Heat Transport Characteristics of a Pulsating Heat Pipe

2007 ◽  
Author(s):  
Takao Nagasaki ◽  
Toshiyuki Hokazono ◽  
Yutaka Ito
Keyword(s):  
Heat Pipe ◽  
Heat Transport ◽  
Heat Load ◽  
Working Fluid ◽  
Pulsating Heat Pipe ◽  
Load Range ◽  
Large Heat ◽  
Inner Diameter ◽  
Bottom Heat ◽  
Better Than

Heat transport characteristics of a closed loop pulsating heat pipe (PHP) have been investigated experimentally. The heat pipe consists of 12 turn copper pipes with 2mm inner diameter. The lengths of heating, adiabatic and cooling sections are 53mm, 100mm and 51mm, respectively. The heat load was varied up to nearly 1000W for water and R141b as the working fluid. Three kinds of orientation, bottom heat vertical, horizontal, and top heat vertical, were tested. Detailed measurements of wall temperature fluctuations for water revealed several characteristic operating behaviors, such as intermittent oscillation and thermosyphon-like behavior. The performance of PHP with R141b is better than that with water in small heat load range due to its independence of orientation, conversely, PHP with water was more efficient than R141b in large heat load range. In order to improve the performance of PHP with R141b, diamond particles were added, resulting in better performance than water in the whole range of heat load.

Heat Transport Characteristics in Closed Loop Oscillating Heat Pipes

2005 ◽  
Author(s):  
Shuangfeng Wang ◽  
Shigefumi Nishio
Keyword(s):  
Heat Pipe ◽  
Heat Transport ◽  
Closed Loop ◽  
Flow Behavior ◽  
Working Fluid ◽  
Liquid Volume ◽  
High Heat Flux ◽  
Two Phase ◽  
Working Fluids ◽  
Inner Diameter

Heat transport rates of micro scale SEMOS (Self-Exciting Mode Oscillating) heat pipe with inner diameter of 1.5mm, 1.2mm and 0.9mm, were investigated by using R141b, ethanol and water as working fluids. The effects of inner diameter, liquid volume faction, and material properties of the working fluids are examined. It shows that the smaller the inner diameter, the higher the thermal transport density is. For removing high heat flux, the water is the most promising working fluid as it has the largest critical heat transfer rate and the widest operating range among the three kinds of working fluids. A one-dimensional numerical simulation is carried out to describe the heat transport characteristics and the two-phase flow behavior in the closed loop SEMOS heat pipe. The numerical prediction agrees with the experimental results fairly well, when the input heat through was not very high and the flow pattern was slug flow.   This paper was also originally published as part of the Proceedings of the ASME 2005 Pacific Rim Technical Conference and Exhibition on Integration and Packaging of MEMS, NEMS, and Electronic Systems.

Operating Activity Visualization and Thermal Performance Measurement of Pulsating Heat Pipe

2016 ◽  
Vol 369 ◽  
pp. 42-47 ◽  
Author(s):  
Patrik Nemec ◽  
Zuzana Kolková ◽  
Milan Malcho
Keyword(s):  
Heat Transfer ◽  
Performance Measurement ◽  
Heat Pipe ◽  
Thermal Performance ◽  
Vapour Phase ◽  
Working Fluid ◽  
Internal Diameter ◽  
Pulsating Heat Pipe ◽  
Inner Diameter ◽  
Thermo Physical Properties

Heat pipe is well known device which is used to heat transfer phase-change of working fluid. Pulsating heat pipe (PHP) is special type of heat pipe which heat transfer by pulsating movement of working fluid. Article deals about operating activity and thermal performance measurement of this special heat pipe. Operating activity visualization of PHP was performed with PHP made from glass. The two types of PHPs were made. The first PHP has internal diameter of tube 1 mm, second PHP has internal diameter of tube 1.5 mm and both PHPs have eleven meanders. The working fluids used in PHP were water and Fluorinert FC-72. These fluids were chose for their different thermo-physical properties and the visualization observe formation of liquid and vapour phase working fluid during filling process and working operation.Next, the article describes thermal performance measurement of PHP depending on working fluid amount and heat source temperature. Measurement was performed with PHP made from copper tube with inner diameter 1.5 mm curved to the twenty one meanders and filled with water. The results give us image about formation and distribution of working fluid in pulsating heat pipe and about influence of working fluid amount on the heat transfer ability of pulsating heat pipe.

scholarly journals Effect of Filling Ratio on Thermal Characteristics and Performance of a Pulsating Heat Pipe

2019 ◽  
Vol 9 (2) ◽  
pp. 3341-3345
Keyword(s):  
Heat Pipe ◽  
Thermal Characteristics ◽  
Filling Ratio ◽  
Working Fluid ◽  
Pulsating Heat Pipe ◽  
Key Factors ◽  
Condenser Section ◽  
Oscillating Heat Pipe ◽  
Bottom Heat ◽  
And Performance

Pulsating heat pipes are complex devices for heat transfer and their optimal thermal performance depends mainly on different parameters. This work is about the thermal efficiency of a closed-loop oscillating heat pipe with a diameter of 2.0 mm and 3.0 copper tube inner and outer. For all experiments, the filling ratio (FR) was used 40%, 50 %,70%,80% and heat inputs of 20W, 40W, 60W, and 80W was provided to PHP. The position of the PHP was vertical bottom heat type. The length of evaporator, adiabatic and condenser section was maintained 52 mm,170mm,60mm. Water and benzene were selected as working fluids. From the available literature it is observed that working fluid and filling ratio are key factors in PHP's performance. The results show that the thermal resistance decreases rapidly with the increase in the heat input to 20 to 40 W., while it decreases gradually over 40 to 80W.Simulation is done in CFD and experimental data were equated to the results.

Improvement of Heat Transfer Performance of Loop Heat Pipe for Electronic Devices

2011 ◽  
Author(s):  
Tomonao Takamatsu ◽  
Katsumi Hisano ◽  
Hideo Iwasaki
Keyword(s):  
Heat Pipe ◽  
Heat Transport ◽  
Thermal Energy ◽  
Heat Load ◽  
Cooling System ◽  
Electronic Devices ◽  
Working Fluid ◽  
Loop Heat Pipe ◽  
Reserve Area ◽  
Heat Transport Capability

In this paper is presented the results on performance of the cooling model using Loop Heat Pipe (LHP) system. In recent years, ever-ending demand of high performance CPU led to a rapid increase in the amount of heat dissipation. Consequently, thermal designing of electronic devices need to consider some suitable approach to achieve high cooling performance in limited space. Heat Pipe concept is expected to serve as an effective cooling system for laptop PC, however, it suffered from some problems as follows. The heat transport capability of conventional Heat Pipe decreases with the reduction in its diameter or increase in its length. Therefore, in order to use it as cooling system for future electronic devices, the above-mentioned limitations need to be removed. Because of the operating principle, the LHP system is capable of transferring larger amount of heat than conventional heat pipes. However, most of the LHP systems suffered from some problems like the necessity of installing check valves and reservoirs to avoid occurrence of counter flow. Therefore, we developed a simple LHP system to install it on electronic devices. Under the present experimental condition (the working fluid was water), by keeping the inside diameter of liquid and vapor line equal to 2mm, and the distance between evaporator and condenser equal to 200mm, it was possible to transport more than 85W of thermal energy. The thickness of evaporator was about 5mm although it included a structure to serve the purpose of controlling vapor flow direction inside it. Successful operation of this system at inclined position and its restart capability are confirmed experimentally. In order to make the internal water location visible, the present LHP system is reconstructed using transparent material. In addition, to estimate the limit of heat transport capability of the present LHP system using this thin evaporator, the air cooling system is replaced by liquid cooling one for condensing device. Then this transparent LHP system could transport more than 100W of thermal energy. However, the growth of bubbles in the reserve area with the increase in heat load observed experimentally led to an understanding that in order to achieve stable operation of the LHP system under high heat load condition, it is very much essential to keep enough water in the reserve area and avoid blocking the inlet with bubbles formation.

Visualization Experiment on the Start-up Performance of the Close Loop Pulsating Heat Pipe

2012 ◽  
Vol 550-553 ◽  
pp. 3150-3154 ◽  
Author(s):  
Xun Wang ◽  
Cheng Si Yang ◽  
Xin Xin Mao ◽  
Tong Han
Keyword(s):  
Heat Pipe ◽  
Heat Load ◽  
Early Stage ◽  
Flow Direction ◽  
High Heat ◽  
Working Fluid ◽  
Pulsating Heat Pipe ◽  
Optical Visualization ◽  
Start Up ◽  
Visualization Experiment

Through the visualization experiment, the behavior evolution of the vapor and liquid slugs in the pulsating heat pipe (PHP) was investigated in the start-up process. Optical visualization results indicate that the flow pattern mainly is slug flow in the start-up process. In the early stage of the start-up process, the distribution of vapor and liquid slugs was random at the beginning, and then gradually develops to the other form which can easily pulsate in the PHP. In the later stage, pulsation stagnation in short time and reversing of the flow direction of the working fluid could be found at low heat load, when there exists the circulation flow in the PHP. Circulation was formed along a certain direction at high heat load. In addition, the PHP can be started up with less time and lower minimum start load by using working fluid which has lower latent heat.

Visualization of Two-Phase Flow in 3D Printed Polycarbonate Pulsating Heat Pipe With Aluminum Substrate

2018 ◽  
Author(s):  
Takahiro Arai ◽  
Masahiro Kawaji ◽  
Yasushi Koito
Keyword(s):  
Heat Pipe ◽  
Heat Transport ◽  
Two Phase Flow ◽  
Aluminum Plate ◽  
Working Fluid ◽  
Phase Flow ◽  
Pulsating Heat Pipe ◽  
Two Phase ◽  
Flow Channels ◽  
Heat Transport Capability

A pulsating heat pipe (PHP) is a passive device with a good heat transport capability compared to other heat pipes. This paper describes an experimental investigation of a PHP with a serpentine channel fabricated by using a 3-D printer. The configuration of the flow channels in the PHP was close to that of commercially available PHPs made entirely of aluminum. To improve the heat transport capability and enable flow visualization, an aluminum plate was used on one side as the heat-transfer surface, on which transparent flow channels were fabricated by a 3-D printer and a polycarbonate filament. The interface between the aluminum plate and polycarbonate flow channel was cemented with a heat-resistant glue to ensure long term sealing. HFE-7000 was used as a working fluid. Oscillating two-phase flow in the PHP was observed with a high-speed digital video camera and transient surface temperatures at evaporator, insulator and condenser sections were measured by fine diameter thermocouples. The two-phase flow and thermal characteristics of the PHP at different heater power levels are presented.

scholarly journals Effect of Working Fluid on Thermal Performance of Closed Loop Pulsating Heat Pipe

2019 ◽  
Vol 9 (2) ◽  
pp. 953-956
Keyword(s):  
Thermal Resistance ◽  
Heat Pipe ◽  
Closed Loop ◽  
Filling Ratio ◽  
Working Fluid ◽  
External Diameter ◽  
Pulsating Heat Pipe ◽  
Condenser Section ◽  
Heat Transfer Efficiency ◽  
Bottom Heat

The pulsing heat pipe (PHP) is an technology that is increasingly capable of applying many manufacturing areas, but a thorough knowledge of its thermo-hydrodynamic There's far from enough system. This research explored the features of oscillation and the heat transfer efficiency of a closed-loop PHP using an internal and external diameter copper tube with 2.0 and 3.0 mm respectively. For all experimentation, filling ratio (FR) was 40%, five turns and different heat inputs of 20 to 80 W was supplied to PHP. The position of the PHP was vertical bottom heat type. 52 mm, 170 mm,60 mm was retained for the duration of the evaporator, adiabatic and condenser section. Water, Ethanol are chosen as working liquids. To understand, thermal resistance features and median evaporator pressures for multiple operating liquids at distinct heat inputs. An significant consideration for the results of PHPs is the research on PHP stated operating fluid. The result demonstrates that, with the rise of the heating output from 20 to 80 W, where as steadily increases above 80W, the thermal resistance reduces faster. By comparing Water , Ethanol working fluids, Ethanol provides the highest heat performance . The simulation is performed in Mat lab and the results have been contrasted

Orientation-Free Micro Heat Pipe

2005 ◽  
Author(s):  
Hisashi Sakurai ◽  
Yasuo Koizumi ◽  
Hiroyasu Ohtake
Keyword(s):  
Heat Pipe ◽  
Heat Transport ◽  
Flow Equation ◽  
Large Bubble ◽  
Working Fluid ◽  
Heating Spot ◽  
Micro Heat Pipe ◽  
Narrow Side ◽  
Flow Circuit ◽  
Better Than

A simple design micro-heat pipe was proposed. It was composed of a 20.0 × 20.0 mm square flow circuit which had two adjacent narrow-sides (1.0 × 1.0 mm2 or 0.5 × 1.0 mm2) and two adjacent wide-sides (5.0 × 1.0 mm2 or 2.5 × 1.0 mm2). A heating spot was at the narrow side and a cooling spot was at the wide side. Working fluid was ethanol. The flow circuit was placed horizontally. Bubbles generated at the heating spot migrated toward the wide side, the bubbles coalesced there to form a large bubble, and then the large bubble moved to the cooling spot. Finally, the large bubble was condensed at the cooling spot. This cycle repeated continuously. As a result of it, heat transport from the heating spot to the cooling spot was produced in the micro heat pipe even if it was arranged horizontally. It was confirmed that this simple device works as the heat pipe. An analysis of a flow mechanism was performed by solving a simple flow equation based on the flow resistance. It was proved that one-way circulation flow could be formed in the flow circuit. Predicted flow velocities were close to measured velocities. The heat transport performance of the proposed micro heat pipe was much better than the heat conduction of a stainless steel plate.

scholarly journals Experimental Investigation on the Thermal Performance of Pulsating Heat Pipe Heat Exchangers

Energies ◽  
2020 ◽  
Vol 13 (1) ◽  
pp. 269 ◽  
Author(s):  
Kai-Shing Yang ◽  
Ming-Yean Jiang ◽  
Chih-Yung Tseng ◽  
Shih-Kuo Wu ◽  
Jin-Cherng Shyu
Keyword(s):  
Heat Exchanger ◽  
Heat Pipe ◽  
Thermal Performance ◽  
Heat Exchangers ◽  
Filling Ratio ◽  
Working Fluid ◽  
Pulsating Heat Pipe ◽  
Evaporator Temperature ◽  
Inner Diameter ◽  
Air Streams

In this study, the vertically-oriented pulsating heat pipe (PHP) heat exchangers charged with either water or HFE-7000 in a filling ratio of 35% or 50% were fabricated to exchange the thermal energy between two air streams in a parallel-flow arrangement. Both the effectiveness of the heat exchangers and the thermal resistance of PHP with a size of 132 × 44 × 200 mm, at a specific evaporator temperature ranging from 55 to 100 °C and a specific airflow velocity ranging from 0.5 to 2.0 m/s were estimated. The results show that the heat pipe charged with HFE-7000 in either filling ratio is likely to function as an interconnected array of thermosiphon under all tested conditions because of the unfavorable tube inner diameter, whereas the water-charged PHP possibly creates the pulsating movement of the liquid and vapor slugs once the evaporator temperature is high enough, especially in a filling ratio of 50%. The degradation in the thermal performance of the HFE-7000-charged PHP heat exchanger resulted from the non-condensable gas in the tube became diminished as the evaporator temperature was increased. By examining the effectiveness of the present heat exchangers, it is suggested that water is a suitable working fluid while employing the PHP heat exchanger at an evaporator temperature higher than 70 °C. On the other hand, HFE-7000 is applicable to the PHP used at an evaporator temperature lower than 70 °C.

Heat Transport Characteristics of an Oscillating Heat Pipe With Al2O3 Nano-Fluid

2009 ◽  
Author(s):  
Shuangfeng Wang ◽  
Zirong Lin ◽  
Weibao Zhang ◽  
Jinjian Chen ◽  
Yong Tang
Keyword(s):  
Heat Pipe ◽  
Heat Transport ◽  
Pure Water ◽  
Working Fluid ◽  
External Diameter ◽  
Oscillating Heat Pipe ◽  
Nano Fluid ◽  
Heat Mode ◽  
Inclination Angles ◽  
Bottom Heat

Experimental investigation was conducted to exam the heat transport characteristics of an oscillating heat pipe (OHP) by using Al2O3 nano-fluid and pure water as working fluid. The test pipe consists of a copper tube with external diameter of 2.5 mm, inner diameter of 1.3 mm, and is welded into a four-turn oscillating heat pipe. The heat transport characteristics of the OHP have been studied under different liquid filling rates, different heat loads and different inclination angles (0° and 90°) when using water as working fluid. The results show that when heat load increases to a certain magnitude, the thermal resistance almost has little difference regardless of vertical bottom heat mode or horizontal heat mode. Comparing with pure water, Al2O3 nano-fluid as working fluid can enhance its heat-transport capability. When using vertical bottom heat mode and horizontal heat mode, the best concentration of Al2O3 nano-fluid is 0.5wt% and 0.1wt%, respectively.

Sign in / Sign up

Export Citation Format

Share Document