Experimental Investigation of HCCI Combustion With Reduced Compression Ratio and Narrow Include Angle Injector in a Small DI Diesel Engine

Author(s):  
Myung Yoon Kim ◽  
Ki Hyung Lee ◽  
Chang Sik Lee

An experimental investigation was performed on a small direct injection (DI) diesel engine equipped with a common-rail injection system to reduce exhaust emissions through HCCI (homogenous charge compression ignition) combustion. Recently, strict environmental standard requirements call for both lower fuel consumption and reduced emissions that could not be achieved by conventional diesel combustion. In this work experimental investigations to achieve simultaneous reduction of NOx and soot by combustion of more diluted fuel/air mixture before the start of ignition were carried out. To realize this fundamental concept, the experimental conditions including injection timing and EGR rate are varied with the different engine configurations. For reducing the deposition of early injected fuel, spray angle of injector is reduced to 60° and piston head shape also modified to fit with the new injector and to reduce the compression ratio to 15:1 for expanding the ignition delay to form diluted mixture before the ignition. Experimental results show that reduced spray angle with modified piston head allow very low NOx and soot emission level while maintaining the high IMEP of diesel combustion.

This paper represents the relative performance of a small single-cylinder diesel engine having capacity 3.5 kW. This paper covers experimental investigations of most influencing combustion parameters such as compression ratio, injection pressure and start of injection timing and their values on performance, emission and combustion characteristic of the small single-cylinder CRDI diesel engine for which the mechanical fuel injection system retrofitted with a simple version of the CRDI system. CRDI has yielded good results for large diesel and petrol engines but still not incorporate for cheaper small single-cylinder engines, typically used in the agricultural sector and decentralized power sector for a country like India. It is observed that starts of injection timing and injection pressure are the key parameters for improving the combustion characteristics and therefore engine performance while compression ratio mainly affects the emission characteristics of the engine. Retrofitted CRDI system yielded improved exhaust emission and performance of the engine.


2002 ◽  
Vol 124 (3) ◽  
pp. 660-667 ◽  
Author(s):  
K. Yamane ◽  
Y. Shimamoto

The objective of this study was to experimentally clarify the effect of two-stage split and early injection on the combustion and emission characteristics of a direct-injection (DI) diesel engine. Engine tests were carried out using a single-cylinder high-speed DI diesel engine and an injection system, combining an ordinary jerk pump and an electronically controlled high-pressure injection system, KD-3. In these experiments to compare the combustion and exhaust emission characteristics with two-stage split and early injection, a single-stage and early injection was tested. The FT-IR exhaust-gas analyzer simultaneously measured the exhaust emissions of 26 components. The results showed that HCHO, CH3CHO, and CH3COOH were emitted during the very early stage of both single injection and two-stage injection. These concentrations were higher than those from diesel combustion with ordinary fuel injection timings. These exhaust emissions are characteristic components of combustion by premixed compression ignition with extremely early injection. In particular, the HCHO concentration in exhaust was reduced with an increase in the maximum rate of heat release after cool flame due to pre-reaction of pre-mixture. At extremely early injection, the NOx concentration was extremely low; however, the indicated specific fuel consumption (ISFC) was higher than that of ordinary diesel combustion. In the case of two-stage injection, the degree of constant volume is increased, so that ISFC is improved. These results also demonstrated the possibility of reducing HCHO, NOx, and smoke emissions by means of two-stage split and early injection.


2019 ◽  
Vol 12 (3) ◽  
Author(s):  
Mohamed Al-Dawody ◽  
S.K. Bhatti

The aim of the present study is to analyse the combustion characteristics, performance and emission parameters of a variable compression ratio (VCR) diesel engine experimentally and numerically using soybean methyl ester (SME) biodiesel. Initially the engine is fed with diesel to capture the basic data, and then SME was tested as 20 % blend (B20), as 40% blend (B40) and as pure bio-fuel (B100). The experimental investigations are followed by a computational combustion and emissions analysis of diesel engine which is done by using the CFD software (ANSYS FLUENT 13). The combustion, performance and emissions parameters are evaluated by operating the engine at four different compression ratios of 15, 16, 17.5 and 19 and varying the load from 0 kW to 4.4 kW with 1.1 kW step. It is observed that peak pressure is closer to TDC when SME blends is increased. SME blend has earlier combustion start because of the advancement in the injection timing, shorter delay time. Increasing mixing ratio of biodiesel is found to decrease BTE slightly and increases the BSFC. Remarkable decrease in UHC and CO emissions as the ratio of SME is increased due to the complete combustion of biodiesel with presence of more oxygen in the combustion chamber. The measured BSN for B20, B40, and B100 SME was less than that of diesel fuel by 20.44%, 35.78%, and 48.3% respectively. It is inferred from the combustion analysis that as the compression ratio increases from 15 to 19 a decrease in smoke intensity, UHC, and CO, but it increases the emission of NOx. Both turbulent kinetic energy and turbulent dissipation rate were decreased as the percentage of SME increased by 10.84% and 2.01% respectively. The increase in compression ratio from 15 to 19 caused an increase in the peak pressure, density, combustion velocity, turbulence, peak temperature, NOx and a decrease in soot emissions. It can be assessed that the B20 SME is best suited to implement it into diesel engine without any effects. It has been founded from the results that 19 compression ratio has shown good performance and low emissions as compared to other compression ratios. The results obtained from the experimental investigation have been compared with the results of CFD analysis and are found to be in good agreement with each other with just slight deviation.


Sign in / Sign up

Export Citation Format

Share Document