Experimental Studies of Leading Edge Contouring Influence on Secondary Losses in Transonic Turbines

2012 ◽  
Author(s):  
Ranjan Saha ◽  
Jens Fridh ◽  
Torsten Fransson ◽  
Boris I. Mamaev ◽  
Mats Annerfeldt
Keyword(s):  
Gas Turbine ◽  
Guide Vane ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Leading Edge ◽  
Secondary Flows ◽  
Noticeable Effect ◽  
Flow Angle ◽  
Wide Range ◽  
Contour Plots

An experimental study of the hub leading edge contouring using fillets is performed in an annular sector cascade to observe the influence of secondary flows and aerodynamic losses. The investigated vane is a three dimensional gas turbine guide vane (geometrically similar) with a mid-span aspect ratio of 0.46. The measurements are carried out on the leading edge fillet and baseline cases using pneumatic probes. Significant precautions have been taken to increase the accuracy of the measurements. The investigations are performed for a wide range of operating exit Mach numbers from 0.5 to 0.9 at a design inlet flow angle of 90°. Data presented include the loading, fields of total pressures, exit flow angles, radial flow angles, as well as profile and secondary losses. The vane has a small profile loss of approximately 2.5% and secondary loss of about 1.1%. Contour plots of vorticity distributions and velocity vectors indicate there is a small influence of the vortex-structure in endwall regions when the leading edge fillet is used. Compared to the baseline case the loss for the filleted case is lower up to 13% of span and higher from 13% to 20% of the span for a reference condition with Mach no. of 0.9. For the filleted case, there is a small increase of turning up to 15% of the span and then a small decrease up to 35% of the span. Hence, there are no significant influences on the losses and turning for the filleted case. Results lead to the conclusion that one cannot expect a noticeable effect of leading edge contouring on the aerodynamic efficiency for the investigated 1st stage vane of a modern gas turbine.

Influence of Pre-History and Leading Edge Contouring on Aero-Performance of a 3D Nozzle Guide Vane

2013 ◽  
Author(s):  
Ranjan Saha ◽  
Boris I. Mamaev ◽  
Jens Fridh ◽  
Björn Laumert ◽  
Torsten H. Fransson
Keyword(s):  
Guide Vane ◽  
Three Dimensional ◽  
Leading Edge ◽  
Stagnation Line ◽  
Wide Range ◽  
Nozzle Guide Vane ◽  
Turbine Vane ◽  
Loss Coefficients ◽  
Exit Mach Number ◽  
Nozzle Guide

Experiments are conducted to investigate the effect of the pre-history in the aerodynamic performance of a three-dimensional nozzle guide vane with a hub leading edge contouring. The performance is determined with two pneumatic probes (5 hole and 3 hole) concentrating mainly on the endwall. The investigated vane is a geometrically similar gas turbine vane for the first stage with a reference exit Mach number of 0.9. Results are compared for the baseline and filleted cases for a wide range of operating exit Mach numbers from 0.5 to 0.9. The presented data includes loading distributions, loss distributions, fields of exit flow angles, velocity vector and vorticity contour, as well as, mass-averaged loss coefficients. The results show an insignificant influence of the leading edge fillet on the performance of the vane. However, the pre-history (inlet condition) affects significantly in the secondary loss. Additionally, an oil visualization technique yields information about the streamlines on the solid vane surface which allows identifying the locations of secondary flow vortices, stagnation line and saddle point.

Influence of Prehistory and Leading Edge Contouring on Aero Performance of a Three-Dimensional Nozzle Guide Vane

2014 ◽  
Vol 136 (7) ◽  
Author(s):  
Ranjan Saha ◽  
Boris I. Mamaev ◽  
Jens Fridh ◽  
Björn Laumert ◽  
Torsten H. Fransson
Keyword(s):  
Guide Vane ◽  
Three Dimensional ◽  
Leading Edge ◽  
Stagnation Line ◽  
Wide Range ◽  
Nozzle Guide Vane ◽  
Loss Coefficients ◽  
Exit Mach Number ◽  
Nozzle Guide ◽  
End Wall

Experiments are conducted to investigate the effect of the prehistory in the aerodynamic performance of a three-dimensional nozzle guide vane with a hub leading edge contouring. The performance is determined with two pneumatic probes (five hole and three hole) concentrating mainly on the end wall. The investigated vane is a geometrically similar gas turbine vane for the first stage with a reference exit Mach number of 0.9. Results are compared for the baseline and filleted cases for a wide range of operating exit Mach numbers from 0.5 to 0.9. The presented data includes loading distributions, loss distributions, fields of exit flow angles, velocity vector, and vorticity contour, as well as mass-averaged loss coefficients. The results show an insignificant influence of the leading edge fillet on the performance of the vane. However, the prehistory (inlet condition) affects significantly in the secondary loss. Additionally, an oil visualization technique yields information about the streamlines on the solid vane surface, which allows identifying the locations of secondary flow vortices, stagnation line, and saddle point.

Aero-Thermal Aspects of Film Cooled Nozzle Guide Vane Endwalls: Part 1 — Aerodynamics

2020 ◽  
Author(s):  
Mahmood H. Alqefl ◽  
Kedar P. Nawathe ◽  
Pingting Chen ◽  
Rui Zhu ◽  
Yong W. Kim ◽  
...  
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Three Dimensional ◽  
Leading Edge ◽  
Secondary Flows ◽  
Protective Film ◽  
Cooling Flows ◽  
Nozzle Guide Vane ◽  
Nozzle Guide ◽  
Endwall Film Cooling

Abstract The first stage turbine of a modern gas turbine is subjected to high thermal loads which lead to a need for aggressive cooling schemes to protect its components from melting. Endwalls are particularly challenging to cool due to the complex system of secondary flows near them that wash the protective film coolants into the mainstream. This paper shows that without including combustor cooling, the complex secondary flow physics are not representative of modern engines. Aggressive injection of all cooling flows upstream of the passage is expected to interact and change passage aerodynamics and, subsequently, mixing and transport of coolants. This study describes, experimentally, the aero-thermal interaction of cooling flows near the endwall of a first stage nozzle guide vane passage. The test section involves an engine-representative combustor-turbine interface geometry, combustor coolant flow and endwall film cooling flow injected upstream of a linear cascade. The approach flow conditions represent flow exiting a cooled, low-NOx combustor. This first part of this two-part study aims to understand the complex aerodynamics near the endwall through detailed measurements of passage three-dimensional velocity fields with and without endwall film cooling. The aerodynamic measurements reveal a dominant vortex in the passage, named here as the Impingement Vortex, that opposes the passage vortex formed at the airfoil leading edge plane. This Impingement Vortex completely changes our description of flow over a modern film cooled endwall.

Aero-thermal Aspects of Film Cooled Nozzle Guide Vane Endwall - Part 1: Aerodynamics

2021 ◽  
pp. 1-54
Author(s):  
Mahmood H. Alqefl ◽  
Kedar P. Nawathe ◽  
Pingting Chen ◽  
Rui Zhu ◽  
Yong W. Kim ◽  
...  
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Three Dimensional ◽  
Leading Edge ◽  
Secondary Flows ◽  
Protective Film ◽  
Cooling Flows ◽  
Nozzle Guide Vane ◽  
Nozzle Guide ◽  
Endwall Film Cooling

Abstract The first stage turbine of a modern gas turbine is subjected to high thermal loads which lead to a need for aggressive cooling schemes to protect its components from melting. Endwalls are particularly challenging to cool due to the complex system of secondary flows near them that wash the protective film coolants into the mainstream. This paper shows that without including combustor cooling, the complex secondary flow physics are not representative of modern engines. Aggressive injection of all cooling flows upstream of the passage is expected to interact and change passage aerodynamics and, subsequently, mixing and transport of coolants. This study describes, experimentally, the aero-thermal interaction of cooling flows near the endwall of a first stage nozzle guide vane passage. The test section involves an engine-representative combustor-turbine interface geometry, combustor coolant flow and endwall film cooling flow injected upstream of a linear cascade. The approach flow conditions represent flow exiting a cooled, low-NOx combustor. This first part of this two-part study aims to understand the complex aerodynamics near the endwall through detailed measurements of passage three-dimensional velocity fields with and without endwall film cooling. The aerodynamic measurements reveal a dominant vortex in the passage, named here as the Impingement Vortex, that opposes the passage vortex formed at the airfoil leading edge plane. This Impingement Vortex completely changes our description of flow over a modern film cooled endwall.

Numerical Analysis on Effects of the Contoured Endwall on the Three Dimensional Flow Characteristics in an Annular Turbine Nozzle Vane

2007 ◽  
Author(s):  
Wu Sang Lee ◽  
Jin Taek Chung ◽  
Dae Hyun Kim ◽  
Seung Joo Choe
Keyword(s):  
Guide Vane ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Cross Flow ◽  
Leading Edge ◽  
Secondary Flows ◽  
Three Dimensional Flow ◽  
Dimensional Flow ◽  
Nozzle Guide Vane ◽  
Nozzle Guide

The three-dimensional flow in a turbine nozzle guide vane passage causes large secondary loss through the passage and increased heat transfer on the blade surface. In order to reduce or control these secondary flows, a linear turbine with contoured endwall configurations was used and changes in the three-dimensional flow field were analyzed and discussed. Contoured endwalls are installed at a location downstream of the saddle point near the leading edge of the pressure side blade and several positions along the centerline of the passage at constant distance. The objective of this study is to document the development of the three-dimensional flow in a turbine nozzle guide vane cascade with modified endwall. In addition, it proposes and appropriates endwall contouring which shows best overall loss reduction performance among the simulated contoured endwall. The results of this study show that the development of passage vortex and cross flow in the cascade composed of one flat and one contoured endwalls are affected by the acceleration which occurs in contoured endwall side. The overall loss is reduced near the flat endwall rather than contoured endwall, the best performance was shown for the case of 10–15% contoured for span-wise, 40–70% length of chord from trailing edge.

scholarly journals Influence of Swirl Clocking on the Performance of Turbine Stage with Three-Dimensional Nozzle Guide Vane

Energies ◽  
2021 ◽  
Vol 14 (17) ◽  
pp. 5503
Author(s):  
Shinyoung Jeon ◽  
Changmin Son ◽  
Jinuk Kim
Keyword(s):  
Guide Vane ◽  
Influencing Factor ◽  
Three Dimensional ◽  
Leading Edge ◽  
Aerodynamic Performance ◽  
Flow Angle ◽  
Nozzle Guide Vane ◽  
Nozzle Guide ◽  
Relationship Of ◽  
The Relationship

The effect of the swirl clocking on three-dimensional nozzle guide vane (NGV) is investigated using computational fluid dynamics. The research reports the loss characteristics of leaned and swept NGVs and the influence of swirl clocking. The three-dimensional NGVs are built by stacking the same 2D profile along different linear axes, characterized by different angles with respect to the normal or radial direction: ε = −12° ~ +12° for the leaned and γ = −5° ~ +10° for the swept airfoils. A total of 40 models are analyzed to study the effects of lean and sweep on aerodynamic performance. To investigate the influence of swirl clocking, the analysis cases include the center of the swirl that was positioned at the leading edge as well as the middle of the passage. The prediction results show that the relationship of the changes in mass flow rate and throat area are not monotonic. Further observation confirms the redistribution of loading and flow angle under different lean and sweep angles; thus, three-dimensional design is a key influencing factor on aerodynamic performance. In the presence of swirl clocking, NGV performance is changed significantly and the findings offer new insight and opportunities to improve three-dimensional NGV airfoil design.

scholarly journals Three-Dimensional Flow Predictions in Axial-Flow Turbine Cascades

1998 ◽  
Author(s):  
O. Niestroj ◽  
P. M. Came
Keyword(s):  
Experimental Studies ◽  
Three Dimensional ◽  
Axial Flow ◽  
Flow Angle ◽  
Contour Plots ◽  
Turbine Cascades ◽  
Flow Effects ◽  
Set Up ◽  
Annular Cascade ◽  
Good Agreement

Numerical investigations of the three-dimensional flowfields in a turbine linear cascade and in an annular, non-rotating turbine cascade have been carried out. Both cascades were the subjects of published experimental studies. In the experimental set-up for the annular cascade the hub wall upstream of the blades could be either stationary or rotating so that a collateral or a skewed inlet boundary layer could be achieved. The results of the computations have been compared with the experimental data. Total pressure loss coefficients and exit flow angles have been studied and in both cascades the predicted secondary flow effects are in good agreement with the experimental results. Two-dimensional contour plots in the measurement planes and pitchwise-averaged flow angle comparisons illustrate the accuracy of the computations.

Secondary Flows in a Transonic Cascade: Comparison Between Experimental and Numerical Results

1989 ◽  
Vol 111 (4) ◽  
pp. 369-377 ◽  
Author(s):  
F. Bassi ◽  
C. Osnaghi ◽  
A. Perdichizzi ◽  
M. Savini
Keyword(s):  
Experimental Data ◽  
Secondary Flow ◽  
Three Dimensional ◽  
Numerical Results ◽  
Secondary Flows ◽  
Streamwise Vorticity ◽  
Flow Angle ◽  
Flow Phenomena ◽  
Contour Plots ◽  
Flow Vortex

The paper presents a comparison between numerical results and experimental data about the secondary flow development in a linear transonic turbine cascade. Computations are carried out by using a three-dimensional inviscid Euler code, based on a Runge-Kutta explicit finite volume method. The experimental inlet total pressure distribution is imposed as inlet boundary condition to simulate the incoming endwall boundary layer. The comparison is made in four planes downstream of the cascade where detailed experimental data obtained in a transonic wind tunnel are available. For each of these planes secondary velocities and streamwise vorticity contour plots are presented and discussed. Moreover pitchwise mass averaged flow angle distributions showing overturning and underturning regions are shown. The comparison shows that an Euler code can predict the essential features of secondary flow phenomena like passage vortex location and intensity but a certain disagreement is found in the overturning and underturning angles evaluation. Numerical results also allow for the investigation of the development of secondary flows inside the blade channel. The investigation is carried out for three different Mach numbers: M2is = 0.5, 1.02, 1.38, in order to show the influence of compressibility on the flow vortex structure.

EFFECT OF AXIAL CASING GROOVE GEOMETRY ON ROTOR-GROOVE INTERACTIONS IN THE TIP REGION OF A COMPRESSOR

2021 ◽  
pp. 1-54
Author(s):  
Subhra Shankha Koley ◽  
Huang Chen ◽  
Ayush Saraswat ◽  
Joseph Katz
Keyword(s):  
Rotor Blade ◽  
Leading Edge ◽  
Secondary Flows ◽  
Low Flow ◽  
Flow Angle ◽  
Flow Rates ◽  
Piv Measurements ◽  
Tip Leakage ◽  
Large Vortex ◽  
Blade Leading Edge

Abstract This experimental study characterizes the interactions of axial casing grooves with the flow in the tip region of an axial turbomachine. The tests involve grooves with the same inlet overlapping with the rotor blade leading edge, but with different exit directions located upstream. Among them, U grooves, whose circumferential outflow opposes the blade motion, achieve a 60% reduction in stall flowrate, but degrade the efficiency around the best efficiency point (BEP) by 2%. The S grooves, whose outlets are parallel to the blade rotation, improve the stall flowrate by only 36%, but do not degrade the BEP performance. To elucidate the mechanisms involved, stereo-PIV measurements covering the tip region and interior of grooves are performed in a refractive index matched facility. At low flow rates, the inflow into both grooves, which peaks when they are aligned with the blade pressure side, rolls up into a large vortex that lingers within the groove. By design, the outflow from S grooves is circumferentially positive. For the U grooves, fast circumferentially negative outflow peaks at the base of each groove, causing substantial periodic variations in the flow angle near the blade leading edge. At BEP, interactions with both grooves become milder, and most of the tip leakage vortex remains in the passage. Interactions with the S grooves are limited hence they do not degrade the efficiency. In contrast, the inflow into and outflow from the U grooves reverses direction, causing entrainment of secondary flows, which likely contribute to the reduced BEP efficiency.

The Extension of a Solution-Adaptive Three-Dimensional Navier–Stokes Solver Toward Geometries of Arbitrary Complexity

1993 ◽  
Vol 115 (2) ◽  
pp. 283-295 ◽  
Author(s):  
W. N. Dawes
Keyword(s):  
Guide Vane ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Centrifugal Impeller ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Wide Range ◽  
Nozzle Guide Vane ◽  
Recent Developments ◽  
Nozzle Guide

This paper describes recent developments to a three-dimensional, unstructured mesh, solution-adaptive Navier–Stokes solver. By adopting a simple, pragmatic but systematic approach to mesh generation, the range of simulations that can be attempted is extended toward arbitrary geometries. The combined benefits of the approach result in a powerful analytical ability. Solutions for a wide range of flows are presented, including a transonic compressor rotor, a centrifugal impeller, a steam turbine nozzle guide vane with casing extraction belt, the internal coolant passage of a radial inflow turbine, and a turbine disk cavity flow.

Sign in / Sign up

Export Citation Format

Share Document