Parametric Study of Fluidic Oscillators for Use in Active Boundary Layer Control

2011 ◽  
Author(s):  
Marion Mack ◽  
Reinhard Niehuis ◽  
Andreas Fiala
Keyword(s):  
Boundary Layer ◽  
Parametric Study ◽  
Pressure Ratio ◽  
Pressure Fluctuations ◽  
Reynolds Numbers ◽  
Boundary Layer Transition ◽  
Layer Transition ◽  
Pressure Transducers ◽  
Tollmien Schlichting ◽  
Exit Mach Number

A parametric study was conducted to identify the main factors influencing the frequency produced by fluidic oscillators with the goal of using the actuator to trigger boundary layer transition through the excitation of Tollmien Schlichting waves. Test bench conditions were chosen to match the static pressure at the actuation position on the candidate blade profile for a cascade exit Mach number of 0.6 and Reynolds numbers from 60,000 to 200,000. The inlet vs. outlet pressure ratio and the position and geometry of the outlet holes were all varied. Additionally, the effect of the oscillator’s scale and the feedback channel geometry were considered. The flow at the exit was measured using a hot wire, while Kulite pressure transducers were used to measure pressure fluctuations within the device. This paper shows that fluidic oscillators can achieve frequencies of 10 kHz and that the parameters considered play an important role in the performance of these devices.

Effect of Reduced Frequency on the Boundary Layer of a Plunging Airfoil

2010 ◽  
Author(s):  
F. Rasi Marzabadi ◽  
M. R. Soltani ◽  
M. Masdari
Keyword(s):  
Boundary Layer ◽  
Separation Bubble ◽  
Reynolds Numbers ◽  
Boundary Layer Transition ◽  
Unsteady Boundary Layer ◽  
Layer Transition ◽  
Laminar Separation ◽  
Pressure Transducers ◽  
Reduced Frequency ◽  
Hot Film

This investigation addresses the boundary layer study of a plunging airfoil. It specifically concerns the effect of reduced frequency on transition and separation/reattachment of the unsteady boundary layer. The wind tunnel measurements were conducted using multiple hot-film sensors, pressure transducers and a boundary-layer rake, at Reynolds numbers of 0.42 to 0.84 million, and over reduced frequencies from 0.05 to 0.11. It was observed the boundary layer transition occurs by a laminar separation bubble. The unsteady laminar separation is promoted (delayed) by the increase of the reduced frequency in upstroke (downstroke) portion of the equivalent angle of attack.

Effects of Reynolds Number and Free-Stream Turbulence on Boundary Layer Transition in a Compressor Cascade

2000 ◽  
Author(s):  
Heinz-Adolf Schreiber ◽  
Wolfgang Steinert ◽  
Bernhard Küsters
Keyword(s):  
Boundary Layer ◽  
Free Stream ◽  
Reynolds Numbers ◽  
Boundary Layer Transition ◽  
Bypass Transition ◽  
Layer Transition ◽  
Free Stream Turbulence ◽  
High Reynolds Numbers ◽  
High Turbulence ◽  
High Reynolds

An experimental and analytical study has been performed on the effect of Reynolds number and free-stream turbulence on boundary layer transition location on the suction surface of a controlled diffusion airfoil (CDA). The experiments were conducted in a rectilinear cascade facility at Reynolds numbers between 0.7 and 3.0×106 and turbulence intensities from about 0.7 to 4%. An oil streak technique and liquid crystal coatings were used to visualize the boundary layer state. For small turbulence levels and all Reynolds numbers tested the accelerated front portion of the blade is laminar and transition occurs within a laminar separation bubble shortly after the maximum velocity near 35–40% of chord. For high turbulence levels (Tu > 3%) and high Reynolds numbers transition propagates upstream into the accelerated front portion of the CDA blade. For those conditions, the sensitivity to surface roughness increases considerably and at Tu = 4% bypass transition is observed near 7–10% of chord. Experimental results are compared to theoretical predictions using the transition model which is implemented in the MISES code of Youngren and Drela. Overall the results indicate that early bypass transition at high turbulence levels must alter the profile velocity distribution for compressor blades that are designed and optimized for high Reynolds numbers.

Velocity and Pressure Measurements Along a Row of Confined Cylinders

2006 ◽  
Author(s):  
Barton L. Smith ◽  
Jack J. Stepan ◽  
Donald M. McEligot
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Symmetry Plane ◽  
Field Measurements ◽  
Reynolds Numbers ◽  
Boundary Layer Transition ◽  
Recirculation Region ◽  
Pressure Measurements ◽  
Layer Transition ◽  
Flow Experiments

The results of flow experiments performed in a cylinder array designed to mimic a VHTR Nuclear Plant lower plenum design are presented. Pressure drop and velocity field measurements were made. Based on these measurements, five regimes of behavior are identified that are found to depend on Reynolds number. It is found that the recirculation region behind the cylinders is shorter than that of half cylinders placed on the wall representing the symmetry plane. Unlike a single cylinder, the separation point is found to always be on the rear of the cylinders, even at very low Reynolds number. Boundary layer transition is found to occur at much lower Reynolds numbers than previously reported.

Numerical simulation of boundary-layer transition and transition control

1989 ◽  
Vol 199 ◽  
pp. 403-440 ◽  
Author(s):  
E. Laurien ◽  
L. Kleiser
Keyword(s):  
Boundary Layer ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Transition Process ◽  
Numerical Results ◽  
Boundary Layer Transition ◽  
Two Dimensional ◽  
Layer Transition ◽  
Longitudinal Vortices ◽  
Tollmien Schlichting

The laminar-turbulent transition process in a parallel boundary-layer with Blasius profile is simulated by numerical integration of the three-dimensional incompressible Navier-Stokes equations using a spectral method. The model of spatially periodic disturbances developing in time is used. Both the classical Klebanoff-type and the subharmonic type of transition are simulated. Maps of the three-dimensional velocity and vorticity fields and visualizations by integrated fluid markers are obtained. The numerical results are compared with experimental measurements and flow visualizations by other authors. Good qualitative and quantitative agreement is found at corresponding stages of development up to the one-spike stage. After the appearance of two-dimensional Tollmien-Schlichting waves of sufficiently large amplitude an increasing three-dimensionality is observed. In particular, a peak-valley structure of the velocity fluctuations, mean longitudinal vortices and sharp spike-like instantaneous velocity signals are formed. The flow field is dominated by a three-dimensional horseshoe vortex system connected with free high-shear layers. Visualizations by time-lines show the formation of A-structures. Our numerical results connect various observations obtained with different experimental techniques. The initial three-dimensional steps of the transition process are consistent with the linear theory of secondary instability. In the later stages nonlinear interactions of the disturbance modes and the production of higher harmonics are essential.We also study the control of transition by local two-dimensional suction and blowing at the wall. It is shown that transition can be delayed or accelerated by superposing disturbances which are out of phase or in phase with oncoming Tollmien-Schlichting instability waves, respectively. Control is only effective if applied at an early, two-dimensional stage of transition. Mean longitudinal vortices remain even after successful control of the fluctuations.

Effects of Weak Free Stream Nonuniformity on Boundary Layer Transition (Keynote Paper)

2003 ◽  
Author(s):  
Jonathan H. Watmuff
Keyword(s):  
Boundary Layer ◽  
Free Stream ◽  
Leading Edge ◽  
Boundary Layer Transition ◽  
Mean Flow ◽  
Layer Transition ◽  
Free Stream Turbulence ◽  
Tollmien Schlichting ◽  
Distorted Waves ◽  
Thickness Variations

Experiments are described in which well-defined FSN (Free Stream Nonuniformity) distributions are introduced by placing fine wires upstream of the leading edge of a flat plate. Large amplitude spanwise thickness variations are present in the downstream boundary layer resulting from the interaction of the laminar wakes with the leading edge. Regions of elevated background unsteadiness appear on either side of the peak layer thickness, which share many of the characteristics of Klebanoff modes, observed at elevated Free Stream Turbulence (FST) levels. However, for the low background disturbance level of the free stream, the layer remains laminar to the end of the test section (Rx ≈ l.4×106) and there is no evidence of bursting or other phenomena associated with breakdown to turbulence. A vibrating ribbon apparatus is used to demonstrate that the deformation of the mean flow is responsible for substantial phase and amplitude distortion of Tollmien-Schlichting (TS) waves. Pseudo-flow visualization of hot-wire data shows that the breakdown of the distorted waves is more complex and occurs at a lower Reynolds number than the breakdown of the K-type secondary instability observed when the FSN is not present.

Boundary-Layer Control as a Means of Reducing Drag on Fully Submerged Bodies of Revolution

1985 ◽  
Vol 107 (3) ◽  
pp. 342-347 ◽  
Author(s):  
B. Bar-Haim ◽  
D. Weihs
Keyword(s):  
Boundary Layer ◽  
Reynolds Numbers ◽  
Boundary Layer Transition ◽  
Boundary Layer Control ◽  
Layer Transition ◽  
Bodies Of Revolution ◽  
Boundary Layer Suction ◽  
Technique Optimization ◽  
Axisymmetric Bodies ◽  
Layer Control

The drag of axisymmetric bodies can be reduced by boundary-layer suction, which delays transition and can control separation. In this study, boundary-layer transition is delayed by applying a distributed suction technique. Optimization calculations were performed to define the minimal drag bodies at Reynolds numbers of 107 and 108. The saving in drag relative to optimal bodies with non-controlled boundary layers is shown to be 18 and 78 percent, at Reynolds numbers of 107 and 108, respectively.

Experimental Investigation of Single Roughness Element Effects on Supersonic Boundary Layer Transition

2014 ◽  
Author(s):  
Henny Bottini ◽  
Bayindir H. Saracoglu ◽  
Guillermo Paniagua
Keyword(s):  
Boundary Layer ◽  
Wall Temperature ◽  
Roughness Element ◽  
Pressure Fluctuations ◽  
Supersonic Boundary Layer ◽  
Boundary Layer Transition ◽  
Adiabatic Wall ◽  
Layer Transition ◽  
Temperature And Pressure ◽  
Unsteady Effects

Predicting the characteristics of a transitional boundary layer remains an open challenge in supersonic flow fields. An experimental campaign to understand the effects of a single roughness element on a supersonic laminar boundary layer was designed. Two Mach numbers were tested, 1.6 and 2.3, including two roughness heights, 0.1 mm and 1 mm, over a flat plate. Steady and unsteady wall temperature and pressure levels were recorded to interpret the influence of the wake of the roughness. Heat flux and adiabatic wall temperature trends, temperature and pressure fluctuations RMS trends and time evolution of spectral content were reported. The initial wall temperature was varied during the wall temperature measurements and the resulting steady and unsteady effects on the roughness wake were investigated.

Effect of Tripping Laminar-to-Turbulent Boundary Layer Transition on Tip Vortex Cavitation

1997 ◽  
Vol 41 (01) ◽  
pp. 1-9
Author(s):  
T. Pichon ◽  
A. Pauchet ◽  
A. Astolfi ◽  
D. H. Fruman ◽  
J-Y. Billard
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Flat Plate ◽  
Cross Section ◽  
Lift Coefficient ◽  
Reynolds Numbers ◽  
Boundary Layer Transition ◽  
Tip Vortex ◽  
Layer Transition ◽  
Tip Vortex Cavitation

It is by now well established that, for Reynolds numbers larger than those corresponding to the conditions of laminar-to-turbulent boundary layer transition over a flat plate (≈0.5 × 106) and for a variety of wing shapes and cross sections, desinent cavitation numbers divided by the Reynolds number to the power 0.4 correlate with the square of the lift coefficient. In the case of foils having an NACA 16020 cross section and for Reynolds numbers below or close to those leading to transition over a flat plate, the results are very much different from those obtained for well-developed turbulent boundary layer conditions. Thus, a research program has been conducted in order to investigate the effect of boundary layer manipulation on cavitation occurrence. It consisted in determining the critical cavitation numbers, the lift coefficients, and the velocities in the tip vortex of foils having either a smooth surface or tripping roughness (promoters) near the leading edge. Tests were performed using elliptical foils of NACA 16020 cross section having the promoters extending over 60, 80 and 90 percent of the semi-span. The region near the tip was kept smooth in order to distinguish laminar-to-turbulent transition effects from tip vortex cavitation inhibition effects associated with artificial roughness at the wing tip. Results obtained at very low Reynolds numbers, ≥ 0.24 × 106, with the foil tripped on both the pressure and suction sides collapse rather well with those previously obtained at much larger Reynolds numbers with the smooth foil, and correlate with the square of the lift coefficient. The differences between the tripped and smooth foil results are due to the modification of the lift characteristics through the modification of the wing boundary layer, as shown by flow visualization studies, and as a result of the local tip vortex intensity.

Sign in / Sign up

Export Citation Format

Share Document