Multi-Cylinder HCCI Control With Cam Phaser Variable Valve Actuation Using Model Predictive Control

2012 ◽  
Author(s):  
Stephen M. Erlien ◽  
Adam F. Jungkunz ◽  
J. Christian Gerdes
Keyword(s):  
Model Predictive Control ◽  
Predictive Control ◽  
Variable Valve Actuation ◽  
Variable Valve ◽  
Valve Actuation

Model predictive control of HCCI using variable valve actuation and fuel injection

2012 ◽  
Vol 20 (4) ◽  
pp. 421-430 ◽  
Author(s):  
Nikhil Ravi ◽  
Hsien-Hsin Liao ◽  
Adam F. Jungkunz ◽  
Anders Widd ◽  
J. Christian Gerdes
Keyword(s):  
Model Predictive Control ◽  
Predictive Control ◽  
Fuel Injection ◽  
Variable Valve Actuation ◽  
Variable Valve ◽  
Valve Actuation

Potential of the Variable Valve Actuation (VVA) Strategy on a Heavy Duty CNG Engine

2014 ◽  
Author(s):  
Mirko Baratta ◽  
Roberto Finesso ◽  
Daniela Misul ◽  
Ezio Spessa ◽  
Yifei Tong ◽  
...  
Keyword(s):  
Fuel Consumption ◽  
Operating Conditions ◽  
Intake Valve ◽  
Heavy Duty ◽  
Engine Emissions ◽  
Variable Valve Actuation ◽  
Cng Engine ◽  
Variable Valve ◽  
Working Point ◽  
Valve Actuation

The environmental concerns officially aroused in 1970s made the control of the engine emissions a major issue for the automotive industry. The corresponding reduction in fuel consumption has become a challenge so as to meet the current and future emission legislations. Given the increasing interest retained by the optimal use of a Variable Valve Actuation (VVA) technology, the present paper investigates into the potentials of combining the VVA solution to CNG fuelling. Experiments and simulations were carried out on a heavy duty 6-cylinders CNG engine equipped with a turbocharger displaying a twin-entry waste-gate-controlled turbine. The analysis aimed at exploring the potentials of the Early Intake Valve Closure (EIVC) mode and to identify advanced solutions for the combustion management as well as for the turbo-matching. The engine model was developed within the GT-Power environment and was finely tuned to reproduce the experimental readings under steady state operations. The 0D-1D model was hence run to reproduce the engine operating conditions at different speeds and loads and to highlight the effect of the VVA on the engine performance as well as on the fuel consumption and engine emissions. Pumping losses proved to reduce to a great extent, thus decreasing the brake specific fuel consumption (BSFC) with respect to the throttled engine. The exhaust temperature at the turbine inlet was kept to an almost constant value and minor variations were allowed. This was meant to avoid an excessive worsening in the TWC working conditions, as well as deterioration in the turbocharger performance during load transients. The numerical results also proved that full load torque increases can be achieved by reducing the spark advance so that a higher enthalpy is delivered to the turbocharger. Similar torque levels were also obtained by means of Early Intake Valve Closing strategy. For the latter case, negligible penalties in the fuel consumption were detected. Moreover, for a given combustion phasing, the IVC angle directly controls the mass-flow rate and thus the torque. On the other hand, a slight dependence on the combustion phasing can be detected at part load. Finally, the simulations assessed for almost constant fuel consumption for a wide range of IVC and SA values. Specific attention was also paid to the turbocharger group functioning and to its correct matching to the engine working point. The simulations showed that the working point on the compressor map can be optimized by properly setting the spark advance (SA) as referred to the adopted intake-valve closing angle. It is anyhow worth observing that the engine high loads set a constraint deriving from the need to meet the limits on the peak firing pressure (PFP), thus limiting the possibility to optimize the working point once the turbo-matching is defined.

scholarly journals Research on Homogeneous Charge Compression Ignition Combustion of Intake Port Exhaust Gas Recirculation Based on Cam Drive Hydraulic Variable Valve Actuation Mechanism

Energies ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 438
Author(s):  
Linghai Han ◽  
Jiaquan Duan ◽  
Dingchao Qian ◽  
Yanfeng Gong ◽  
Yaodong Wang ◽  
...  
Keyword(s):  
Engine Speed ◽  
Valve Lift ◽  
Intake Port ◽  
Cyclic Variation ◽  
Response Characteristics ◽  
Variable Valve Actuation ◽  
Hcci Combustion ◽  
Variation Range ◽  
Variable Valve ◽  
Valve Actuation

The thermal efficiency of an efficient gasoline engine is only about 40% and it will produce a large number of harmful products. Curbing harmful emissions and enhancing thermal efficiency have always been the goals pursued and emission regulations are also being tightened gradually. As one of the main consumers of fossil fuels, automobile engines must further reduce fuel consumption and emissions to comply with the concept of low-carbon development, which will also help them compete with electric vehicles. Homogeneous charge compression ignition (HCCI) combustion combined with variable valve actuation (VVA) technology is one of the important ways to improve engine emissions and economy. HCCI combustion based on VVA can only be realized at small and medium loads. The actual application on the entire vehicle needs to be combined with spark ignition (SI) combustion to achieve full working condition coverage. Therefore, HCCI combustion needs fast valve response characteristics; however, the valve lift and timing of the existing VVA mechanisms are mostly controlled separately, resulting in poor valve response. In order to solve this problem, the cam driven hydraulic variable valve actuation (CDH-VVA) mechanism was designed. The valve lift and timing can be adjusted at the same time and the switching of valve lift and timing can be completed in 1~2 cycles. A set of combustion mode switching data is selected to show the response characteristics of the CDH-VVA mechanism. When switching from spark ignition (SI) to HCCI, it switches to HCCI combustion after only one combustion cycle and it switches to stable HCCI combustion after two combustion cycles, which proves the fast response characteristics of the CDH-VVA mechanism. At the same time, the CDH-VVA mechanism can form the intake port exhaust gas recirculation (EGR), as one type of internal EGR. This paper studies the HCCI combustion characteristics of the CDH-VVA mechanism in order to optimize it in the future and enable it to realize more forms of HCCI combustion. At 1000 rpm, if the maximum lift of the exhaust valve (MLEV) is higher than 5.0 mm or lower than 1.5 mm, HCCI combustion cannot operate stably, the range of excess air coefficient (λ) is largest when the MLEV is 4.5 mm, ranging from 1.0~1.5. Then, as the MLEV decreases, the range of λ becomes smaller. When the MLEV drops to 1.5 mm, the range of λ shortens to 1.0~1.3. The maximum value of the MLEV remains the same at the three engine speeds (1000 rpm, 1200 rpm and 1400 rpm), which is 5.0 mm. The minimum value of the MLEV gradually climbs as the engine speed increase, 1000 rpm: 1.5 mm, 1200 rpm: 2.0 mm, 1400 rpm: 3.0 mm. With the increase of engine speed, the range of indicated mean effective pressure (IMEP) gradually declines, 3.53~6.31 bar (1000 rpm), 4.11~6.75 bar (1200 rpm), 5.02~6.09 bar (1400 rpm), which proves that the HCCI combustion loads of the intake port EGR are high and cannot be extended to low loads. The cyclic variation of HCCI combustion basically climbs with the decrease of the MLEV and slightly jumps with the increase of the engine speed. At 1000 rpm, when the MLEV is 5.0 mm, the cyclic variation range is 0.94%~1.5%. As the MLEV drops to 1.5 mm, the cyclic variation range rises to 3.5%~4.5%. Taking the maximum value of the MLEV as an example, the cyclic variation range of 1000 rpm is 0.94%~1.5%, 1200 rpm becomes 1.5%~2.3% and 1400 rpm rises to 2.0%~2.5%.

Potentials of a mechanical fully variable valve actuation at boosted SI engines with Direct Injection

MTZ worldwide ◽  
2011 ◽  
Vol 72 (7-8) ◽  
pp. 66-71
Author(s):  
Rudolf Flierl ◽  
Mark Paulov ◽  
Stephan Schmitt ◽  
Fatih Sarikoc ◽  
Ulrich Spicher
Keyword(s):  
Direct Injection ◽  
Variable Valve Actuation ◽  
Si Engines ◽  
Variable Valve ◽  
Valve Actuation
Sign in / Sign up

Export Citation Format

Share Document