scholarly journals Numerical Simulation of the Flow Field Around Supersonic Air-Intakes

1992 ◽  
Author(s):  
G. Freskos ◽  
O. Penanhoat
Keyword(s):  
Flow Field ◽  
Experimental Studies ◽  
Navier Stokes ◽  
Complex Flow ◽  
Grid Approach ◽  
Parametric Studies ◽  
Entire Flow ◽  
Flow Configurations ◽  
Cost Efficient ◽  
Aircraft Aerodynamics

The demand for efficiency in today’s and in future civil aircraft is such that experimental studies alone do not suffice to optimize aircraft aerodynamics. In this context, much effort has been spent in the past decade to develop numerical methods capable of reproducing the phenomena that occur in the engine flow field. This paper presents some studies in Computational Fluid Dynamics related to supersonic inlets. Two approaches are considered. First, there is a need for code capable of calculating in a cost-efficient way the entire flow field around a 2D or 3D inlet, e.g. to perform parametric studies. To this effect, a computing method based on grid construction by mesh generator dedicated to inlet shapes and on the discretization of the unsteady Euler equations with an explicit upwind scheme was developed. The treatment of complex geometries led us to adopt a multiblock grid approach. Therefore particular attention was paid to the treatment of the boundary conditions between the different domains. Secondly, there is a need for code that can capture local phenomena in order to get a better understanding of inlet behaviour (shock/shock, shock/boundary layer interactions, etc.). To this effect a 2D turbulent Navier-Stokes code is used. The 2 equations k-ε turbulence model included in the program seems to be one of the most successful models for calculating flow realistically. Correction of the near-wall influence extends its capability to complex flow configurations, e.g. those with separated zones.

Numerical Simulation of the Flow Field Around Supersonic Air-Intakes

1994 ◽  
Vol 116 (1) ◽  
pp. 116-123 ◽  
Author(s):  
G. Freskos ◽  
O. Penanhoat
Keyword(s):  
Flow Field ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Two Dimensional ◽  
Complex Flow ◽  
Grid Approach ◽  
Entire Flow ◽  
Flow Configurations ◽  
Cost Efficient

The demand for efficiency in today’s and in future civil aircraft is such that experimental studies alone do not suffice to optimize aircraft aerodynamics. In this context, much effort has been spent in the past decade to develop numerical methods capable of reproducing the phenomena that occur in the engine flow field. This paper presents some studies in Computational Fluid Dynamics related to supersonic inlets. Two approaches are considered. First, there is a need for a code capable of calculating in a cost-efficient way the entire flow field around a two-dimensional or three-dimensional inlet, e.g., to perform parametric studies. To this effect, a computing method based on grid construction by mesh generator dedicated to inlet shapes and on the discretization of the unsteady Euler equations with an explicit upwind scheme was developed. The treatment of complex geometries led us to adopt a multiblock grid approach. Therefore particular attention was paid to the treatment of the boundary conditions between the different domains. Second, there is a need for a code that can capture local phenomena in order to get a better understanding of inlet behavior (shock/shock, shock/boundary layer interactions, etc.). To this effect a two-dimensional turbulent Navier-Stokes code is used. The two-equation k-ε turbulence model included in the program seems to be one of the most successful models for calculating flow realistically. Correction of the near-wall influence extends its capability to complex flow configurations, e.g., those with separated zones.

RANS Maneuvering Simulation of Esso Osaka With Rudder and a Body-Force Propeller

2005 ◽  
Vol 49 (02) ◽  
pp. 98-120
Author(s):  
Claus D. Simonsen ◽  
Frederick Stern
Keyword(s):  
Flow Field ◽  
Open Water ◽  
Verification And Validation ◽  
Fair Agreement ◽  
Navier Stokes ◽  
Complex Flow ◽  
Flow Problems ◽  
The Difference ◽  
Propeller Geometry ◽  
Flow Study

A simplified potential theory-based infinite-bladed propeller model is coupled with the Reynolds averaged Navier-Stokes (RANS) code CFDSHIP-IOWA to give a model that interactively determines propeller-hull-rudder interaction without requiring detailed modeling of the propeller geometry. Computations are performed for an open-water propeller, for the Series 60 ship sailing straight ahead and for the appended tanker Esso Osaka in different maneuvering conditions. The results are compared with experimental data, and the tanker data are further used to study the interaction among the propeller, hull, and rudder. A comparison between calculated and measured data for the Series 60 ship shows fair agreement, where the computation captures the trends in the flow, that is, the flow structure and the magnitude of the field quantities together with the integral quantities. For the tanker, the flow study reveals a rather complex flow field in the stern region, where the velocity distribution and propeller loading reflect the flow field changes caused by the different maneuvering conditions. The integral quantities, that is, the propeller, hull, and rudder forces, are in fair agreement with experiments. No formal verification and validation are performed, so the present results are related to previous work with verification and validation of the same model, but without the propeller. For the validated cases, the levels of validation are the same as without the propeller, because the validation uncertainties, that is, the combined experimental and simulation uncertainties, are assumed to be the same for both cases. Based on this, validation is obtained for approximately the same cases as for the without-propeller conditions, but the comparison errors, that is, the difference between experiment and calculation, are different. For instance, the difference between computation and experiment for the ship resistance is generally larger with the propeller than without, whereas the opposite is the case for the rudder drag. Summarizing the results, the method shows encouraging results, and taking the effort related to modeling the propeller into account, the method appears to be useful in connection with studies of rudder-propeller-hull related flow problems, where the real propeller geometry cannot be modeled.

Navier-Stokes Computation on a Pivoting Doors Thrust Reverser and Comparison With Tests

1992 ◽  
Author(s):  
L. Schreiber ◽  
M. Legras
Keyword(s):  
Flow Field ◽  
Complex Geometry ◽  
Numerical Data ◽  
Navier Stokes ◽  
Complex Flow ◽  
Static Test ◽  
Development Delay ◽  
Cfd Method ◽  
Thrust Reverser ◽  
Reverse Thrust

An engine thrust reverser must meet different aerodynamic requirements to take into account the engine and airplane integration. These requirements are: - Control of the exit area in order to assess a convenient engine compatibility during the reverser operation. - Generation of reverse thrust meeting the level specified by the airframe in order to slowdown the airplane. - Mimization of the reversed flow field interaction with the airplane structure such as wing and shutters. - Avoid the flow reingestion by the engine fan. In order to reduce the tests number, to decrease the development delay and to improve aerodynamic performance, SNECMA group (SNECMA and HISPANO-SUIZA) has decided to develop a CFD method adapted to pivoting doors thrust reverser aerodynamic calculation. This method uses a Navier-Stokes 3D solver (PHOENICS code) well adapted to complex geometry and complex flow field. The mesh is generated with an analytical method and only one domain is used. The computation has been completed assuming laminar viscosity. The numerical data got with this method have been compared to static test realized on a model similar to actual CFM56-5C four doors reverser. The comparison parameters are the static pressure on the doors, the flow rate and the axial reverse thrust.

URANS Simulation of an Appended Hull During Steady Turn With Propeller Represented by an Actuator Disk Model

2011 ◽  
Author(s):  
Charles M. Dai ◽  
Ronald W. Miller
Keyword(s):  
Flow Field ◽  
Cross Flow ◽  
Field Measurements ◽  
Navier Stokes ◽  
Experimental Measurements ◽  
Complex Flow ◽  
Ship Maneuvering ◽  
Disk Model ◽  
Actuator Disk ◽  
Propeller Wake

This paper reports on the comparison between computational simulations and experimental measurements of a surface vessel in steady turning conditions. The primary purpose of these efforts is to support the development of physics-based high fidelity maneuvering simulation tools by providing accurate and reliable hydrodynamic data with relevance to maneuvering performances. Reynolds Averaged Unsteady Navier Stokes Solver (URANS): CFDSHIPIOWA was used to perform simulations for validation purposes and for better understanding of the fundamental flow physics of a hull under maneuvering conditions. The Propeller effects were simulated using the actuator disk model included in CFDShip-Iowa. The actuator disk model prescribes a circumferential averaged body force with axial and tangential components. No propeller generated side forces are accounted for in the model. This paper examines the effects of actuator disk model on the overall fidelity of a RANS based ship maneuvering simulations. Both experiments and simulations provide physical insights into the complex flow interactions between the hull and various appendages, the rudders and the propellers. The experimental effort consists of flow field measurements using Stereo Particle-Image Velocimetry (SPIV) in the stern region of the model and force and moment measurements on the whole ship and on ship components such as the bilge keels, the rudders, and the propellers. Comparisons between simulations and experimental measurements were made for velocity distributions at different transverse planes along the ship axis and different forces components for hull, appendages and rudders. The actuator disk model does not predict any propeller generated side forces in the code and they need to be taken into account when comparing hull and appendages generated side forces in the simulations. The simulations were compared with experimental results and they both demonstrate the cross flow effect on the transverse forces and the propeller slip streams generated by the propellers during steady turning conditions. The hull forces (include hull, bilge keels, skeg, shafting and strut) predictions were better for large turning circle case as compared with smaller turning circle. Despite flow field simulations appear to capture gross flow features qualitatively; detailed examinations of flow distributions reveal discrepancies in predictions of propeller wake locations and secondary flow structures. The qualitative comparisons for the rudders forces also reveal large discrepancies and it was shown that the primary cause of discrepancies is due to poor predictions of velocity inflow at the rudder plane.

Experimental and Numerical Investigation of Stator Exit Flow Field of an Automotive Torque Converter

1996 ◽  
Vol 118 (4) ◽  
pp. 835-843 ◽  
Author(s):  
B. V. Marathe ◽  
B. Lakshminarayana ◽  
Y. Dong
Keyword(s):  
Flow Field ◽  
Secondary Flow ◽  
Numerical Investigation ◽  
Three Dimensional ◽  
Axial Flow ◽  
Torque Converter ◽  
Operating Conditions ◽  
Navier Stokes ◽  
Complex Flow ◽  
Rate Of Decay

The objective of this investigation is to understand the nature of the complex flow field inside each element of the torque converter through a systematic experimental and numerical investigation of the flow field. A miniature five-hole probe was used to acquire the data at the exit of the stator at several operating conditions. The flow field is found to be highly three dimensional with substantial flow deviations, and secondary flow at the exit of the stator. The secondary flow structure, caused by the upstream radial variation of the through flow, induces flow overturning near the core. Flow separation near the shell causes flow underturning in this region. The rate of decay of stator wake is found to be slower than that observed in the wakes of axial flow turbine nozzles. The flow predictions by a Navier–Stokes code are in good agreement with the pressure and the flow field measured at the exit of the stator at the design and the off-design conditions.

Structure of the Flow Field of a Nonpremixed Gas Jet Flame in Cross-Flow

1997 ◽  
Vol 119 (2) ◽  
pp. 137-144 ◽  
Author(s):  
O. Savas ◽  
R. F. Huang ◽  
S. R. Gollahalli
Keyword(s):  
Flow Field ◽  
Flame Structure ◽  
Experimental Studies ◽  
Power Spectra ◽  
Cross Flow ◽  
Flux Ratio ◽  
Quantitative Information ◽  
Turbulent Flames ◽  
Complex Flow ◽  
Jet Flame

Experimental studies on nonpremixed turbulent flames in cross flow are necessary as the current analytical and numerical tools are unable to provide acceptable quantitative information about their complex flow fields. This study, which complements the results of a previous study by the authors on the flame structure in the stabilization region of a partially lifted turbulent diffussion flame in cross-flow (TDFCF), presents the measured turbulence quantities in the flow field of the same flame. Results include mean velocities in the cross-stream and spanwise directions, the vertical and horizontal components of fluctuating components of velocity, Reynolds stress, power spectra, and autocorrelations useful for developing and validating theoretical models of TDFCF in the moderate momentum flux ratio range

Experimental Investigation of a Generic Compressor Bleed System

2006 ◽  
Author(s):  
Reinaldo A. Gomes ◽  
Carsten Schwarz ◽  
Michael Pfitzner
Keyword(s):  
Flow Field ◽  
Annular Flow ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Dimensional Model ◽  
Three Dimensional Model ◽  
Complex Flow ◽  
Pressure Losses ◽  
Aero Engines

Extensive experimental studies on axial compressor bleed-flow systems have been carried out on a three dimensional model of a generic bleed-flow configuration typical for aero engines. The compressor flow is modeled as a clean annular flow. One row of stator vanes is used to impart a constant swirl upstream of the bleed system. The rig is designed modularly in order to allow for inexpensive changes in all of its components and therefore to enlarge the variability of the model. The research is focused onto the generation of an experimental data base, which can be used to derive correlations for the calculation of effective areas and pressure losses. Those data are gained using steady pneumatic measurement technique. In addition, the highly complex flow field in the manifold, which has an important effect onto the bleed-flow, is analyzed using Doppler-Global-Velocimetry (DGV). These measurements were conducted in collaboration with DLR Cologne, who have developed the DGV technique. In this paper the flow field in the manifold is analyzed in detail for two different configurations featuring two and four bleed ducts, respectively. Furthermore the use of a flush design of the slot is compared with a lip design. These data are compared to results from the literature achieved using 2-dimensional configurations.

Numerical Prediction of Wakes in Cascades and Compressor Rotors Including the Effects of Mixing: Part I — Cascade Wakes Including the Effects of Incidence and Freestream Turbulence

1991 ◽  
Author(s):  
N. Suryavamshi ◽  
B. Lakshminarayana
Keyword(s):  
Flow Field ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Freestream Turbulence ◽  
Compressor Cascade ◽  
Pressure Loss Coefficient ◽  
Viscous Losses ◽  
Rate Of Decay ◽  
Entire Flow ◽  
High Reynolds

The results of a numerical investigation to predict the flow in the wake regions of compressor cascades, and wakes and mixing in rotors are presented in this paper. Part I deals with flow in compressor cascades including the effects of change in loading (incidence) and the inlet freestream turbulence intensity. Part II of the paper deals with the predictions of the rotor flow field, including wakes and spanwise mixing. The wake behaviour has been studied numerically using a three-dimensional incompressible Navier-Stokes solver with a high Reynolds number form of the k–ε turbulence model. The equations are solved using a time dependent implicit technique. The agreement between the measured data and predictions is good; including the wake profile, decay, and losses. The ability of the pseudo-compressibility scheme to predict the entire flow field including the wake profile and its decay characteristics, effect of loading and the viscous losses of a compressor cascade is demonstrated. The numerical analysis shows a slight increase in the total pressure loss coefficient through the cascade with increasing turbulence levels. The results also show a slight increase in the rate of decay of the wake at higher turbulence levels but the change in the spreading of the wake was found to be very small with increased turbulence levels.

scholarly journals Numerical Prediction of Wakes in Cascades and Compressor Rotors Including the Effects of Mixing: Part II — Rotor Passage Flow and Wakes Including the Effects of Spanwise Mixing

1991 ◽  
Author(s):  
N. Suryavamshi ◽  
B. Lakshminarayana
Keyword(s):  
Flow Field ◽  
Three Dimensional ◽  
Axial Flow ◽  
Radial Component ◽  
Navier Stokes ◽  
Mean Velocity ◽  
Compressor Rotor ◽  
Entire Flow ◽  
High Reynolds ◽  
Flow Compressor

The results of a numerical investigation to predict the flow field including wakes and mixing in axial flow compressor rotors has been presented in this paper. The wake behaviour in a moderately loaded compressor rotor has been studied numerically using a three-dimensional incompressible Navier-Stokes solver with a high Reynolds number form of the k–ε turbulence model. The equations are solved using a time dependent implicit technique. The agreement between the measured data and the predictions are good; including the blade boundary layer profiles, wake mean velocity profiles and decay. The ability of the pseudo-compressibility scheme to predict the entire flow field including the near and far wake profiles and its decay characteristics, effect of loading and the viscous losses of a three-dimensional rotor flow field has been demonstrated. An analysis of the passage averaged velocities and the pressure coefficients shows that the mixing in the downstream regions away from the hub and annulus walls is dominated by wake diffusion. In regions away from the walls, the radial mixing is predominantly caused by the transport of mass, momentum and energy by the radial component of velocity in the wake.

Investigation of Incompressible Flow Past Two Circular Cylinders of Different Diameters

2017 ◽  
Vol 67 (5) ◽  
pp. 487
Author(s):  
Yogesh Bhumkar ◽  
Priyank Kumar ◽  
Arnab Roy ◽  
Sudip Das ◽  
Jai Kumar Prasad
Keyword(s):  
Reynolds Number ◽  
Flow Field ◽  
Circular Cylinders ◽  
Navier Stokes ◽  
Complex Flow ◽  
Convective Boundary ◽  
Flow Past ◽  
Flow Features ◽  
Finite Volume Approach ◽  
Different Diameters

<p>A two - dimensional Navier-Stokes solver based on finite volume approach using a boundary-fitted curvilinear structured O-grid has been developed to obtain details of unconfined flow past cylinders at low Reynolds number of 100 and 200 based on diameter. Computations made on a single cylinder with smaller domain adopting the convective boundary conditions captured most of the flow features. This concept of a smaller domain, when used to capture the highly complex flow field around two cylinders of the same diameter placed in tandem at a Reynolds number of 200 showed reasonable results. The details of the flow field around two cylinders of different diameters placed at a typical distance of 3L and Reynolds number of 100 could be well captured adopting smaller domain concept. It is observed that the change in diameter of upstream cylinder strongly influences the overall flow field and the drag of the downstream cylinder.</p>

Sign in / Sign up

Export Citation Format

Share Document