Rotating Cooling Performance of Two-Pass Rectangular Channels With Cross Bridge and Oval-Shaped Dimple

2021 ◽  
Author(s):  
Qi Jing ◽  
Fahui Zhu ◽  
Zhufeng Liu ◽  
Yonghui Xie ◽  
Di Zhang
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Flow Structure ◽  
High Efficiency ◽  
Rectangular Channel ◽  
Coupling Mechanism ◽  
Internal Cooling ◽  
Cooling Performance ◽  
Cross Bridge ◽  
Bridge Type

Abstract In order to adapt to the high-efficiency and low-resistance performances required by the new generation of gas turbine, a new type of two-pass rectangular channel with cross bridge and oval-shaped dimple structure is proposed for internal cooling of blade mid chord region. Firstly, the flow structure, heat transfer and friction characteristics of the novel channels under stationary and rotating conditions are numerically analyzed and compared in detail. Then the effects of cross bridge type/layout and dimple dimension/arrangement on the cooling performance are discussed. And the coupling mechanism of cross bridge, turning bend, oval-shaped dimple and rotation effect is revealed. The results show that the introduction of the cross bridge enables the coolant flow into the second pass in a distributed manner, which weakens the flow aggregation and extrusion in the tip turning bend region, thus the flow structure is optimized. Although the heat transfer is slightly weakened, the friction factor is reduced by 66.3% and 51.4%, and the overall thermal performance is improved by 16.7% and 11.6% (different cases) at most, for stationary and rotating conditions, respectively. The oval-shaped dimple achieves local heat transfer enhancement by controlling flow separation and reattachment. Furthermore, the optimized cross bridge type/layout and dimple dimension/arrangement are also obtained. This research will provide important reference data for the development of high-efficiency mid chord cooling technology for gas turbine blade.

Detailed Velocity and Heat Transfer Measurements in an Advanced Gas Turbine Vane Insert Using MRV and IR Thermometry

2020 ◽  
Author(s):  
Michael J. Benson ◽  
David Bindon ◽  
Mattias Cooper ◽  
F. Todd Davidson ◽  
Benjamin Duhaime ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Gas Turbine ◽  
Computational Models ◽  
Internal Heat ◽  
Internal Cooling ◽  
Data Set ◽  
Ir Camera ◽  
Cooling Performance ◽  
Turbine Vane

Abstract This work reports the results of paired experiments for a complex internal cooling flow within a gas turbine vane using Magnetic Resonance Velocimetry (MRV) and steady-state Infrared (IR) thermometry. A scaled model of the leading edge insert for a gas turbine vane with multi-pass impingement was designed, built using stereolithography (SLA) fabrication methods, and tested using MRV techniques to collect a three-dimensional, three-component velocity field data set for a fully turbulent test case. Stagnation and recirculation zones were identified and assessed in terms of impact on potential cooling performance. A paired experiment employed an IR camera to measure the temperature profile data of a thin, heated stainless steel impingement surface modeling the inside turbine blade wall cooled by the impingement from the vane cooling insert, providing complementary data sets. The temperature data allow for the calculation of wall heat transfer characteristics, including the Nusselt number distribution for cooling performance analysis to inform design and validate computational models. Quantitative and qualitative comparisons of the paired results show that the flow velocity and cooling performance are highly coupled. Module-to-module variation in the surface Nusselt number distributions are evident, attributable to the complex interaction between transverse and impinging flows within the apparatus. Finally, a comparison with internal heat transfer correlations is conducted using the data from Florschuetz [1]. Measurement uncertainty was assessed and estimated to be approximately +7% for velocity and ranging from +3% to +10% for Nusselt number.

Influence of Coolant on Cooling Performance Sensitivity of Internally Convective Turbine Vane

2021 ◽  
Author(s):  
Thanapat Chotroongruang ◽  
Prasert Prapamonthon ◽  
Rungsimun Thongdee ◽  
Thanapat Thongmuenwaiyathon ◽  
Zhenxu Sun ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Film Cooling ◽  
Internal Cooling ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Turbine Engine ◽  
Performance Sensitivity ◽  
Turbine Vane ◽  
Cooling Air

Abstract Based on the Brayton cycle for gas-turbine engines, the high thermal efficiency and power output of a gas-turbine engine can be obtainable when the gas-turbine engine operates at high turbine inlet temperatures. However, turbine components e.g., inlet guide vane, rotor blade, and stator vane request high cooling performance. Typically, internal cooling and film cooling are two effective techniques that are widely used to protect high thermal loads for the turbine components in a state-of-the-art gas turbine. Consequently, the high thermal efficiency and power output can be obtained, and the turbine lifespan can be prolonged, also. On top of that, a comprehensive understanding of flow and heat transfer phenomena in the turbine components is very important. As a result, both experiments and simulations have been used to improve the cooling performance of the turbine components. In fact, the cooling air used in the internal cooling and film cooling is partially extracted from the compressor. Therefore, variations in the cooling air affect the cooling performance of the turbine components directly. This paper presents a numerical study on the influence of the cooling air on cooling-performance sensitivity of an internally convective turbine vane, MARK II using the computational fluid dynamics (CFD)/conjugate heat transfer (CHT) with the SST k-ω turbulence model. Result comparisons are conducted in terms of pressure, temperature, and cooling effectiveness under the effects of the inlet temperature, mass flow rate, turbulence intensity, and flow direction of the cooling air. The cooling-performance sensitivity to the coolant parameters is shown through variations of local cooling effectiveness, and area and volume-weighted average cooling effectiveness.

Detailed Velocity and Heat Transfer Measurements in an Advanced Gas Turbine Vane Insert Using MRV and IR Thermometry

2021 ◽  
pp. 1-11
Author(s):  
Michael J. Benson ◽  
David Bindon ◽  
Mattias Cooper ◽  
F. Todd Davidson ◽  
Benjamin Duhaime ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Gas Turbine ◽  
Computational Models ◽  
Internal Heat ◽  
Internal Cooling ◽  
Data Set ◽  
Ir Camera ◽  
Cooling Performance ◽  
Turbine Vane

Abstract This work reports the results of paired experiments for a complex internal cooling flow within a gas turbine vane using Magnetic Resonance Velocimetry (MRV) and steady-state Infrared (IR) thermometry. A scaled model of the leading edge insert for a gas turbine vane with multi-pass impingement was designed, built using stereolithography (SLA) fabrication methods, and tested using MRV techniques to collect a three-dimensional, three-component velocity field data set for a fully turbulent test case. Stagnation and recirculation zones were identified and assessed in terms of impact on potential cooling performance. A paired experiment employed an IR camera to measure the temperature profile data of a thin, heated stainless steel impingement surface modeling the inside turbine blade wall cooled by the impingement from the vane cooling insert, providing complementary data sets. The temperature data allow for the calculation of wall heat transfer characteristics, including the Nusselt number distribution for cooling performance analysis to inform design and validate computational models. Quantitative and qualitative comparisons of the paired results show that the flow velocity and cooling performance are highly coupled. Module-to-module variation in the surface Nusselt number distributions are evident, attributable to the complex interaction between transverse and impinging flows within the apparatus. Finally, a comparison with internal heat transfer correlations is conducted using the data from Florschuetz [1]. Measurement uncertainty was assessed and estimated to be approximately 7% for velocity and ranging from 3% to 10% for Nusselt number.

Experimental and Numerical Study on the Effects of the Relative Position of Film Hole and Orientation Ribs on the Film Cooling With Ribbed Cross-Flow Coolant Channel

2020 ◽  
Author(s):  
Bingran Li ◽  
Cunliang Liu ◽  
Lin Ye ◽  
Huiren Zhu ◽  
Fan Zhang
Keyword(s):  
Heat Transfer ◽  
Relative Position ◽  
Film Cooling ◽  
Numerical Study ◽  
Cross Flow ◽  
Internal Cooling ◽  
Transfer Coefficients ◽  
Cooling Performance ◽  
Heat Transfer Coefficients ◽  
Numerical Studies

Abstract To investigate the application of ribbed cross-flow coolant channels with film hole effusion and the effects of the internal cooling configuration on film cooling, experimental and numerical studies are conducted on the effect of the relative position of the film holes and different orientation ribs on the film cooling performance. Three cases of the relative position of the film holes and different orientation ribs (post-rib, centered, and pre-rib) in two ribbed cross-flow channels (135° and 45° orientation ribs) are investigated. The film cooling performances are measured under three blowing ratios by the transient liquid crystal measurement technique. A RANS simulation with the realizable k-ε turbulence model and enhanced wall treatment is performed. The results show that the cooling effectiveness and the downstream heat transfer coefficient for the 135° rib are basically the same in the three position cases, and the differences between the local effectiveness average values for the three are no more than 0.04. The differences between the heat transfer coefficients are no more than 0.1. The “pre-rib” and “centered” cases are studied for the 45° rib, and the position of the structures has little effect on the film cooling performance. In the different position cases, the outlet velocity distribution of the film holes, the jet pattern and the discharge coefficient are consistent with the variation in the cross flow. The related research previously published by the authors showed that the inclination of the ribs with respect to the holes affects the film cooling performance. This study reveals that the relative positions of the ribs and holes have little effect on the film cooling performance. This paper expands and improves the study of the effect of the internal cooling configuration on film cooling and makes a significant contribution to the design and industrial application of the internal cooling channel of a turbine blade.

Experimental Study on Flow Behavior and Heat Transfer Enhancement with Distinct Dimpled Gas Turbine Blade Internal Cooling Channel

2021 ◽  
pp. 1-28
Author(s):  
Farah Nazifa Nourin ◽  
Ryoichi S. Amano
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Heat Transfer Enhancement ◽  
Gas Turbine ◽  
Turbine Blade ◽  
Thermal Performance ◽  
Diameter Ratio ◽  
Internal Cooling ◽  
Cooling Channel ◽  
Transfer Enhancement

Abstract The study presents the investigation on heat transfer distribution along a gas turbine blade internal cooling channel. Six different cases were considered in this study, using the smooth surface channel as a baseline. Three different dimples depth-to-diameter ratios with 0.1, 0.25, and 0.50 were considered. Different combinations of partial spherical and leaf dimples were also studied with the Reynolds numbers of 6,000, 20,000, 30,000, 40,000, and 50,000. In addition to the experimental investigation, the numerical study was conducted using Large Eddy Simulation (LES) to validate the data. It was found that the highest depth-to-diameter ratio showed the highest heat transfer rate. However, there is a penalty for increased pressure drop. The highest pressure drop affects the overall thermal performance of the cooling channel. The results showed that the leaf dimpled surface is the best cooling channel based on the highest Reynolds number's heat transfer enhancement and friction factor. However, at the lowest Reynolds number, partial spherical dimples with a 0.25 depth to diameter ratio showed the highest thermal performance.

Computational Study of Gas Turbine Blade Cooling Channel

2010 ◽  
Author(s):  
R. S. Amano ◽  
Krishna Guntur ◽  
Jose Martinez Lucci
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Gas Turbine ◽  
Turbulence Models ◽  
Flow Patterns ◽  
Higher Order ◽  
Secondary Flows ◽  
Complex Flow ◽  
Cooling Performance ◽  
Cooling Channels

It has been a common practice to use cooling passages in gas turbine blade in order to keep the blade temperatures within the operating range. Insufficiently cooled blades are subject to oxidation, to cause creep rupture, and even to cause melting of the material. To design better cooling passages, better understanding of the flow patterns within the complicated flow channels is essential. The interactions between secondary flows and separation lead to very complex flow patterns. To accurately simulate these flows and heat transfer, both refined turbulence models and higher-order numerical schemes are indispensable for turbine designers to improve the cooling performance. Power output and the efficiency of turbine are completely related to gas firing temperature from chamber. The increment of gas firing temperature is limited by the blade material properties. Advancements in the cooling technology resulted in high firing temperatures with acceptable material temperatures. To better design the cooling channels and to improve the heat transfer, many researchers are studying the flow patterns inside the cooling channels both experimentally and computationally. In this paper, the authors present the performance of three turbulence models using TEACH software code in comparison with the experimental values. To test the performance, a square duct with rectangular ribs oriented at 90° and 45° degree and placed at regular intervals. The channel also has bleed holes. The normalized Nusselt number obtained from simulation are validated with that of experiment. The Reynolds number is set at 10,000 for both the simulation and experiment. The interactions between secondary flows and separation lead to very complex flow patterns. To accurately simulate these flows and heat transfer, both refined turbulence models and higher-order numerical schemes are indispensable for turbine designers to improve the cooling performance. The three-dimensional turbulent flows and heat transfer are numerically studied by using several different turbulence models, such as non-linear low-Reynolds number k-omega and Reynolds Stress (RSM) models. In k-omega model the cubic terms are included to represent the effects of extra strain-rates such as streamline curvature and three-dimensionality on both turbulence normal and shear stresses. The finite volume difference method incorporated with the higher-order bounded interpolation scheme has been employed in the present study. The outcome of this study will help determine the best suitable turbulence model for future studies.

scholarly journals Oscillator Fin as a Novel Heat Transfer Augmentation Device for Gas Turbine Cooling Applications

1998 ◽  
Author(s):  
Oguz Uzol ◽  
Cengiz Camci
Keyword(s):  
Heat Transfer ◽  
Kinetic Energy ◽  
Gas Turbine ◽  
Turbulent Kinetic Energy ◽  
Stokes Equations ◽  
Turbine Blades ◽  
Local Heat Transfer ◽  
Internal Cooling ◽  
Pin Fin ◽  
Heat Transfer Augmentation

A new concept for enhanced turbulent transport of heat in internal coolant passages of gas turbine blades is introduced. The new heat transfer augmentation component called “oscillator fin” is based on an unsteady flow system using the interaction of multiple unsteady jets and wakes generated downstream of a fluidic oscillator. Incompressible, unsteady and two dimensional solutions of Reynolds Averaged Navier-Stokes equations are obtained both for an oscillator fin and for an equivalent cylindrical pin fin and the results are compared. Preliminary results show that a significant increase in the turbulent kinetic energy level occur in the wake region of the oscillator fin with respect to the cylinder with similar level of aerodynamic penalty. The new concept does not require additional components or power to sustain its oscillations and its manufacturing is as easy as a conventional pin fin. The present study makes use of an unsteady numerical simulation of mass, momentum, turbulent kinetic energy and dissipation rate conservation equations for flow visualization downstream of the new oscillator fin and an equivalent cylinder. Relative enhancements of turbulent kinetic energy and comparisons of the total pressure field from transient simulations qualitatively suggest that the oscillator fin has excellent potential in enhancing local heat transfer in internal cooling passages without significant aerodynamic penalty.

scholarly journals CFD-BASED STUDY ON RELATIONSHIP BETWEEN COOLING PERFORMANCE OF PULSATING FLOW AND RIB HEIGHT MOUNTED IN MINI RECTANGULAR CHANNEL

2020 ◽  
Vol 1 (1) ◽  
pp. 26-29
Author(s):  
Shintaro Hayakawa ◽  
Takashi Fukue ◽  
Hidemi Shirakawa ◽  
Wakana Hiratsuka
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Performance ◽  
Rectangular Channel ◽  
The Body ◽  
Pulsating Flow ◽  
Cfd Analysis ◽  
Human Beings ◽  
Pumping Power ◽  
Transfer Enhancement ◽  
Cooling Performance

This study aims to develop a novel water-cooled device that increases heat transfer performance while inhibiting the increase of pumping power for next-generation electronic equipment. Our previous reports have reported that the combination of the pulsating flow, which is the unsteady flow that the supply flow rate is periodically changed likes a blood in the body of human beings, and the rib has higher cooling efficiency. In this report, in order to optimize the dimensions of the ribs from the viewpoint of the cooling performance, an investigation of the pulsating flow around the rib was conducted through 2D-CFD analysis while changing the height of the rib. It was found that the level of the heat transfer enhancement was dependent on the rib height.

Application of Conjugate Heat Transfer Analysis to Improvement of Cooled Turbine Vane and Blade for Industrial Gas Turbine

2018 ◽  
Author(s):  
Takeshi Horiuchi ◽  
Tomoki Taniguchi ◽  
Ryozo Tanaka ◽  
Masanori Ryu ◽  
Masahide Kazari
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Conjugate Heat Transfer ◽  
Metal Temperature ◽  
Heat Transfer Analysis ◽  
Estimation Accuracy ◽  
Cooling Performance ◽  
Measurement Results ◽  
Turbine Airfoils ◽  
Industrial Gas Turbine

In this paper, the Conjugate Heat Transfer (CHT) analysis, which utilizes commercial software STAR-CCM+ with detailed models and practical mesh size, was performed to the first stage cooled turbine airfoils for an industrial gas turbine produced by Kawasaki Heavy Industries, Ltd. (KHI). First its estimation accuracy was evaluated by comparing with the measurement results obtained with thermal index paint (TIP) and a pyrometer. After the validation of the CHT analysis, the metal temperature distribution was understood with the flow phenomena associated with it from the analysis results. To the parts where the metal temperature is locally high, then, the improvements of the cooling performance were considered with the CHT analysis and their effects were finally confirmed by measuring the metal temperature in the actual engine. The investigation reveals that the CHT analysis, which is validated with measurement results, makes it possible for cooling designers to efficiently improve the cooling performance of turbine airfoils with the adequate estimation accuracy, thus enhancing their durability for the reliability of gas turbines.

Heat Transfer in a Rotating Two-Pass Rectangular Channel Featuring a Converging Tip Turn With Various 45 deg Rib Coverage Designs

2019 ◽  
Vol 11 (6) ◽  
Author(s):  
Andrew F Chen ◽  
Chao-Cheng Shiau ◽  
Je-Chin Han ◽  
Robert Krewinkel
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Rectangular Channel ◽  
Copper Plate ◽  
Internal Cooling ◽  
Transfer Coefficients ◽  
First Passage ◽  
Pressure Loss Coefficient ◽  
Internal Surfaces ◽  
Turbine Airfoils

Varying aspect ratio (AR) channels are found in modern gas turbine airfoils for internal cooling purposes. Corresponding experimental data are needed in understanding and assisting the design of advanced cooling systems. The present study features a two-pass rectangular channel with an AR = 4:1 in the first pass with the radial outward flow and an AR = 2:1 in the second pass with the radial inward flow after a 180 deg tip turn. Effects of rib coverage near the tip region are investigated using profiled 45 deg ribs (P/e = 10, e/Dh ≈ 0.11, parallel and in-line) with three different configurations: less coverage, medium coverage, and full coverage. The Reynolds number (Re) ranges from 10,000 to 70,000 in the first passage. The highest rotation number achieved was Ro = 0.39 in the first passage and 0.16 in the second passage. Heat transfer coefficients on the internal surfaces were obtained by the regionally averaged copper plate method. The results showed that the rotation effects on both heat transfer and pressure loss coefficient are reduced with an increased rib coverage in the tip turn region. Different rib coverage upstream of the tip turn significantly changes the heat transfer in the turn portion. Heat transfer reduction (up to −27%) on the tip wall was seen at lower Ro. Dependence on the Reynolds number can be seen for this particular design. The combined geometric, rib coverage, and rotation effects should be taken into consideration in the internal cooling design.

Sign in / Sign up

Export Citation Format

Share Document