Casing Vibration and Gas Turbine Operating Conditions

1989 ◽  
Author(s):  
K. Mathioudakis ◽  
E. Loukis ◽  
K. D. Papailiou
Keyword(s):  
Gas Turbine ◽  
Transfer Functions ◽  
Parametric Identification ◽  
Fast Response ◽  
Operating Conditions ◽  
Rotor Blades ◽  
Unsteady Pressure ◽  
Signal Features ◽  
Surface Vibrations ◽  
Industrial Gas Turbine

The results from an experimental investigation of the compressor casing vibration of an industrial Gas Turbine are presented. It is demonstrated that statistical properties of acceleration signals can be linked with engine operating conditions. The power content of such signals is dominated by contributions originating from the stages of the compressor, while the contribution of the shaft excitation is secondary. Using non-parametric identification methods, accelerometer outputs are correlated to unsteady pressure measurements taken by fast response transducers at the inner surface of the compressor casing. The transfer functions allow reconstruction of unsteady pressure signal features from the accelerometer readings. A possibility is thus provided, for “seeing” the unsteady pressure field of the rotor blades without actually penetrating through the casing, but by simply observing its external surface vibrations.

Casing Vibration and Gas Turbine Operating Conditions

1990 ◽  
Vol 112 (4) ◽  
pp. 478-485 ◽  
Author(s):  
K. Mathioudakis ◽  
E. Loukis ◽  
K. D. Papailiou
Keyword(s):  
Gas Turbine ◽  
Transfer Functions ◽  
Fast Response ◽  
Operating Conditions ◽  
Rotor Blades ◽  
Unsteady Pressure ◽  
Signal Features ◽  
Power Content ◽  
Surface Vibrations ◽  
Industrial Gas Turbine

The results from an experimental investigation of the compressor casing vibration of an industrial gas turbine are presented. It is demonstrated that statistical properties of acceleration signals can be linked with engine operating conditions. The power content of such signals is dominated by contributions originating from the stages of the compressor, while the contribution of the shaft excitation is secondary. Using nonparametric identification methods, accelerometer outputs are correlated to unsteady pressure measurements taken by fast response transducers at the inner surface of the compressor casing. The transfer functions allow reconstruction of unsteady pressure signal features from the accelerometer readings. A possibility is thus provided for “seeing” the unsteady pressure field of the rotor blades without actually penetrating through the casing, but by simply observing its external surface vibrations.

Fast Response Wall Pressure Measurement as a Means of Gas Turbine Blade Fault Identification

1991 ◽  
Vol 113 (2) ◽  
pp. 269-275 ◽  
Author(s):  
K. Mathioudakis ◽  
A. Papathanasiou ◽  
E. Loukis ◽  
K. Papailiou
Keyword(s):  
Gas Turbine ◽  
Turbine Blade ◽  
Pressure Field ◽  
Fast Response ◽  
Gas Turbine Blade ◽  
Unsteady Pressure ◽  
Rotating Blade ◽  
Processing Techniques ◽  
Industrial Gas Turbine ◽  
Unsteady Pressure Measurements

The distortions of the pressure field around rotating blades of turbomachinery components due to alterations of their shape can be utilized for the identification of faults related to the blading. Measurement of the unsteady pressure field near the wall provides information on such flow and pressure distortions and can thus be used for diagnostic purposes. An experimental investigation of the compressor rotating blade pressure field of an industrial gas turbine has been undertaken, in order to demonstrate the feasibility of the abovementioned principle. Various realistic gas turbine blade faults have been examined. Application of the appropriate processing techniques demonstrates that unsteady pressure measurements can be used to identify the occurrence of minor blade faults (not traceable by standard techniques) as well as the kind of fault. The proposed methodology has the potential for being incorporated in a computerized engine health monitoring system.

Wake, Shock, and Potential Field Interactions in a 1.5 Stage Turbine—Part I: Vane-Rotor and Rotor-Vane Interaction

2003 ◽  
Vol 125 (1) ◽  
pp. 33-39 ◽  
Author(s):  
R. J. Miller ◽  
R. W. Moss ◽  
R. W. Ainsworth ◽  
N. W. Harvey
Keyword(s):  
High Pressure ◽  
Potential Field ◽  
Pressure Field ◽  
Fast Response ◽  
Operating Conditions ◽  
Rotor Blades ◽  
Time Resolved ◽  
Pressure Transducers ◽  
Unsteady Pressure ◽  
The Individual

The composition of the time-resolved surface pressure field around a high-pressure rotor blade caused by the presence of neighboring blade rows is investigated, with the individual effects of wake, shock and potential field interaction being determined. Two test geometries are considered: first, a high-pressure turbine stage coupled with a swan-necked diffuser exit duct; secondly, the same high-pressure stage but with a vane located in the downstream duct. Both tests were conducted at engine-representative Mach and Reynolds numbers, and experimental data was acquired using fast-response pressure transducers mounted on the mid-height streamline of the HP rotor blades. The results are compared to time-resolved computational predictions of the flowfield in order to aid interpretation of experimental results and to determine the accuracy with which the computation predicts blade interaction. The paper is split into two parts: the first investigating the effect of the upstream vane on the unsteady pressure field around the rotor (vane-rotor interaction), and the second investigating the effect of the downstream vane on the unsteady pressure field around the rotor (rotor-vane interaction). The paper shows that at typical design operating conditions shock interaction from the upstream blade row is an order of magnitude greater than wake interaction and that with the design vane-rotor inter-blade gap the presence of the rotor causes a periodic increase in the strength of the vane trailing edge shock. The presence of the potential field of the downstream vane is found to affect significantly the rotor pressure field downstream of the Mach one surface within each rotor passage.

Fast Response Wall Pressure Measurement as a Means of Gas Turbine Blade Fault Identification

1990 ◽  
Author(s):  
K. Mathioudakis ◽  
A. Papathanasiou ◽  
E. Loukis ◽  
K. Papailiou
Keyword(s):  
Gas Turbine ◽  
Turbine Blade ◽  
Pressure Field ◽  
Fast Response ◽  
Gas Turbine Blade ◽  
Rotating Blades ◽  
Unsteady Pressure ◽  
Processing Techniques ◽  
Industrial Gas Turbine ◽  
Unsteady Pressure Measurements

The distortions of the pressure field around rotating blades of turbomachinery components due to alterations of their shape, can be utilized for the identification of faults related to the blading. Measurement of the unsteady pressure field in the wall proximity, provides information on such flow and pressure distortions and can thus be used for diagnostic purposes. An experimental investigation of the compressor rotating blades pressure field of an industrial gas turbine has been undertaken, in order to demonstrate the feasibility of the above mentioned principle. Various realistic gas turbine blade faults have been examined. The application of the appropriate processing techniques, demonstrates that unsteady pressure measurements can be used to identify the occurrence of minor blade faults (not traceable by standard techniques) as well as the kind of the fault. The proposed methodology has the potential for being incorporated in a computerized engine health monitoring system.

Wake, Shock and Potential Field Interactions in a 1.5 Stage Turbine: Part I — Vane-Rotor and Rotor-Vane Interaction

2002 ◽  
Author(s):  
R. J. Miller ◽  
R. W. Moss ◽  
R. W. Ainsworth ◽  
N. W. Harvey
Keyword(s):  
High Pressure ◽  
Potential Field ◽  
Pressure Field ◽  
Fast Response ◽  
Operating Conditions ◽  
Rotor Blades ◽  
Time Resolved ◽  
Pressure Transducers ◽  
Unsteady Pressure ◽  
The Individual

The composition of the time-resolved surface pressure field around a high-pressure rotor blade caused by the presence of neighboring blade rows is investigated, with the individual effects of wake, shock and potential field interaction being determined. Two test geometries are considered: first, a high-pressure turbine stage coupled with a swan-necked diffuser exit duct; secondly, the same high-pressure stage but with a vane located in the downstream duct. Both tests were conducted at engine-representative Mach and Reynolds numbers, and experimental data was acquired using fast-response pressure transducers mounted on the mid-height streamline of the HP rotor blades. The results are compared to time-resolved computational predictions of the flowfield in order to aid interpretation of experimental results and to determine the accuracy with which the computation predicts blade interaction. The paper is split into two parts, the first investigating the effect of the upstream vane on the unsteady pressure field around the rotor (vane-rotor interaction) and the second investigating the effect of the downstream vane on the unsteady pressure field around the rotor (rotor-vane interaction). The paper shows that at typical design operating conditions shock interaction from the upstream blade row is an order of magnitude greater than wake interaction and that with the design vane-rotor inter-blade gap the presence of the rotor causes a periodic increase in the strength of the vane trailing edge shock. The presence of the potential field of the downstream vane is found to affect significantly the rotor pressure field downstream of the Mach one surface within each rotor passage.

scholarly journals The Design and Evaluation of a 14 Stage, 16:1 Pressure Ratio Compressor for an Industrial Gas Turbine

1996 ◽  
Author(s):  
Mohammad R. Saadatmand
Keyword(s):  
Experimental Data ◽  
Gas Turbine ◽  
Rotor Blade ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Suction Surface ◽  
Design Intent ◽  
Flow Through ◽  
Industrial Gas Turbine

The aerodynamic design process leading to the production configuration of a 14 stage, 16:1 pressure ratio compressor for the Taurus 70 gas turbine is described. The performance of the compressor is measured and compared to the design intent. Overall compressor performance at the design condition was found to be close to design intent. Flow profiles measured by vane mounted instrumentation are presented and discussed. The flow through the first rotor blade has been modeled at different operating conditions using the Dawes (1987) three-dimensional viscous code and the results are compared to the experimental data. The CFD prediction agreed well with the experimental data across the blade span, including the pile up of the boundary layer on the corner of the hub and the suction surface. The rotor blade was also analyzed with different grid refinement and the results were compared with the test data.

Measurement and Analysis of Flame Transfer Function in a Sector Combustor Under High Pressure Conditions

2003 ◽  
Author(s):  
W. S. Cheung ◽  
G. J. M. Sims ◽  
R. W. Copplestone ◽  
J. R. Tilston ◽  
C. W. Wilson ◽  
...  
Keyword(s):  
High Pressure ◽  
Transfer Function ◽  
Heat Release ◽  
Gas Turbine ◽  
Mass Flow ◽  
Atmospheric Pressure ◽  
Acoustic Waves ◽  
Gas Turbines ◽  
Transfer Functions ◽  
Unsteady Pressure

Lean premixed prevaporised (LPP) combustion can reduce NOx emissions from gas turbines, but often leads to combustion instability. A flame transfer function describes the change in the rate of heat release in response to perturbations in the inlet flow as a function of frequency. It is a quantitative assessment of the susceptibility of combustion to disturbances. The resulting fluctuations will in turn generate more acoustic waves and in some situations self-sustained oscillations can result. Flame transfer functions for LPP combustion are poorly understood at present but are crucial for predicting combustion oscillations. This paper describes an experiment designed to measure the flame transfer function of a simple combustor incorporating realistic components. Tests were conducted initially on this combustor at atmospheric pressure (1.2 bar and 550 K) to make an early demonstration of the combustion system. The test rig consisted of a plenum chamber with an inline siren, followed by a single LPP premixer/duct and a combustion chamber with a silencer to prevent natural instabilities. The siren was used to induce variable frequency pressure/acoustic signals into the air approaching the combustor. Both unsteady pressure and heat release measurements were undertaken. There was good coherence between the pressure and heat release signals. At each test frequency, two unsteady pressure measurements in the plenum were used to calculate the acoustic waves in this chamber and hence estimate the mass-flow perturbation at the fuel injection point inside the LPP duct. The flame transfer function relating the heat release perturbation to this mass flow was found as a function of frequency. The same combustor hardware and associated instrumentation were then used for the high pressure (15 bar and 800 K) tests. Flame transfer function measurements were taken at three combustion conditions that simulated the staging point conditions (Idle, Approach and Take-off) of a large turbofan gas turbine. There was good coherence between pressure and heat release signals at Idle, indicating a close relationship between acoustic and heat release processes. Problems were encountered at high frequencies for the Approach and Take-off conditions, but the flame transfer function for the Idle case had very good qualitative agreement with the atmospheric-pressure tests. The flame transfer functions calculated here could be used directly for predicting combustion oscillations in gas turbine using the same LPP duct at the same operating conditions. More importantly they can guide work to produce a general analytical model.

Experimental Assessment of the Emissions Benefits of a Ceramic Gas Turbine Combustor

1996 ◽  
Author(s):  
K. O. Smith ◽  
A. Fahme
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Flow Distribution ◽  
Operating Conditions ◽  
Nox Emissions ◽  
Fuel Injector ◽  
Gas Turbine Combustor ◽  
Experimental Assessment ◽  
Industrial Gas Turbine ◽  
Combustor Liner

Three subscale, cylindrical combustors were rig tested on natural gas at typical industrial gas turbine operating conditions. The intent of the testing was to determine the effect of combustor liner cooling on NOx and CO emissions. In order of decreasing liner cooling, a metal louvre-cooled combustor, a metal effusion-cooled combustor, and a backside-cooled ceramic (CFCC) combustor were evaluated. The three combustors were tested using the same lean-premixed fuel injector. Testing showed that reduced liner cooling produced lower CO emissions as reaction quenching near the liner wall was reduced. A reduction in CO emissions allows a reoptimization of the combustor air flow distribution to yield lower NOx emissions.

Numerical and Experimental Evaluation of a Dual-Fuel Dry-Low-NOx Micromix Combustor for Industrial Gas Turbine Applications

2018 ◽  
Vol 11 (1) ◽  
Author(s):  
Harald H. W. Funke ◽  
Nils Beckmann ◽  
Jan Keinz ◽  
Sylvester Abanteriba
Keyword(s):  
Gas Turbine ◽  
Combustion Process ◽  
Experimental Studies ◽  
Research Process ◽  
Operating Conditions ◽  
Experimental Investigations ◽  
Dual Fuel ◽  
Pure Hydrogen ◽  
Ongoing Research ◽  
Industrial Gas Turbine

Abstract The dry-low-NOx (DLN) micromix combustion technology has been developed originally as a low emission alternative for industrial gas turbine combustors fueled with hydrogen. Currently, the ongoing research process targets flexible fuel operation with hydrogen and syngas fuel. The nonpremixed combustion process features jet-in-crossflow-mixing of fuel and oxidizer and combustion through multiple miniaturized flames. The miniaturization of the flames leads to a significant reduction of NOx emissions due to the very short residence time of reactants in the flame. The paper presents the results of a numerical and experimental combustor test campaign. It is conducted as part of an integration study for a dual-fuel (H2 and H2/CO 90/10 vol %) micromix (MMX) combustion chamber prototype for application under full scale, pressurized gas turbine conditions in the auxiliary power unit Honeywell Garrett GTCP 36-300. In the presented experimental studies, the integration-optimized dual-fuel MMX combustor geometry is tested at atmospheric pressure over a range of gas turbine operating conditions with hydrogen and syngas fuel. The experimental investigations are supported by numerical combustion and flow simulations. For validation, the results of experimental exhaust gas analyses are applied. Despite the significantly differing fuel characteristics between pure hydrogen and hydrogen-rich syngas, the evaluated dual-fuel MMX prototype shows a significant low NOx performance and high combustion efficiency. The combustor features an increased energy density that benefits manufacturing complexity and costs.

scholarly journals Experimental Assessment of Fouling Effects in a Multistage Axial Compressor

2020 ◽  
Vol 197 ◽  
pp. 11007
Author(s):  
Nicola Casari ◽  
Michele Pinelli ◽  
Pier Ruggero Spina ◽  
Alessio Suman ◽  
Alessandro Vulpio
Keyword(s):  
Gas Turbine ◽  
Axial Compressor ◽  
Operating Conditions ◽  
Rotor Blades ◽  
Small Scale ◽  
Performance Loss ◽  
Machine Performance ◽  
Internal Surfaces ◽  
Analysis Package ◽  
Multistage Axial Compressor

The study of the adhesion of micro sized particles to gas turbine internal surfaces, commonly known as gas turbine fouling, has gained increasing attention in the last years due to its dramatic effect on machine performance and reliability. On-field fouling analysis is mostly related to visual inspections during overhaul and/or programmed stops, which are performed, in particular, when gas turbine performance degradation falls under predetermined thresholds. However, these analyses, even if performed in the most complete as possible way, are rarely (or never) related to the conditions under which the gas turbine contamination takes place since the affecting parameters are difficult or even impossible to be adequately monitored. In the present work, a small scale multistage axial compressor is used to experimentally simulate the fouling phenomenon. The test rig allows the accurate control of the most relevant operating parameters which influence the fouling phenomenon. The compressor performance loss due to particle contamination has been quantitatively assessed. Soot particles appear stickier, especially in the presence of high humidity, and represent the most harmful operating conditions for the compressor unit. The deposits on the stator vanes and the rotor blades have been detected and post-processed, highlighting the most affected regions of each compressor stage employing an image analysis package tool.

Sign in / Sign up

Export Citation Format

Share Document