Thermodynamics Analysis of a Combined Cycle Power Plant

2007 ◽  
Author(s):  
Feliciano Pava´n ◽  
Marco Romo ◽  
Juan Prince
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Pressure Ratio ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Work Output ◽  
Turbine Inlet Temperature ◽  
Combined Cycle Power Plant ◽  
Turbine Inlet ◽  
Combined Cycle Plant

The present paper is a thermodynamics analysis, i.e. both energy and exergy analyses for a natural gas based combined cycle power plant. The analysis was performed for an existing 240 MW plant, where the steam cycle reduces the irreversibilities during heat transfer from gas to water/steam. The effect of operating variables such as pressure ratio, gas turbine inlet temperature on the performance of combined cycle power plant has been investigated. The pressure ratio and maximum temperature (gas turbine inlet temperature) are identified as the dominant parameters having impact on the combined cycle plant performance. The work output of the topping cycle is found to increase with pressure ratio, while for the bottoming cycle it decreases. However, for the same gas turbine inlet temperature the overall work output of the combined cycle plant increases up to a certain pressure ratio, and thereafter not much increase is observed. The exergy losses of the individual components in the plant are evaluated based on second law of thermodynamics. The present results form a basis on which further work can be conducted to improve the performance of these units.

Impact of Inlet Fogging on the Performance of Steam Injected Cooled Gas Turbine Based Combined Cycle Power Plant

2017 ◽  
Author(s):  
Anoop Kumar Shukla ◽  
Onkar Singh
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Film Cooling ◽  
Pressure Ratio ◽  
Steam Injection ◽  
Combined Cycle ◽  
Specific Power ◽  
Temperature Cycle ◽  
Inlet Temperature ◽  
Combined Cycle Power Plant

Gas/steam combined cycle power plants are extensively used for power generation across the world. Today’s power plant operators are persistently requesting enhancement in performance. As a result, the rigour of thermodynamic design and optimization has grown tremendously. To enhance the gas turbine thermal efficiency and specific power output, the research and development work has centered on improving firing temperature, cycle pressure ratio, adopting improved component design, cooling and combustion technologies, and advanced materials and employing integrated system (e.g. combined cycles, intercooling, recuperation, reheat, chemical recuperation). In this paper a study is conducted for combining three systems namely inlet fogging, steam injection in combustor, and film cooling of gas turbine blade for performance enhancement of gas/steam combined cycle power plant. The evaluation of the integrated effect of inlet fogging, steam injection and film cooling on the gas turbine cycle performance is undertaken here. Study involves thermodynamic modeling of gas/steam combined cycle system based on the first law of thermodynamics. The results obtained based on modeling have been presented and analyzed through graphical depiction of variations in efficiency, specific work output, cycle pressure ratio, inlet air temperature & density variation, turbine inlet temperature, specific fuel consumption etc.

Proposal of Innovative Gas Turbine Combined Cycle Power Generation System

2004 ◽  
Author(s):  
Hideto Moritsuka
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Thermal Efficiency ◽  
Pressure Ratio ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Generation System ◽  
Turbine Inlet Temperature ◽  
Turbine Inlet ◽  
Power Generation System

In order to estimate the possibility to improve thermal efficiency of power generation use gas turbine combined cycle power generation system, benefits of employing the advanced gas turbine technologies proposed here have been made clear based on the recently developed 1500C-class steam cooling gas turbine and 1300C-class reheat cycle gas turbine combined cycle power generation systems. In addition, methane reforming cooling method and NO reducing catalytic reheater are proposed. Based on these findings, the Maximized efficiency Optimized Reheat cycle Innovative Gas Turbine Combined cycle (MORITC) Power Generation System with the most effective combination of advanced technologies and the new devices have been proposed. In case of the proposed reheat cycle gas turbine with pressure ratio being 55, the high pressure turbine inlet temperature being 1700C, the low pressure turbine inlet temperature being 800C, combined with the ultra super critical pressure, double reheat type heat recovery Rankine cycle, the thermal efficiency of combined cycle are expected approximately 66.7% (LHV, generator end).

scholarly journals Thermodynamical Optimization of a Combined Cycle Plant Performance

1994 ◽  
Author(s):  
K. Sarabchi ◽  
G. T. Polley
Keyword(s):  
Steam Turbine ◽  
Gas Turbine ◽  
Performance Optimization ◽  
Pressure Ratio ◽  
Combined Cycle ◽  
Plant Performance ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Turbine Inlet ◽  
Recovery Boiler

Computer modelling of Performance optimization was done to examine the effect of key operating variables like compressor pressure ratio, turbine inlet temperature, and recovery boiler pressure on performance parameters of a simple combined cycle and comparison was made to a simple gas turbine cycle. Both thermal efficiency and specific net work were examined as pressure ratio and recovery boiler pressure were varied for each turbine inlet temperature. Also careful consideration was given to admissible values of stack gas temperature, steam turbine outlet dryness fraction, and steam turbine outlet dryness fraction, and steam turbine inlet temperature. Specifically, it was shown that when we treat a combined cycle as an integrated system, efficiency optimization entails a pressure ratio below that suitable for simple gas turbine plant.

Performance Analysis of a Combined Cycle Power Plant Through Exergetic and Environmental Indices

2017 ◽  
Author(s):  
Edgar Vicente Torres González ◽  
Raúl Lugo Leyte ◽  
Martín Salazar Pereyra ◽  
Helen Denise Lugo Méndez ◽  
Miguel Toledo Velázquez ◽  
...  
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Environmental Indices ◽  
Combined Cycle Power Plant ◽  
Combustion Gases ◽  
Combined Cycle Plant ◽  
Exergetic Analysis ◽  
Gas Turbine Power Plant

In this paper is carried out a comparison between a gas turbine power plant and a combined cycle power plant through exergetic and environmental indices in order to determine performance and sustainability aspects of a gas turbine and combined cycle plant. First of all, an exergetic analysis of the gas turbine and the combined is carried out then the exergetic and environmental indices are calculated for the gas turbine (case A) and the combined cycle (case B). The exergetic indices are exergetic efficiency, waste exergy ratio, exergy destruction factor, recoverable exergy ratio, environmental effect factor and exergetic sustainability. Besides, the environmental indices are global warming, smog formation and acid rain indices. In the case A, the two gas turbines generate 278.4 MW; whereas 415.19 MW of electricity power is generated by the combined cycle (case B). The results show that exergetic sustainability index for cases A and B are 0.02888 and 0.1058 respectively. The steam turbine cycle improves the overall efficiency, as well as, the reviewed exergetic indexes. Besides, the environmental indices of the gas turbines (case A) are lower than the combined cycle environmental indices (case B), since the combustion gases are only generated in the combustion chamber.

scholarly journals High-Temperature Turbine Technology Readiness

1982 ◽  
Author(s):  
M. W. Horner ◽  
A. Caruvana
Keyword(s):  
High Temperature ◽  
Gas Turbine ◽  
Phase Ii ◽  
Combined Cycle ◽  
Technology Readiness ◽  
Inlet Temperature ◽  
Test Results ◽  
Turbine Inlet ◽  
Combined Cycle Plant ◽  
Gas Fuel

Final component and technology verification tests have been completed for application to a 2600°F rotor inlet temperature gas turbine. These tests have proven the capability of combustor, turbine hot section, and IGCC fuel systems and controls to operate in a combined cycle plant burning a coal-derived gas fuel at elevated gas turbine inlet temperatures (2600–3000°F). This paper presents recent test results and summarizes the overall progress made during the DOE-HTTT Phase II program.

Expanding Fuel Flexibility in MHPS’ Dry Low NOx Combustor

2018 ◽  
Author(s):  
Katsuyoshi Tada ◽  
Kei Inoue ◽  
Tomo Kawakami ◽  
Keijiro Saitoh ◽  
Satoshi Tanimura
Keyword(s):  
Power Systems ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Environmental Conservation ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Social Perspectives ◽  
Turbine Inlet ◽  
Fuel Flexibility

Gas-turbine combined-cycle (GTCC) power generation is clean and efficient, and its demand will increase in the future from economic and social perspectives. Raising turbine inlet temperature is an effective way to increase combined cycle efficiency and contributes to global environmental conservation by reducing CO2 emissions and preventing global warming. However, increasing turbine inlet temperature can lead to the increase of NOx emissions, depletion of the ozone layer and generation of photochemical smog. To deal with this issue, MHPS (MITSUBISHI HITACHI POWER SYSTEMS) and MHI (MITSUBISHI HEAVY INDUSTRIES) have developed Dry Low NOx (DLN) combustion techniques for high temperature gas turbines. In addition, fuel flexibility is one of the most important features for DLN combustors to meet the requirement of the gas turbine market. MHPS and MHI have demonstrated DLN combustor fuel flexibility with natural gas (NG) fuels that have a large Wobbe Index variation, a Hydrogen-NG mixture, and crude oils.

scholarly journals Study on effective parameter of the triple-pressure reheat combined cycle performance

2013 ◽  
Vol 17 (2) ◽  
pp. 497-508 ◽  
Author(s):  
Thamir Ibrahim ◽  
M.M. Rahman
Keyword(s):  
Power Plant ◽  
Ambient Temperature ◽  
Compression Ratio ◽  
Combined Cycle ◽  
Total Power ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Turbine Inlet ◽  
Overall Performance ◽  
Overall Efficiency

The thermodynamic analyses of the triple-pressure reheat combined cycle gas turbines with duct burner are presented and discussed in this paper. The overall performance of a combined cycle gas turbine power plant is influenced by the ambient temperature, compression ratio and turbine inlet temperature. These parameters affect the overall thermal efficiency, power output and the heat-rate. In this study a thermodynamic model was development on an existing actual combined cycle gas turbine (CCGT) (In this case study, an effort has been made to enhance the performance of the CCGT through a parametric study using a thermodynamic analysis. The effect of ambient temperature and operation parameter, including compression ratio and turbine inlet temperature, on the overall performance of CCGT are investigated. The code of the performance model for CCGT power plant was developed utilizing the THERMOFLEX software. The simulating results show that the total power output and overall efficiency of a CCGT decrease with increase the ambient temperature because increase the consumption power in the air compressor of a GT. The totals power of a CCGT decreases with increase the compression rate, while the overall efficiency of a CCGT increases with increase the compression ratio to 21, after that the overall efficiency will go down. Far there more the turbine inlet temperature increases the both total power and overall efficiency increase, so the turbine inlet temperature has a strong effect on the overall performance of CCGT power plant. Also the simulation model give a good result compared with MARAFIQ CCGT power plant. With these variables, the turbine inlet temperature causes the greatest overall performance variation.

scholarly journals Conceptual Design of a Pulverized Coal Furnace for a Utility Size Closed-Cycle, Gas-Turbine Power Plant

1979 ◽  
Author(s):  
H. J. Strumpf
Keyword(s):  
Heat Exchanger ◽  
Power Plant ◽  
Gas Turbine ◽  
Conceptual Design ◽  
Pulverized Coal ◽  
Temperature Cycle ◽  
Inlet Temperature ◽  
Closed Cycle ◽  
Turbine Inlet Temperature ◽  
Turbine Inlet

A study has recently been completed for the Department of Energy on the conceptual design of coal-fired, closed-cycle, gas-turbine power plants that operate at high turbine-inlet temperatures and use air as the cycle fluid. This paper describes the design of one type of heater system for such a power plant — a pulverized coal furnace. Designs are presented for a 1550 F (843 C) turbine inlet temperature cycle that utilizes metallic superalloy heat exchanger tubes and a 1750 F (954 C) turbine inlet temperature cycle that utilizes ceramic heat exchanger tubes. The heaters consist of two sections — a radiant section where heat is transferred primarily by radiation from the pulverized coal luminous flame, and a convective section where heat is transferred primarily by forced convection from the nonluminous combustion gas. To maintain flame stability in the furnace, a minimum power density criterion must be met. This requires modularization of the radiant heaters.

A 2000-HP Military Vehicle Gas Turbine: A Study of Significant Thermodynamic and Mechanical Parameters

1968 ◽  
Author(s):  
A. F. Carter
Keyword(s):  
Gas Turbine ◽  
Pressure Ratio ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Overall Design ◽  
Blade Cooling ◽  
Turbine Inlet ◽  
Military Vehicle ◽  
Compressor Pressure Ratio ◽  
Selection Of

During a study of possible gas turbine cycles for a 2000-hp unit for tank propulsion, it has been established that the level of achievable specific fuel consumption (sfc) is principally determined by the combustor inlet temperature. If a regenerative cycle is selected, a particular value of combustor inlet temperature (and hence sfc) can be produced by an extremely large number of combinations of compressor pressure ratio, turbine inlet temperature, and heat exchanger effectiveness. This paper outlines the overall design considerations which led to the selection of a relatively low pressure ratio engine in which the turbine inlet temperature was sufficiently low that blade cooling was not necessary.

Sign in / Sign up

Export Citation Format

Share Document