Rotating Instabilities Versus Rotating Stall in a High-Speed Centrifugal Compressor

2018 ◽  
Author(s):  
Julissa Grondin ◽  
Isabelle Trébinjac ◽  
Nicolas Rochuon
Keyword(s):  
Centrifugal Compressor ◽  
High Speed ◽  
Leading Edge ◽  
Propagation Speed ◽  
Rotating Stall ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Unsteady Rans ◽  
Measured Speed ◽  
The Subject

The subject of the paper is a high speed unshrouded centrifugal compressor in which rotating instabilities have been measured near the stage stall point. The impeller is studied numerically by means of unsteady RANS simulations, and the results are compared to experimental measurements. Instead of rotating instabilities, the numerical results directly capture a rotating stall pattern in which a tornado-like separation vortex is shed due to a separation at the impeller leading edge, and propagates around the circumference. The vortex has one end attached to the casing and the other end attached to the pressure side of the blade. Its propagation speed is within 10% from the measured speed of the rotating instabilities. Because of the high pressure gradient the tip leakage flow crosses the impeller front and thus convects the vortex in front of the adjacent blade. The spillage of the vortex in the adjacent channel convects radial and azimuthal vorticity onto the next blade. This triggers the inception of a new vortex, and induces the propagation of the rotating stall cells.

Structure of Diffuser Stall and Unsteady Vortices in a Centrifugal Compressor With Vaned Diffuser

2016 ◽  
Author(s):  
Nobumichi Fujisawa ◽  
Sota Ikezu ◽  
Yutaka Ohta
Keyword(s):  
Centrifugal Compressor ◽  
Leading Edge ◽  
Rotating Stall ◽  
Design Flow ◽  
Tip Leakage Flow ◽  
Vaned Diffuser ◽  
Tip Leakage ◽  
Close Proximity ◽  
Edge Vortex ◽  
Flow Blockage

The characteristics of a diffuser rotating stall and the evolution of a vortex generated on the diffuser leading edge (i.e., leading-edge vortex (LEV)) in a centrifugal compressor were investigated using experiments and numerical analyses. The experimental results showed that both impeller and diffuser rotating stalls occurred at 55 and 25 Hz during off-design flow operation. Both the stall cells existed only on the shroud side of the flow passages, which is in close proximity to the source location of the LEV. The numerical results showed that the LEV is a combination of a separated vortex near the leading edge and the extended tip-leakage flow from the impeller. In the partial flow operation, the LEV develops as the velocity decreases in the diffuser passages and forms a huge flow blockage within the diffuser passages. Therefore, the LEV may be considered to be one of the causes of diffuser stall in the centrifugal compressor.

scholarly journals Effects of Tip Leakage Flow on the Aerodynamic Performance and Stability of an Axial-Flow Transonic Compressor Stage

Energies ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4168
Author(s):  
Botao Zhang ◽  
Xiaochen Mao ◽  
Xiaoxiong Wu ◽  
Bo Liu
Keyword(s):  
Boundary Layer ◽  
Shock Wave ◽  
Axial Flow ◽  
Leading Edge ◽  
Rotating Stall ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Transonic Compressor

To explain the effect of tip leakage flow on the performance of an axial-flow transonic compressor, the compressors with different rotor tip clearances were studied numerically. The results show that as the rotor tip clearance increases, the leakage flow intensity is increased, the shock wave position is moved backward, and the interaction between the tip leakage vortex and shock wave is intensified, while that between the boundary layer and shock wave is weakened. Most of all, the stall mechanisms of the compressors with varying rotor tip clearances are different. The clearance leakage flow is the main cause of the rotating stall under large rotor tip clearance. However, the stall form for the compressor with half of the designed tip clearance is caused by the joint action of the rotor tip stall caused by the leakage flow spillage at the blade leading edge and the whole blade span stall caused by the separation of the boundary layer of the rotor and the stator passage. Within the investigated varied range, when the rotor tip clearance size is half of the design, the compressor performance is improved best, and the peak efficiency and stall margin are increased by 0.2% and 3.5%, respectively.

Tip Leakage Flow Instability in a Centrifugal Compressor

2021 ◽  
Vol 143 (4) ◽  
Author(s):  
Teng Cao ◽  
Tadashi Kanzaka ◽  
Liping Xu ◽  
Tobias Brandvik
Keyword(s):  
Shear Layer ◽  
Centrifugal Compressor ◽  
Large Scale ◽  
Flow Instability ◽  
Leading Edge ◽  
Main Stream ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Unstable Flow ◽  
Tip Leakage

Abstract In this paper, an unsteady tip leakage flow phenomenon is identified and investigated in a centrifugal compressor with a vaneless diffuser at near-stall conditions. This phenomenon is associated with the inception of a rotating instability in the compressor. The study is based on numerical simulations that are supported by experimental measurements. The study confirms that the unstable flow is governed by a Kelvin–Helmholtz type instability of the shear layer formed between the main-stream flow and the tip leakage flow. The shear layer instability induces large-scale vortex roll-up and forms vortex tubes, which propagate circumferentially, resulting in measured pressure fluctuations with short wavelength and high amplitude which rotate at about half of the blade speed. The 3D vortex tube is also found to interact with the main blade leading edge, causing the reduction of the blade loading identified in the experiment. The paper also reveals that the downstream volute imposes a once-per-rev circumferential nonuniform back pressure at the impeller exit, inducing circumferential loading variation at the impeller inducer, and causing circumferential variation in the unsteady tip leakage flow.

Stall Inception in a High Speed Centrifugal Compressor During Speed Transients

2017 ◽  
Author(s):  
Fangyuan Lou ◽  
John C. Fabian ◽  
Nicole L. Key
Keyword(s):  
Heat Transfer ◽  
Centrifugal Compressor ◽  
High Speed ◽  
Flow Instability ◽  
Leading Edge ◽  
Fast Response ◽  
Rotating Stall ◽  
Transient Performance ◽  
Stall Inception ◽  
Pressure Transducers

The inception and evolution of rotating stall in a high-speed centrifugal compressor are characterized during speed transients. Experiments were performed in the Single Stage Centrifugal Compressor (SSCC) facility at Purdue University and include speed transients from sub-idle to full speed at different throttle settings while collecting transient performance data. Results show a substantial difference in the compressor transient performance for accelerations versus decelerations. This difference is associated with the heat transfer between the flow and the hardware. The heat transfer from the hardware to the flow during the decelerations locates the compressor operating condition closer to the surge line and results in a significant reduction in surge margin during decelerations. Additionally, data were acquired from fast-response pressure transducers along the impeller shroud, in the vaneless space, and along the diffuser passages. Two different patterns of flow instabilities, including mild surge and short-length-scale rotating stall, are observed during the decelerations. The instability starts with a small pressure perturbation at the impeller leading edge and quickly develops into a single-lobe rotating stall burst. The stall cell propagates in the direction opposite of impeller rotation at approximately one third of the rotor speed. The rotating stall bursts are observed in both the impeller and diffuser, with the largest magnitudes near the diffuser throat. Furthermore, the flow instability develops into a continuous high frequency stall and remains in the fully developed stall condition.

scholarly journals Investigation on the Flow Field Entropy Structure of Non-Synchronous Blade Vibration in an Axial Turbocompressor

Entropy ◽  
2020 ◽  
Vol 22 (12) ◽  
pp. 1372
Author(s):  
Mingming Zhang ◽  
Anping Hou
Keyword(s):  
Flow Field ◽  
High Speed ◽  
Guide Vane ◽  
Leading Edge ◽  
Inlet Guide Vane ◽  
Tip Leakage Flow ◽  
Good Correspondence ◽  
Blade Vibration ◽  
Tip Leakage ◽  
Spiral Vortex

In order to explore the inducing factors and mechanism of the non-synchronous vibration, the flow field structure and its formation mechanism in the non-synchronous vibration state of a high speed turbocompressor are discussed in this paper, based on the fluid–structure interaction method. The predicted frequencies fBV (4.4EO), fAR (9.6EO) in the field have a good correspondence with the experimental data, which verify the reliability and accuracy of the numerical method. The results indicate that, under a deviation in the adjustment of inlet guide vane (IGV), the disturbances of pressure in the tip diffuse upstream and downstream, and maintain the corresponding relationship with the non-synchronous vibration frequency of the blade. An instability flow that developed at the tip region of 90% span emerged due to interactions among the incoming main flow, the axial separation backflow, and the tip leakage vortices. The separation vortices in the blade passage mixed up with the tip leakage flow reverse at the trailing edge of blade tip, presenting a spiral vortex structure which flows upstream to the leading edge of the adjacent blade. The disturbances of the spiral vortexes emerge to rotate at 54.5% of the rotor speed in the same rotating direction as a modal oscillation. The blade vibration in the turbocompressor is found to be related to the unsteadiness of the tip flow. The large pressure oscillation caused by the movement of the spiral vortex is regarded as the one of the main drivers for the non-synchronous vibration for the present turbocompressor, besides the deviation in the adjustment of IGV.

The Influence of Tip Clearance Momentum Flux on Stall Inception in a High-Speed Axial Compressor

2013 ◽  
Vol 135 (5) ◽  
Author(s):  
Joshua D. Cameron ◽  
Matthew A. Bennington ◽  
Mark H. Ross ◽  
Scott C. Morris ◽  
Juan Du ◽  
...  
Keyword(s):  
Momentum Flux ◽  
High Speed ◽  
Axial Compressor ◽  
Leading Edge ◽  
Tip Clearance ◽  
Flow Coefficient ◽  
Axial Position ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage

Experimental and numerical studies were conducted to investigate tip-leakage flow and its relationship to stall in a transonic axial compressor. The computational fluid dynamics (CFD) results were used to identify the existence of an interface between the approach flow and the tip-leakage flow. The experiments used a surface-streaking visualization method to identify the time-averaged location of this interface as a line of zero axial shear stress at the casing. The axial position of this line, denoted xzs, moved upstream with decreasing flow coefficient in both the experiments and computations. The line was consistently located at the rotor leading edge plane at the stalling flow coefficient, regardless of inflow boundary condition. These results were successfully modeled using a control volume approach that balanced the reverse axial momentum flux of the tip-leakage flow with the momentum flux of the approach fluid. Nonuniform tip clearance measurements demonstrated that movement of the interface upstream of the rotor leading edge plane leads to the generation of short length scale rotating disturbances. Therefore, stall was interpreted as a critical point in the momentum flux balance of the approach flow and the reverse axial momentum flux of the tip-leakage flow.

Nonaxisymmetric Study of Tip Leakage Flow in a Centrifugal Compressor With a Volute During Stall Process

2019 ◽  
Vol 141 (12) ◽  
Author(s):  
Ce Yang ◽  
Botai Su ◽  
Li Fu ◽  
Hang Zhang
Keyword(s):  
Centrifugal Compressor ◽  
Static Pressure ◽  
Leading Edge ◽  
Work Capacity ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
High Static Pressure ◽  
Circumferential Nonuniformity

Abstract Tip leakage flow (TLF) patterns, which affect compressor performance, are closely related to compressor stability. To date, minimal attention has been given to circumferential nonuniformity of the TLF in a centrifugal compressor with a nonaxisymmetric volute structure. In this study, the circumferential difference of the TLF in a centrifugal compressor with a volute during the stall process is analyzed. The circumferential nonuniformity of tip leakage vortex (TLV) trajectories, loading distribution near the tip, and distance between the TLV core and the leading edge (LE) of splitter blades were also investigated. It is shown that in the circumferential direction, there are two peaks associated with the angle (α) between the TLV trajectory of the seven main blades and the axial direction. As the stall process progresses, the blade whose LE is affected by the high static pressure band (PP) induced by the volute tongue (VT) loses its work capacity first and the α difference between this blade and the other blades increases. In addition, the tip loading and TLF velocity of the blade whose LE is affected by the high static pressure band induced by the VT are at a minimum, and the flow loss in the tip clearance is higher. There is a phenomenon of the TLV breakdown. When the blade trailing edge (TE) is located in the low static pressure region, TLV streamlines appear as a significant turn at the breakdown point. However, the TLV streamlines at other circumferential positions do not exhibit this phenomenon.

An Investigation of Stall Inception in Centrifugal Compressor Vaned Diffuser1

2012 ◽  
Vol 135 (1) ◽  
Author(s):  
Jonathan N. Everitt ◽  
Zoltán S. Spakovszky
Keyword(s):  
Centrifugal Compressor ◽  
Short Wavelength ◽  
Leading Edge ◽  
Rotating Stall ◽  
Full Scale ◽  
Vaned Diffuser ◽  
Stall Inception ◽  
Tip Leakage ◽  
Leakage Flows ◽  
Blade Tip

In compression systems, the stable operating range is limited by rotating stall and/or surge. Two distinct types of stall precursors can be observed prior to full scale instability: the development of long-wavelength modal waves or a short-wavelength, three-dimensional flow breakdown (so-called “spike” stall inception). The cause of the latter is not well understood; in axial machines it has been suggested that rotor blade-tip leakage flow plays an important role, but spikes have recently been observed in shrouded vaned diffusers of centrifugal compressors where these leakage flows are not present, suggesting an alternative mechanism may be at play. This paper investigates the onset of instability in a shrouded vaned diffuser from a highly loaded turbocharger centrifugal compressor and discusses the mechanisms thought to be responsible for the development of short-wavelength stall precursors. The approach combines unsteady 3D RANS simulations of an isolated vaned diffuser with previously obtained experimental results. The unsteady flow field simulation begins at the impeller exit radius, where flow is specified by a spanwise profile of flow angle and stagnation properties, derived from single-passage stage calculations but with flow pitchwise mixed. Through comparison with performance data from previous experiments and unsteady full-wheel simulations, it is shown that the diffuser is accurately matched to the impeller and the relevant flow features are well captured. Numerical forced response experiments are carried out to determine the diffuser dynamic behavior and point of instability onset. The unsteady simulations demonstrate the growth of short-wavelength precursors; the flow coefficient at which these occur, the rotation rate and circumferential extent agree with experimental measurements. Although the computational setup and domain limitations do not allow simulation of the fully developed spike nor full-scale instability, the model is sufficient to capture the onset of instability and allows the postulation of the following necessary conditions: (i) flow separation at the diffuser vane leading edge near the shroud endwall; (ii) radially reversed flow allowing vorticity shed from the leading edge to convect back into the vaneless space; and (iii) recirculation and accumulation of low stagnation pressure fluid in the vaneless space, increasing diffuser inlet blockage and leading to instability. Similarity exists with axial machines, where blade-tip leakage sets up endwall flow in the circumferential direction leading to flow breakdown and the inception of rotating stall. Rather than the tip leakage flows, the cause for circumferential endwall flow in the vaned diffuser is the combination of high swirl and the highly nonuniform spanwise flow profile at the impeller exit.

scholarly journals Discussion: “Criteria for Spike Initiated Rotating Stall” (Vo, H. D., Tan, C. S., Greitzer, E. M., 2008, ASME J. Turbomach., 130, p. 011023)

2008 ◽  
Vol 130 (1) ◽  
Author(s):  
A. Deppe ◽  
H. Saathoff ◽  
U. Stark
Keyword(s):  
Computational Study ◽  
Axial Flow ◽  
Leading Edge ◽  
Rotating Stall ◽  
Experimental Results ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Trailing Edge ◽  
Stall Inception ◽  
Tip Leakage

The paper “Criteria for Spike Initiated Rotating Stall” by Vo et al. (2008, ASME J. Turbomach., 130, p. 011023) provides a very important contribution to the understanding of spike-type stall inception in axial-flow compressors by demonstrating that spike-type disturbances are directly linked to the tip leakage flow of the rotor. The computational study of Vo et al. leads to the conclusion that two conditions have to be fulfilled simultaneously for the formation of spike-type stall: (i) axial backflow at the leading edge plane and (ii) axial backflow at the trailing edge plane. The objective of the present technical brief is to support these findings by corresponding experimental results.

Stall Inception in a High-Speed Centrifugal Compressor During Speed Transients

2017 ◽  
Vol 139 (12) ◽  
Author(s):  
Fangyuan Lou ◽  
John C. Fabian ◽  
Nicole L. Key
Keyword(s):  
Heat Transfer ◽  
Centrifugal Compressor ◽  
High Speed ◽  
Flow Instability ◽  
Leading Edge ◽  
Fast Response ◽  
Rotating Stall ◽  
Transient Performance ◽  
Stall Inception ◽  
Pressure Transducers

The inception and evolution of rotating stall in a high-speed centrifugal compressor are characterized during speed transients. Experiments were performed in the single stage centrifugal compressor (SSCC) facility at Purdue University and include speed transients from subidle to full speed at different throttle settings while collecting transient performance data. Results show a substantial difference in the compressor transient performance for accelerations versus decelerations. This difference is associated with the heat transfer between the flow and the hardware. The heat transfer from the hardware to the flow during the decelerations locates the compressor operating condition closer to the surge line and results in a significant reduction in surge margin during decelerations. Additionally, data were acquired from fast-response pressure transducers along the impeller shroud, in the vaneless space, and along the diffuser passages. Two different patterns of flow instabilities, including mild surge and short-length-scale rotating stall, are observed during the decelerations. The instability starts with a small pressure perturbation at the impeller leading edge (LE) and quickly develops into a single-lobe rotating stall burst. The stall cell propagates in the direction opposite of impeller rotation at approximately one-third of the rotor speed. The rotating stall bursts are observed in both the impeller and diffuser, with the largest magnitudes near the diffuser throat. Furthermore, the flow instability develops into a continuous high frequency stall and remains in the fully developed stall condition.

Sign in / Sign up

Export Citation Format

Share Document