Performance Simulation of a Combined Cycle Power Generation System With Steam Injection in the Gas Turbine Combustion Chamber

2007 ◽  
Author(s):  
B. Law ◽  
B. V. Reddy
Keyword(s):  
Combustion Chamber ◽  
Gas Turbine ◽  
Thermal Efficiency ◽  
Pressure Ratio ◽  
Steam Injection ◽  
Combined Cycle ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Work Output ◽  
Gas Turbine Combustion

In the present work the effect of steam injection in the gas turbine combustion chamber is investigated on gas turbine and steam turbine work output and on thermal efficiency of the combined cycle power plant. The operating conditions investigated include gas turbine pressure ratio and gas turbine inlet temperature. The steam injection decreases the steam cycle output and boosts the gas cycle output and the net combined cycle work output and thermal efficiency significantly.

Genetic Optimization of Steam Injected Gas Turbine Power Plants

2002 ◽  
Author(s):  
Ibrahim Sinan Akmandor ◽  
O¨zhan O¨ksu¨z ◽  
Sec¸kin Go¨kaltun ◽  
Melih Han Bilgin
Keyword(s):  
Gas Turbine ◽  
Power Output ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Power Plants ◽  
Pressure Ratio ◽  
Steam Injection ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Compressor Pressure Ratio

A new methodology is developed to find the optimal steam injection levels in simple and combined cycle gas turbine power plants. When steam injection process is being applied to simple cycle gas turbines, it is shown to offer many benefits, including increased power output and efficiency as well as reduced exhaust emissions. For combined cycle power plants, steam injection in the gas turbine, significantly decreases the amount of flow and energy through the steam turbine and the overall power output of the combined cycle is decreased. This study focuses on finding the maximum power output and efficiency of steam injected simple and combined cycle gas turbines. For that purpose, the thermodynamic cycle analysis and a genetic algorithm are linked within an automated design loop. The multi-parameter objective function is either based on the power output or on the overall thermal efficiency. NOx levels have also been taken into account in a third objective function denoted as steam injection effectiveness. The calculations are done for a wide range of parameters such as compressor pressure ratio, turbine inlet temperature, air and steam mass flow rates. Firstly, 6 widely used simple and combined cycle power plants performance are used as test cases for thermodynamic cycle validation. Secondly, gas turbine main parameters are modified to yield the maximum generator power and thermal efficiency. Finally, the effects of uniform crossover, creep mutation, different random number seeds, population size and the number of children per pair of parents on the performance of the genetic algorithm are studied. Parametric analyses show that application of high turbine inlet temperature, high air mass flow rate and no steam injection lead to high power and high combined cycle thermal efficiency. On the contrary, when NOx reduction is desired, steam injection is necessary. For simple cycle, almost full amount of steam injection is required to increase power and efficiency as well as to reduce NOx. Moreover, it is found that the compressor pressure ratio for high power output is significantly lower than the compressor pressure ratio that drives the high thermal efficiency.

Impact of Inlet Fogging on the Performance of Steam Injected Cooled Gas Turbine Based Combined Cycle Power Plant

2017 ◽  
Author(s):  
Anoop Kumar Shukla ◽  
Onkar Singh
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Film Cooling ◽  
Pressure Ratio ◽  
Steam Injection ◽  
Combined Cycle ◽  
Specific Power ◽  
Temperature Cycle ◽  
Inlet Temperature ◽  
Combined Cycle Power Plant

Gas/steam combined cycle power plants are extensively used for power generation across the world. Today’s power plant operators are persistently requesting enhancement in performance. As a result, the rigour of thermodynamic design and optimization has grown tremendously. To enhance the gas turbine thermal efficiency and specific power output, the research and development work has centered on improving firing temperature, cycle pressure ratio, adopting improved component design, cooling and combustion technologies, and advanced materials and employing integrated system (e.g. combined cycles, intercooling, recuperation, reheat, chemical recuperation). In this paper a study is conducted for combining three systems namely inlet fogging, steam injection in combustor, and film cooling of gas turbine blade for performance enhancement of gas/steam combined cycle power plant. The evaluation of the integrated effect of inlet fogging, steam injection and film cooling on the gas turbine cycle performance is undertaken here. Study involves thermodynamic modeling of gas/steam combined cycle system based on the first law of thermodynamics. The results obtained based on modeling have been presented and analyzed through graphical depiction of variations in efficiency, specific work output, cycle pressure ratio, inlet air temperature & density variation, turbine inlet temperature, specific fuel consumption etc.

Proposal of Innovative Gas Turbine Combined Cycle Power Generation System

2004 ◽  
Author(s):  
Hideto Moritsuka
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Thermal Efficiency ◽  
Pressure Ratio ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Generation System ◽  
Turbine Inlet Temperature ◽  
Turbine Inlet ◽  
Power Generation System

In order to estimate the possibility to improve thermal efficiency of power generation use gas turbine combined cycle power generation system, benefits of employing the advanced gas turbine technologies proposed here have been made clear based on the recently developed 1500C-class steam cooling gas turbine and 1300C-class reheat cycle gas turbine combined cycle power generation systems. In addition, methane reforming cooling method and NO reducing catalytic reheater are proposed. Based on these findings, the Maximized efficiency Optimized Reheat cycle Innovative Gas Turbine Combined cycle (MORITC) Power Generation System with the most effective combination of advanced technologies and the new devices have been proposed. In case of the proposed reheat cycle gas turbine with pressure ratio being 55, the high pressure turbine inlet temperature being 1700C, the low pressure turbine inlet temperature being 800C, combined with the ultra super critical pressure, double reheat type heat recovery Rankine cycle, the thermal efficiency of combined cycle are expected approximately 66.7% (LHV, generator end).

Disappearing Thermo-Economic Sanity in Gas Turbine Combined Cycle Ratings: A Critique

2019 ◽  
Author(s):  
S. Can Gülen
Keyword(s):  
Gas Turbine ◽  
Thermal Efficiency ◽  
Film Cooling ◽  
Pressure Ratio ◽  
Open Loop ◽  
Product Line ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Turbine Inlet ◽  
Steam Turbine Condenser

Abstract There is very little doubt that there has been a noticeable advance in heavy-duty industrial gas turbine technology for utility scale electric power generation in the last decade. In keeping with the first six decades of the technology (roughly 1950 through 2010), the main drivers in increasing thermal efficiency and megawatt ratings have been increasing turbine inlet temperature and airflow. In accordance with the basic thermodynamic principles governing the underlying Brayton cycle, compressor pressure ratio kept pace with them. It is hard to quibble about the 40+ percent in rated thermal efficiency in simple cycle. If projected turbine inlet temperatures and cycle pressure ratios can be sustained in the field, current state-of-the-art in turbine hot gas path metallurgy, coatings and advanced film cooling techniques indeed support published ratings. Unfortunately, published combined cycle ratings are an altogether different matter. It is one thing to set the product line rating performance at an aggressive level with well-understood albeit optimistic assumptions such as very low water-cooled steam turbine condenser pressure with open-loop cooling. It is yet another thing to blatantly disregard fundamental laws of thermodynamics with outlandish performance ratings, which are unlikely to materialize even in the next decade or two cost-effectively (unless an unforeseen transformative step-change in technology materializes). In this paper, using fundamental thermodynamic arguments and detailed heat and mass balance simulations, it will be shown that some, if not all, OEM ratings are losing touch with reality.

Thermodynamic and Energy Study of a Regenerator in Gas Turbine Cycle and Optimization of Performances

2016 ◽  
Vol 5 (2) ◽  
pp. 25-44
Author(s):  
Saria Abed ◽  
Taher Khir ◽  
Ammar Ben Brahim
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Thermal Efficiency ◽  
Parametric Study ◽  
Pressure Ratio ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Compressor Pressure Ratio ◽  
Compressor Inlet ◽  
Gas Turbine Cycle

In this paper, thermodynamic study of simple and regenerative gas turbine cycles is exhibited. Firstly, thermodynamic models for both cycles are defined; thermal efficiencies of both cycles are determined, the overall heat transfer coefficient through the heat exchanger is calculated in order to determinate its performances and parametric study is carried out to investigate the effects of compressor inlet temperature, turbine inlet temperature and compressor pressure ratio on the parameters that measure cycles' performance. Subsequently, numerical optimization is established through EES software to determinate operating conditions. The results of parametric study have shown a significant impact of operating parameters on the performance of the cycle. According to this study, the regeneration technique improves the thermal efficiency by 10%. The studied regenerator has an important effectiveness (˜ 82%) which improves the heat transfer exchange; also a high compressor pressure ratio and an important combustion temperature can increase thermal efficiency.

Effect of Steam Injection in Gas Turbine Combustion Chamber on the Performance of a Natural Gas Fired Combined Cycle Power Generation Unit

2011 ◽  
Vol 110-116 ◽  
pp. 4574-4577
Author(s):  
Ibrahim Alaefour ◽  
Bale V. Reddy
Keyword(s):  
Power Generation ◽  
Natural Gas ◽  
Combustion Chamber ◽  
Gas Turbine ◽  
Steam Injection ◽  
Combined Cycle ◽  
First Law Of Thermodynamics ◽  
Power Generation Unit ◽  
Gas Turbine Combustion ◽  
Generation Unit

Combined cycle power generation plants are becoming popular to generate power at higher efficiencies with reduced greenhouse gas emissions. In the present work the effect of steam injection in the gas turbine combustion chamber on the performance of a natural gas fired combined cycle power plant is investigated. For a particular combined cycle power generation configuration, the effect of steam injection on the performance is conducted based on first law of thermodynamics. The steam injection influences the work output and efficiencies of gas turbine, steam turbine and combined cycle power generation unit.

Thermodynamics Analysis of a Combined Cycle Power Plant

2007 ◽  
Author(s):  
Feliciano Pava´n ◽  
Marco Romo ◽  
Juan Prince
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Pressure Ratio ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Work Output ◽  
Turbine Inlet Temperature ◽  
Combined Cycle Power Plant ◽  
Turbine Inlet ◽  
Combined Cycle Plant

The present paper is a thermodynamics analysis, i.e. both energy and exergy analyses for a natural gas based combined cycle power plant. The analysis was performed for an existing 240 MW plant, where the steam cycle reduces the irreversibilities during heat transfer from gas to water/steam. The effect of operating variables such as pressure ratio, gas turbine inlet temperature on the performance of combined cycle power plant has been investigated. The pressure ratio and maximum temperature (gas turbine inlet temperature) are identified as the dominant parameters having impact on the combined cycle plant performance. The work output of the topping cycle is found to increase with pressure ratio, while for the bottoming cycle it decreases. However, for the same gas turbine inlet temperature the overall work output of the combined cycle plant increases up to a certain pressure ratio, and thereafter not much increase is observed. The exergy losses of the individual components in the plant are evaluated based on second law of thermodynamics. The present results form a basis on which further work can be conducted to improve the performance of these units.

Enhancing Energy and Economic Performances of Combined Cycle Power Plants by Means of Gas-Cycle Regeneration

2014 ◽  
Author(s):  
Roberto Carapellucci ◽  
Lorena Giordano
Keyword(s):  
Gas Turbine ◽  
Power Plants ◽  
Waste Heat ◽  
Pressure Ratio ◽  
Unit Cost ◽  
Combined Cycle ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Efficiency Gain ◽  
Gas Power Plant

Efficiency improvement in the gas turbine sector has been mainly driven by increasing the turbine inlet temperature and compressor pressure ratio. For a fixed technology level, a further efficiency gain can be achieved through the utilization of waste thermal energy. Regeneration is an internal recovery technique that allows the reduction of heat input required at combustor, by preheating the air at compressor outlet. Under certain operating conditions, the temperature of exhaust gas leaving the regenerator is still enough high to allow the steam production via an heat recovery steam generator (HRSG). Regeneration in steam-gas power plants (CCGT) has the potential to enhance thermal efficiency, but reduces the margins for external recovery and then the bottoming steam cycle capacity. Moreover, the reduction of exhausts temperature at gas turbine outlet requires the reconsideration of HRSG operating parameters, in order to limit the increase of waste heat at the stack. The aim of this study is to explore the potential benefits that regeneration in the gas cycle gives on the whole steam-gas power plant. The extent of energy and economic performances improvement is evaluated, varying the gas turbine specifications and the layout and operating conditions of HRSG. Hence simple and regenerative configurations based on single and multi-pressure HRSG are compared, focusing on efficiency, specific CO2 emissions and unit cost of electricity (COE).

New Concept of a Micro Gas Turbine Based Co-Generation Package for Performance Improvement in Practical Use

2005 ◽  
Author(s):  
Kenichiro Mochizuki ◽  
Satoshi Shibata ◽  
Umeo Inoue ◽  
Toshiaki Tsuchiya ◽  
Hiroko Sotouchi ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Steam Generator ◽  
Thermal Efficiency ◽  
Heat Recovery ◽  
Steam Injection ◽  
Operating Conditions ◽  
Market Potential ◽  
Injection System ◽  
Heat Recovery Steam Generator ◽  
Micro Gas Turbine

As the energy consumption has been increasing rapidly in the commercial sector in Japan, the market potential for the micro gas turbine is significant and it will be realized substantially if the thermal efficiency is improved. One of measures is to introduce the steam injection system using the steam generated by the heat recovery steam generator. Steam injection tests have been carried out using a micro gas turbine (Capstone C60). Test results showed that key performance parameters such as power output, thermal efficiency and emissions were improved by the steam injection. The stable operation of micro gas turbine with steam injection was confirmed under various operating conditions. Consequently, a micro gas turbine based co-generation package with steam injection driven by a heat recovery steam generator (HRSG) with supplementary firing is proposed.

Effect of Deaerator Parameters on Simple and Reheat Gas/Steam Combined Cycle With Different Cooling Medium

2019 ◽  
Author(s):  
Mayank Maheshwari ◽  
Onkar Singh
Keyword(s):  
Gas Turbine ◽  
Mass Fraction ◽  
Power Plants ◽  
Performance Enhancement ◽  
Pressure Ratio ◽  
Combined Cycle ◽  
Cycle Performance ◽  
Inlet Temperature ◽  
Operating Pressure ◽  
Cooling Medium

Abstract Performance of gas/steam combined cycle power plants relies upon the performance exhibited by both gas based topping cycle and steam based bottoming cycle. Therefore, the measures for improving the performance of the gas turbine cycle and steam bottoming cycle eventually result in overall combined cycle performance enhancement. Gas turbine cooling medium affects the cooling efficacy. Amongst different parameters in the steam bottoming cycle, the deaerator parameter also plays its role in cycle performance. The present study analyzes the effect of deaerator’s operating pressure being varied from 1.6 bar to 2.2 bar in different configurations of simple and reheat gas/steam combined cycle with different cooling medium for fixed cycle pressure ratio of 40, turbine inlet temperature of 2000 K and ambient temperature of 303 K with varying ammonia mass fraction from 0.6 to 0.9. Analysis of the results obtained for different combined cycle configuration shows that for the simple gas turbine and reheat gas turbine-based configurations, the maximum work output of 643.78 kJ/kg of air and 730.87 kJ/kg of air respectively for ammonia mass fraction of 0.6, cycle efficiency of 54.55% and 53.14% respectively at ammonia mass fraction of 0.7 and second law efficiency of 59.71% and 57.95% respectively at ammonia mass fraction of 0.7 is obtained for the configuration having triple pressure HRVG with ammonia-water turbine at high pressure and intermediate pressure and steam turbine operating at deaerator pressure of 1.6 bar.

Sign in / Sign up

Export Citation Format

Share Document