The Aerodynamic Characteristics of the Pantograph When the Train Passes Through the Tunnel

2017 ◽  
Author(s):  
Dilong Guo ◽  
Wen Liu ◽  
Junhao Song ◽  
Ye Zhang ◽  
Guowei Yang
Keyword(s):  
High Speed ◽  
Aerodynamic Force ◽  
Maximum Amplitude ◽  
Aerodynamic Characteristics ◽  
High Speed Train ◽  
Expansion Waves ◽  
Compression And Expansion ◽  
High Speed Trains ◽  
Current Characteristics ◽  
Pass Through

The aerodynamic force acting on the pantograph by the airflow is obviously unsteady and has a certain vibration frequency and amplitude, while the high-speed train passes through the tunnel. In addition to the unsteady behavior in the open-air operation, the compressive and expansion waves in the tunnel will be generated due to the influence of the blocking ratio. The propagation of the compression and expansion waves in the tunnel will affect the pantograph pressure distribution and cause the pantograph stress state to change significantly, which affects the current characteristics of the pantograph. In this paper, the aerodynamic force of the pantograph is studied with the method of the IDDES combined with overset grid technique when high speed train passes through the tunnel. The results show that the aerodynamic force of the pantograph is subjected to violent oscillations when the pantograph passes through the tunnel, especially at the entrance of the tunnel, the exit of the tunnel and the expansion wave passing through the pantograph. The changes of the pantograph aerodynamic force can reach a maximum amplitude of 106%. When high-speed trains pass through tunnels at different speeds, the aerodynamic coefficients of the pantographs are roughly the same.

Experimental Studies on Aerodynamic Characteristics of Pantograph System According to the Pantograph Cover Configurations for High Speed Train

2011 ◽  
Author(s):  
Yeongbin Lee ◽  
Minho Kwak ◽  
Kyu Hong Kim ◽  
Dong-Ho Lee
Keyword(s):  
Wind Tunnel ◽  
High Speed ◽  
Aerodynamic Drag ◽  
Aerodynamic Force ◽  
Experimental Studies ◽  
Wind Tunnel Test ◽  
Aerodynamic Characteristics ◽  
Experimental Models ◽  
High Speed Train ◽  
Drag And Lift

In this study, the aerodynamic characteristics of pantograph system according to the pantograph cover configurations for high speed train were investigated by wind tunnel test. Wind tunnel tests were conducted in the velocity range of 20∼70m/s with scaled experimental pantograph models. The experimental models were 1/4 scaled simplified pantograph system which consists of a double upper arm and a single lower arm with a square cylinder shaped panhead. The experimental model of the pantograph cover is also 1/4 scaled and were made as 4 different configurations. It is laid on the ground plate which modeled on the real roof shape of the Korean high speed train. Using a load cell, the aerodynamic force such as a lift and a drag which were acting on pantograph system were measured and the aerodynamic effects according to the various configurations of pantograph covers were investigated. In addition, the total pressure distributions of the wake regions behind the panhead of the pantograph system were measured to investigate the variations of flow pattern. From the experimental test results, we checked that the flow patterns and the aerodynamic characteristics around the pantograph systems are varied as the pantograph cover configurations. In addition, it is also found that pantograph cover induced to decrease the aerodynamic drag and lift forces. Finally, we proposed the aerodynamic improvement of pantograph cover and pantograph system for high speed train.

Comparative study on the use of acoustic emission and vibration analyses for the bearing fault diagnosis of high-speed trains

2021 ◽  
pp. 147592172110360
Author(s):  
Dongming Hou ◽  
Hongyuan Qi ◽  
Honglin Luo ◽  
Cuiping Wang ◽  
Jiangtian Yang
Keyword(s):  
Acoustic Emission ◽  
Fault Diagnosis ◽  
High Speed ◽  
High Speed Train ◽  
Signal Attenuation ◽  
Transmission Path ◽  
Bearing Fault Diagnosis ◽  
Operation Conditions ◽  
Fault Features ◽  
High Speed Trains

A wheel set bearing is an important supporting component of a high-speed train. Its quality and performance directly determine the overall safety of the train. Therefore, monitoring a wheel set bearing’s conditions for an early fault diagnosis is vital to ensure the safe operation of high-speed trains. However, the collected signals are often contaminated by environmental noise, transmission path, and signal attenuation because of the complexity of high-speed train systems and poor operation conditions, making it difficult to extract the early fault features of the wheel set bearing accurately. Vibration monitoring is most widely used for bearing fault diagnosis, with the acoustic emission (AE) technology emerging as a powerful tool. This article reports a comparison between vibration and AE technology in terms of their applicability for diagnosing naturally degraded wheel set bearings. In addition, a novel fault diagnosis method based on the optimized maximum second-order cyclostationarity blind deconvolution (CYCBD) and chirp Z-transform (CZT) is proposed to diagnose early composite fault defects in a wheel set bearing. The optimization CYCBD is adopted to enhance the fault-induced impact response and eliminate the interference of environmental noise, transmission path, and signal attenuation. CZT is used to improve the frequency resolution and match the fault features accurately under a limited data length condition. Moreover, the efficiency of the proposed method is verified by the simulated bearing signal and the real datasets. The results show that the proposed method is effective in the detection of wheel set bearing faults compared with the minimum entropy deconvolution (MED) and maximum correlated kurtosis deconvolution (MCKD) methods. This research is also the first to compare the effectiveness of applying AE and vibration technologies to diagnose a naturally degraded high-speed train bearing, particularly close to actual line operation conditions.

scholarly journals A Study on the Energy-Harvesting Device with a Magnetic Spring for Improved Durability in High-Speed Trains

Micromachines ◽  
2021 ◽  
Vol 12 (7) ◽  
pp. 830
Author(s):  
Jaehoon Kim
Keyword(s):  
Energy Harvesting ◽  
High Speed ◽  
Permanent Magnets ◽  
Critical Issue ◽  
Sensor Nodes ◽  
High Speed Train ◽  
Vibration Energy Harvesting ◽  
Magnetic Spring ◽  
High Speed Trains ◽  
Energy Harvesting Devices

Durability is a critical issue concerning energy-harvesting devices. Despite the energy-harvesting device’s excellent performance, moving components, such as the metal spring, can be damaged during operation. To solve the durability problem of the metal spring in a vibration-energy-harvesting (VEH) device, this study applied a non-contact magnetic spring to a VEH device using the repulsive force of permanent magnets. A laboratory experiment was conducted to determine the potential energy-harvesting power using the magnetic spring VEH device. In addition, the characteristics of the generated power were studied using the magnetic spring VEH device in a high-speed train traveling at 300 km/h. Through the high-speed train experiment, the power generated by both the metal spring VEH device and magnetic spring VEH device was measured, and the performance characteristics required for a power source for wireless sensor nodes in high-speed trains are discussed.

Aerodynamic Characteristics Analysis of High-Speed Train on Cutting under Crosswinds

2013 ◽  
Vol 300-301 ◽  
pp. 62-67
Author(s):  
Kun Ye ◽  
Ren Xian Li
Keyword(s):  
High Speed ◽  
Three Dimensional ◽  
Aerodynamic Characteristics ◽  
High Speed Train ◽  
Aerodynamic Forces ◽  
Cutting Depth ◽  
Cutting Slope ◽  
Characteristics Analysis ◽  
Relationship Of ◽  
The Relationship

Cutting is an effective device to reduce crosswind loads acting on trains. The cutting depth, width and gradient of slope are important factors for design and construction of cutting. Based on numerical analysis methods of three-dimensional viscous incompressible aerodynamics equations, aerodynamic side forces and yawing moments acting on the high-speed train, with different depths and widths of cutting，are calculated and analyzed under crosswinds，meanwhile the relationship of the gradient of cutting slope and transverse aerodynamic forces acting on trains are also studied. Simulation results show that aerodynamic side forces and yawing moments acting on the train（the first, middle and rear train）decrease with the increase of cutting depth. The relationship between transverse forces (moments) coefficients acting on the three sections and the cutting depth basically is the three cubed relation. The bigger is cutting width，the worse is running stability of train. The relationship between yawing moments coefficients acting each body of the train and the cutting width approximately is the three cubed relation. The transverse Aerodynamic forces decreased gradually with the increase of the gradient of cutting slope, the relationship between yawing moments coefficients acting each body of the train and the gradient of cutting slope basically is the four cubed relation.

A measurement method for the overturning coefficient of high-speed trains passing through complex terrain sections under strong wind conditions

2019 ◽  
Vol 234 (8) ◽  
pp. 885-895
Author(s):  
Zhaijun Lu ◽  
Weijia Huang ◽  
Mu Zhong ◽  
Dongrun Liu ◽  
Tian Li ◽  
...  
Keyword(s):  
Real Time ◽  
Complex Terrain ◽  
High Speed ◽  
Suspension System ◽  
Strong Wind ◽  
Real Time Monitoring ◽  
Monitoring Method ◽  
High Speed Trains ◽  
Strong Winds ◽  
Pass Through

Real-time monitoring of overturning coefficients is very important for ensuring the safety of high-speed trains passing through complex terrain sections under strong wind conditions. In recent years, the phenomenon of “car swaying” that occurs when trains pass through the complex terrain has brought new challenges to ensuring the safety and riding comfort of passengers. In China, more and more high-speed trains are facing strong wind environments when running in complex terrain sections. However, due to the limitation of objective conditions, so far, only a few economical and effective methods of measurement have been developed that are suitable for real-time monitoring of the overturning coefficient of commercial vehicles. Therefore, considering the applicability and universality of such a monitoring method, this study presents a method for measuring the overturning coefficient of trains using the primary suspension system under strong winds. A vehicle test was carried out to verify the accuracy of the method. The results show that after correction, the overturning coefficient obtained from the primary suspension system is generally consistent with the overturning coefficient obtained from the instrumented wheelset. The method of measuring the overturning coefficient of trains in strong wind environments with the primary suspension system is, thus, proven feasible.

scholarly journals Effect of High-Speed Train-Induced Wind on Trackside UAV Thrust Near Railway Bridge

2020 ◽  
Vol 10 (10) ◽  
pp. 3495 ◽  
Author(s):  
Hyuk-Jin Yoon ◽  
Su-Hwan Yun ◽  
Dae-Hyun Kim ◽  
Jae Hee Kim ◽  
Bong-Kwan Cho ◽  
...  
Keyword(s):  
Unmanned Aerial Vehicles ◽  
Wind Velocity ◽  
High Speed ◽  
Railway Bridge ◽  
High Speed Train ◽  
Box Girder ◽  
Railway Bridges ◽  
High Speed Trains ◽  
Thrust Measurement ◽  
Girder Bridge

Imaging devices attached to unmanned aerial vehicles (UAVs) are used for crack measurements of railway bridges constructed for high-speed trains. This research aims to investigate track-side wind induced by high-speed trains and its effect on UAV thrust near the railway bridge. Furthermore, the characteristics of train-induced wind in three axial directions along a track, wind velocity, and the effect of train-induced wind on the UAV thrust were analyzed. This was achieved by installing 3-axis ultrasonic anemometers and a UAV thrust measurement system on top of a PSC box girder bridge. The changes in the train-induced wind velocity were monitored along the train travel, width, and height directions. The train-induced wind was measured at distances of 0.8, 1.3, 2.3, and 2.8 m away from the train’s body to analyze wind velocity based on distance. It was found that the maximum wind velocity decreased linearly as the distance from the train’s body increased. The UAV thrust increased by up to 20% and 60%, owing to train-induced wind when the leading and trailing power cars of a high-speed train passed, respectively. Thus, it is necessary to conduct further research to develop robust control and a variable pitch-propeller that can control thrust.

Sign in / Sign up

Export Citation Format

Share Document