Very Large Eddy Simulation of Aero-Thermal Performance in Squealer Tip Gap

2021 ◽  
pp. 1-49
Author(s):  
Xin Yan
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Thermal Performance ◽  
Pressure Loss ◽  
Total Pressure ◽  
Total Pressure Loss ◽  
Vortex System ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Cavity Floor

Abstract To improve the resolution accuracy and get deep insight into the flow structures in squealer tip gap, the Very Large Eddy Simulation (VLES) method was implemented into the commercial CFD (Computational Fluid Dynamics) solver with the User Defined Function (UDF). Based on the published experimental data, the numerical accuracy of VLES method was validated. With VLES method, the unsteady heat transfer coefficient distributions on the squealer tip and total pressure loss in the blade passage were computed. The influences of coherent vortex structures on aero-thermal performance in the squealer tip gap were analyzed. The results show that the Brown-Roshko vortices are the main driver for the formation of cavity vortex system. The direct impingement of pass-over leakage into the cavity is the main cause of high heat transfer area on the cavity floor near leading edge. The unsteady fluctuations of leakage rate through the tip gap reach about ±8% of the time-averaged value. The development of leakage vortex accounts for the major contribution of total pressure loss in the squealer tipped blade. Due to flow unsteadiness, the fluctuation of pitch-averaged total pressure loss coefficient induced by leakage vortex system reaches about ±30% of the time-averaged value. The unsteady fluctuation of pitch-averaged heat transfer coefficient on the cavity floor reaches about ±35% of the time-averaged value, while on the shroud surface it is only fluctuated by about ±10%.

Investigations of Heat Transfer and Film Cooling Effect on a Worn Squealer Tip

2020 ◽  
Author(s):  
Mingliang Ye ◽  
Xin Yan
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Pressure Loss ◽  
Total Pressure ◽  
Total Pressure Loss ◽  
Wear Depth ◽  
Original Design ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cavity Floor

Abstract Wear damage commonly occurs in modern gas turbine rotor blade tip due to relative movements and expansions between rotating and stationary parts. Tip wear has a significant impact on the aerodynamic, heat transfer and cooling performance of rotor blades, thus threatening the economy and safety of whole gas turbine system. Based on a simple linear wear model, this paper numerically investigates the aerodynamic, heat transfer and film cooling performance of a worn squealer tip with three starting-locations of wear (sl = 25%Cax, 50%Cax and 75%Cax) and five wear-depths (wd = 0.82%, 1.64%, 2.46%, 3.28% and 4.10%). Firstly, based on the existing experimental data, numerical methods and grid independence are examined carefully. Then, three dimensional flow fields, total pressure loss distributions, heat transfer coefficients and film cooling effectiveness in worn squealer tip region are computed, which are compared with the original design case. The results show that, with the increase of wear depth and the movement of wear starting-location to the leading edge, the scale and intensity of cavity vortex are increased, which results in the extended high heat transfer area on cavity floor near the leading edge. Wear makes more coolant flow out of the cavity, and reduces the area-averaged film cooling effectiveness at the bottom of cavity, but increases the film cooling effectiveness on pressure-side rim. The increase of wear depth makes more flow leak through the tip gap, thus increasing the scale and intensity of leakage vortex and further increasing the total pressure loss in the tip gap. Compared with the original design case, as the wear depth is increased from 0.82% to 4.10%, the mass-averaged total pressure loss in cascade is increased by 0.3–6.7%, the area-averaged heat transfer coefficient on cavity floor is increased by 1.7–29.1% while on squealer rim it is decreased by 3.1–26.3%, and the area-averaged film cooling effectiveness on cavity floor is decreased by 0.035 at most while on squealer rim it is increased by 0.064 at most.

Measurement of Blade Tip Heat Transfer and Leakage Flow in a Turbine Cascade With a Multi-Cavity Squealer Tip

2013 ◽  
Author(s):  
Jung Shin Park ◽  
Sang Hoon Lee ◽  
Jae Su Kwak ◽  
Won Suk Lee ◽  
Jin Taek Chung
Keyword(s):  
Heat Transfer ◽  
Pressure Loss ◽  
Total Pressure ◽  
Leading Edge ◽  
Total Pressure Loss ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Measurement Results ◽  
Blade Tip ◽  
Cavity Floor

Tip leakage flow induces high heat transfer to the blade tip and causes significant aerodynamic losses. In this paper, we propose a multi-cavity squealer tip with an additional rib in the squealer cavity. Our study investigated the effects of the rib location and shape on the blade tip heat transfer and the total pressure loss. Experiments were performed in a five-bladed linear cascade using a low speed wind tunnel. The blade chord, pitch, and span length were 126mm, 102.7mm, and 160mm, respectively. The Reynolds number, based on the blade chord and cascade exit velocity, was 2.44×105, and a tip clearance of 1.25% of the blade span was considered. The additional rib was installed in the squealer tip cavity near the leading edge, the mid-chord, and the training edge, respectively. The shape of the rib was also varied from rectangular to triangular in order to minimize the rib surface area exposed to the hot gas. The secondary flow and total pressure loss were measured using a seven-hole probe at one-chord downstream of the blade trailing edge, and the heat transfer coefficient distributions were measured by utilizing the hue-detection based transient liquid crystal technique. Flow measurement results indicated that the proposed multi-cavity tip reduced the total pressure loss. The blade tip heat transfer measurement results showed that the proposed multi-cavity tip was able to reduce the maximum heat transfer region near the cavity floor near the leading edge, but the heat transfer on the second cavity floor increased due to the leakage flow reattachment.

Conjugate Heat Transfer Characteristics of Double Wall Cooling With Gradient Diameter of Film and Impingement Holes

2021 ◽  
Author(s):  
Juan He ◽  
Qinghua Deng ◽  
Zhenping Feng
Keyword(s):  
Heat Transfer ◽  
Pressure Loss ◽  
Total Pressure ◽  
Flow Direction ◽  
Turbine Blades ◽  
Total Pressure Loss ◽  
Advanced Technique ◽  
Cooling Effectiveness ◽  
Uniform Pattern ◽  
Double Wall

Abstract Double wall cooling, consisting of internal impingement cooling and external film cooling, is believed to be the most advanced technique in modern turbine blades cooling. In this paper, to improve the uniformity of temperature distribution, a flat plate double wall cooling model with gradient diameter of film and impingement holes was proposed, and the heat transfer and flow characteristics were investigated by solving steady three-dimensional Reynolds-Averaged Navier-Stokes (RANS) equations with SST k-ω turbulence model. The influence of gradient diameter on overall cooling effectiveness and total pressure loss was studied by comparing with the uniform pattern at the blowing ratios ranging from 0.5 to 2. For gradient diameter of film hole patterns, results show that −10% film pattern always has the lowest film flow non-uniformity coefficient. The laterally averaged overall cooling effectiveness of uniform pattern lies between that of +10% and −10% film patterns, but the intersection of three patterns moves upstream from the middle of flow direction with the increase of blowing ratio. Therefore, the −10% film pattern exerts the highest area averaged cooling effectiveness, which is improved by up to 1.6% and 1% at BR = 0.5 and 1 respectively compared with a uniform pattern. However, at higher blowing ratios, the +10% film pattern maintains higher cooling effectiveness and lower total pressure loss. For gradient diameter of impingement hole patterns, the intersection of laterally averaged overall cooling effectiveness in three patterns is located near the middle of flow direction under all blowing ratios. The uniform pattern has the highest area averaged cooling effectiveness and the smallest non-uniform coefficient, but the −10% jet pattern has advantages of reducing pressure loss, especially in the laminated loss.

Second Vane Total Pressure Loss Due to Endwall Iceform Contouring

2008 ◽  
Author(s):  
Ronald S. LaFleur
Keyword(s):  
Heat Transfer ◽  
Secondary Flow ◽  
Pressure Loss ◽  
Total Pressure ◽  
Aerodynamic Drag ◽  
Pressure Coefficient ◽  
Secondary Flows ◽  
Total Pressure Loss ◽  
Surface Shape ◽  
Exit Plane

The iceformation design method generates an endwall contour, altering the secondary flows that produce elevated endwall heat transfer load and total pressure losses. Iceformation is an analog to regions of metal melting where a hot fluid alters the isothermal surface shape of a part as it is maintained by a cooling fluid. The passage flow, heat transfer and geometry evolve together under the constraints of flow and thermal boundary conditions. The iceformation concept is not media dependent and can be used in analogous flows and materials to evolve novel boundary shapes. In the past, this method has been shown to reduce aerodynamic drag and total pressure loss in flows such as diffusers and cylinder/endwall junctures. A prior paper [1] showed that the Reynolds number matched iceform geometry had a 24% lower average endwall heat transfer than the rotationally symmetric endwall geometry of the Energy Efficiency Engine (E3). Comparisons were made between three endwall geometries: the ‘iceform’, the ‘E3’ and the ‘flat’ as a limiting case of the endwall design space. This paper adds to the iceformation design record by reporting the endwall aerodynamic performances. Second vane exit flow velocities and pressures were measured using an automated 2-D traverse of a 1.2 mm diameter five-hole probe. Exit plane maps for the three endwall geometries are presented showing the details of the total pressure coefficient contours and the velocity vectors. The formation of secondary flow vortices is shown in the exit plane and this results in an impact on exit plane total pressure loss distribution, off-design over- and under-turning of the exit flow. The exit plane contours are integrated to form overall measures of the total pressure loss. Relative to the E3 endwall, the iceform endwall has a slightly higher total pressure loss attributed to higher dissipation of the secondary flow within the passage. The iceform endwall has a closer-to-design exit flow pattern than the E3 endwall.

The Influence of Aero-Derivative Combustor Turbulence and Reynolds Number on Vane Aerodynamics Losses, Secondary Flows, and Wake Growth

2006 ◽  
Author(s):  
F. E. Ames ◽  
J. D. Johnson ◽  
N. J. Fiala
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Pressure Loss ◽  
Total Pressure ◽  
Reynolds Numbers ◽  
Secondary Flows ◽  
Total Pressure Loss ◽  
Surface Boundary ◽  
High Turbulence ◽  
Turbulence Condition

Exit surveys detailing total pressure loss, turning angle, and secondary velocities have been acquired for a fully loaded vane profile in a large scale low speed cascade facility. Exit surveys have been taken over a four-to-one range in Reynolds numbers based on exit conditions and for both a low turbulence condition and a high turbulence condition. The high turbulence condition was generated using a mock aero-derivative combustor. Exit loss, angle, and secondary velocity measurements were acquired in the facility using a five-hole cone probe at two stations representing axial chord spacings of 0.25 and 0.50. Substantial differences in the level of losses, distribution of losses, and secondary flow vectors are seen with the different turbulence conditions and at the different Reynolds numbers. The higher turbulence condition produces a significantly broader wake than the low turbulence case and shows a measurable total pressure loss in the region outside the wakes. Generally, total pressure losses are about 0.02 greater for the high turbulence case compared with the low turbulence case primarily due to the state of the suction surface boundary layers. Losses decrease moderately with increasing Reynolds number. Cascade inlet velocity distributions have been previously documented in an endwall heat transfer study of this same geometry. These exit survey measurements support our understanding of the endwall heat transfer distributions, the secondary flows in the passage, and the origin of losses.

Heat Transfer Enhancement for Gas Turbine Blade Leading Edge Cooling Using Curved Double-Wall/Vortex Cooling With Various Disturbing Objects

2019 ◽  
Author(s):  
Xiaojun Fan ◽  
Liang Li ◽  
Jiefeng Wang ◽  
Fan Wu
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Pressure Loss ◽  
Total Pressure ◽  
Leading Edge ◽  
Total Pressure Loss ◽  
Wall Impingement ◽  
Pin Fins ◽  
Cooling Passage ◽  
Double Wall

Abstract A new double-wall cooling configuration combined with the vortex cooling is established to study the cooling behavior for the gas turbine blade leading edge. This configuration consists of multiple nozzles, a curved inner cooling passage, a row of bridge holes and a curved outer cooling passage with 4 kinds of disturbing objects (namely smooth wall, pin-fins, dimples and protrusions). Numerical simulations are performed based on the 3D viscous steady Reynolds Averaged Navier-Stokes (RANS) equations and the k-ω turbulence model. The cooling behavior of the Double-wall/vortex cooling configuration is compared with the Double-wall/impingement cooling configuration at the same conditions. Generally, the Double-wall/vortex cooling configuration has a better cooling performance. It is found the Nusselt number of the inner surface for the Double-wall/vortex cooling configuration is 46.7% higher. However, the Double-wall/impingement cooling configuration has a smaller friction coefficient and a total pressure loss. Different disturbing objects have significant influences on the heat transfer performance of the outer surface. The Nusselt number of disturbing objects (pin-fins, dimples and protrusions) is much higher than the smooth wall, and the value is 1.27–2.22 times larger. Configuration with protrusions has the highest globally-averaged Nusselt number. For the heat transfer performance of the inner surface and the total pressure loss coefficient, disturbing objects have no obvious influence. As bridge holes row increases, the overall cooling performance is improved. The globally-averaged Nusselt number of the outer target is enhanced while the total pressure loss is reduced.

Elliptical Pin Fins as an Alternative to Circular Pin Fins for Gas Turbine Blade Cooling Applications: Part 1 — Endwall Heat Transfer and Total Pressure Loss Characteristics

2001 ◽  
Author(s):  
Oğuz Uzol ◽  
Cengiz Camci
Keyword(s):  
Heat Transfer ◽  
Pressure Loss ◽  
Total Pressure ◽  
Major Axis ◽  
Total Pressure Loss ◽  
Turbine Blade Cooling ◽  
Pin Fin ◽  
Blade Cooling ◽  
Pin Fins ◽  
Pin Fin Arrays

Detailed experimental investigation of the wall heat transfer enhancement and total pressure loss characteristics for two alternative elliptical pin fin arrays is conducted and the results are compared to the conventional circular pin fin arrays. Two different elliptical pin fin geometries with different major axis lengths are tested, both having a minor axis length equal to the circular fin diameter and positioned at zero degrees angle of attack to the free stream flow. The major axis lengths for the two elliptical fins are 1.67 and 2.5 times the circular fin diameter, respectively. The pin fin arrays with H/D = 1.5 are positioned in a staggered 2 row configuration with 3 fins in the first row and 2 fins in the second row with S/D = X/D = 2. Endwall heat transfer and total pressure loss measurements are performed two diameter downstream of the pin fin arrays (X/D = 2) in a rectangular cross-section tunnel with an aspect ratio of 4.8 and for varying Reynolds numbers between 10000 and 47000 based on the inlet velocity and the fin diameter. Liquid Crystal Thermography is used for the measurement of convective heat transfer coefficient distributions on the endwall inside the wake. The results show that the wall heat transfer enhancement capability of the circular pin fin array is about 25–30% higher than the elliptical pin fin arrays in average. However in terms of total pressure loss, the circular pin fin arrays generate 100–200% more pressure loss than the elliptical pin fin arrays. This makes the elliptical fin arrays very promising cooling devices as an alternative to conventional circular pin fin arrays used in gas turbine blade cooling applications.

Sweeping Jet Film Cooling on a Turbine Vane

2018 ◽  
Author(s):  
Mohammad A. Hossain ◽  
Lucas Agricola ◽  
Ali Ameri ◽  
James W. Gregory ◽  
Jeffrey P. Bons
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Pressure Loss ◽  
Total Pressure ◽  
Convective Heat Transfer Coefficient ◽  
Total Pressure Loss ◽  
Pressure Probe ◽  
Blowing Ratio ◽  
Turbine Vane ◽  
Shaped Hole

The cooling performance of sweeping jet film cooling was studied on a turbine vane suction surface in a low-speed linear cascade wind tunnel. The sweeping jet holes consist of fluidic oscillators with an aspect ratio (AR) of unity and a hole spacing of Pd/D = 6. Infrared (IR) thermography was used to estimate the adiabatic film effectiveness at several blowing ratios and two different freestream turbulence levels (Tu = 0.3% and 6.1%). Convective heat transfer coefficient was measured by a transient IR technique, and the net heat flux benefit was calculated. The total pressure loss due to sweeping jet film cooling was characterized by traversing a total pressure probe at the exit plane of the cascade. Tests were performed with a baseline shaped hole (777-shaped hole) for comparison. The sweeping jet hole showed higher adiabatic film effectiveness than the 777-shaped hole in the near hole region. Although the unsteady sweeping action of the jet augments heat transfer, the net positive cooling benefit is higher for sweeping jet holes compared to 777 hole at particular flow conditions. The total pressure loss measurement showed a 12% increase in total pressure loss at a blowing ratio of M = 1.5 for sweeping jet hole while 777-shaped hole showed a 8% total pressure loss increase at the corresponding blowing ratio.

Large Eddy Simulation of Leading Edge Film Cooling—Part II: Heat Transfer and Effect of Blowing Ratio

2008 ◽  
Vol 130 (4) ◽  
Author(s):  
Ali Rozati ◽  
Danesh K. Tafti
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Large Eddy Simulation ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Leading Edge ◽  
Blowing Ratio ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Adiabatic Effectiveness

Detailed investigation of film cooling for a cylindrical leading edge is carried out using large eddy simulation (LES). The paper focuses on the effects of coolant to mainstream blowing ratio on flow features and, consequently, on the adiabatic effectiveness and heat transfer coefficient. With the advantage of obtaining unique, accurate, and dynamic results from LES, the influential coherent structures in the flow are identified. Describing the mechanism of jet-mainstream interaction, it is shown that as the blowing ratio increases, a more turbulent shear layer and stronger mainstream entrainment occur. The combined effects lead to a lower adiabatic effectiveness and higher heat transfer coefficient. Surface distribution and span-averaged profiles are shown for both adiabatic effectiveness and heat transfer (presented by Frossling number). Results are in good agreement with the experimental data of Ekkad et al. [1998, “Detailed Film Cooling Measurement on a Cylindrical Leading Edge Model: Effect of Free-Steam Turbulence and Coolant Density,” ASME J. Turbomach., 120, pp. 799–807].

Sign in / Sign up

Export Citation Format

Share Document