiency provide the according for control methods of tip leakage flow. Through the comparative study among three different tip structures of honeycomb tip, honeycomb casing and flat tip, the results show that both honeycomb tip and honeycomb casing inhibit the leakage flow effectively, but honeycomb tip has positive effect on reducing the flow loss in cascade. For the cascade with honeycomb tip, on one hand, the vortices rolled up in the regular hexagon honeycomb cavities dissipate the energy of the tip leakage flow, and the range of influence of the vortices is nearly one third of the tip clearance height. On the other hand, the radial jets caused by the honeycomb obstruct the tip leakage flow like a “pneumatic fence”, resulting in weaker leakage flow and less leakage flow rate. Besides, the honeycomb tip reduces the scale of the leakage vortex, thus the leakage loss also decreases. Compared with the flat tip cascade at the clearance height of 1%H, the honeycomb tip cascade with the same clearance height obtains decrease of the leakage flow rate and leakage flow speed in circumference by 10.16% and 20%. As a result, the leakage vortex in honeycomb tip cascade is undermined, the loss is reduced by nearly 4.43%. Considering the abradable property of the honeycomb seal that can protect the blade tips from damage, the cascade with honeycomb tip structure can obtain a smaller clearance height and achieve better sealing effect. Compared to cascade with the flat tip at the clearance height of 2%H, the amount of leakage flow using inlet flow in the honeycomb tip cascades decreases by 17.33%, 36.63% and 54.79% at the clearance heights of 2%H, 1.5%H and 1%H, the losses related to the leakage flow is reduced by nearly 5.71%, 14.33% and 25.24%, respectively.

Direct Constrained Computational Fluid Dynamics Based Optimization of Three-Dimensional Blading for the Exit Stage of a Large Power Steam Turbine

2002 ◽  
Vol 125 (1) ◽  
pp. 385-390 ◽  
Author(s):  
P. Lampart ◽  
S. Yershov
Keyword(s):  
Steam Turbine ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Steam Turbines ◽  
Original Design ◽  
Large Power ◽  
Wide Range

The paper describes results of direct constrained optimization using Nelder-Mead’s method of deformed polyhedron and a Reynolds-averaged Navier-Stokes (RANS) solver to optimize the shape of three-dimensional blading for the exit stage of a large power steam turbine. The computations of the flowfield in the stator and rotor are compressible, viscous, and three-dimensional. Turbulence effects are taken into account using the modified model of Baldwin-Lomax. The objective function is the stage efficiency, with the exit energy considered a loss, and with constraints imposed on the mass flow rate in the form of a penalty function if the mass flow rate falls beyond the required range. The blade sections (profiles) are assumed not to change during the optimization. Two optimization tasks are reported in this paper, first—optimizing the stator straight and compound circumferential lean, and also stator and rotor stagger angles to keep the flow rate unchanged, giving a total number of optimized parameters equal to 5; second—optimizing the stator straight and compound axial sweep, also with stator and rotor stagger angles, also giving five optimized parameters. The process of optimization is carried out for a nominal load; however, due to the fact that exit stages of steam turbines operate over a wide range of flow rates away from the nominal conditions, the original and final geometries are also checked for low and high loads. The process of optimization gives new designs with new three-dimensional stacking lines of stator blades, and with significantly increased efficiencies, compared to the original design, at least for a larger part of the assumed range of load.

Sign in / Sign up

Export Citation Format

Share Document