Effect of Ambient Temperature and Humidity on Combustion and Emissions of a Spark Assisted Compression Ignition Engine

2015 ◽  
Author(s):  
Yan Chang ◽  
Brandon Mendrea ◽  
Jeff Sterniak ◽  
Stanislav V. Bohac
Keyword(s):  
Ambient Temperature ◽  
Flame Propagation ◽  
Pressure Rise ◽  
Ambient Air ◽  
Maximum Pressure ◽  
Compression Ignition ◽  
Pressure Rise Rate ◽  
Auto Ignition ◽  
Rise Rate ◽  
Temperature And Humidity

Spark Assisted Compression Ignition (SACI) offers more practical combustion phasing control and a softer pressure rise rate than Homogeneous Charge Compression Ignition (HCCI) combustion, and improved thermal efficiency and lower NOx emissions than Spark Ignition (SI) combustion. Any practical engine, including one that uses SACI in part of its operating range, must be robust to changes in ambient conditions. This study investigates the effects of ambient temperature and humidity on stoichiometric SACI engine performance, combustion and emissions. It is shown that at the medium speed and load SACI test point selected for this study, increasing ambient air temperature from 20°C to 41°C advances combustion phasing, increases maximum pressure rise rate, causes a larger fraction of the charge to be consumed by auto-ignition (and a smaller fraction by flame propagation), increases NOx, and increases Brake Specific Fuel Consumption (BSFC). Increasing ambient humidity from 32% to 60% retards combustion phasing, reduces maximum pressure rise rate, causes a larger fraction of the charge to be consumed by auto-ignition and a smaller fraction by flame propagation, increases Coefficient of Variation of IMEP (COV) of IMEP, reduces NOx, and increases BSFC. These results show that successful implementation of SACI combustion in real-world driving requires a control strategy that compensates for changes in ambient temperature and humidity.

scholarly journals Effect of Ambient Temperature and Humidity on Combustion and Emissions of a Spark-Assisted Compression Ignition Engine

2016 ◽  
Vol 139 (5) ◽  
Author(s):  
Yan Chang ◽  
Brandon Mendrea ◽  
Jeff Sterniak ◽  
Stanislav V. Bohac
Keyword(s):  
Ambient Temperature ◽  
Pressure Rise ◽  
Ambient Air ◽  
Maximum Pressure ◽  
Successful Implementation ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Pressure Rise Rate ◽  
Rise Rate ◽  
Temperature And Humidity

Spark-assisted compression ignition (SACI) offers more practical combustion phasing control and a lower pressure rise rate than homogeneous charge compression ignition (HCCI) combustion and improved thermal efficiency and lower NOx emissions than spark ignition (SI) combustion. Any practical passenger car engine, including one that uses SACI in part of its operating range, must be robust to changes in ambient conditions. This study investigates the effects of ambient temperature and humidity on stoichiometric SACI combustion and emissions. It is shown that at the medium speed and load SACI test point selected for this study, increasing ambient air temperature from 20 °C to 41 °C advances combustion phasing, increases maximum pressure rise rate, causes a larger fraction of the charge to be consumed by auto-ignition (and a smaller fraction by flame propagation), and increases NOx. Increasing ambient humidity from 32% to 60% retards combustion phasing, reduces maximum pressure rise rate, increases coefficient of variation (COV) of indicated mean effective pressure (IMEP), reduces NOx, and increases brake-specific fuel consumption (BSFC). These results show that successful implementation of SACI combustion in real-world driving requires a control strategy that compensates for changes in ambient temperature and humidity.

Potential of Fuel Stratification for Reducing Pressure Rise Rate in HCCI Engines Fueled With DME/n-Butane

2011 ◽  
Author(s):  
Ocktaeck Lim ◽  
Narankhuu Jamsran ◽  
Soojin Jeong ◽  
Youngduck Pyo ◽  
Kyuyeol Park
Keyword(s):  
Chemical Reaction ◽  
Pressure Rise ◽  
Reaction Model ◽  
Maximum Pressure ◽  
Mixture Ratio ◽  
Pressure Rise Rate ◽  
Fuel Stratification ◽  
Auto Ignition ◽  
Rise Rate ◽  
Hcci Engines

We investigated the efficacy of fuel stratification in a pre-mixture of di-methyl ether (DME) and n-Butane, which have different auto-ignition characteristics, for reducing the pressure rise rate (PRR) of homogeneous charge compression ignition (HCCI) engines. A new chemical reaction model was created by mixing DME and n-Butane and compared to existing chemical reaction models to verify the effects. The rate of maximum pressure rise depends on mixture ratio. When DME was charged with stratification and n-butane was charged with homogeneity, the maximum PRR was the lowest. The calculations were performed using the SENKIN application of CHEMKIN-II.

Characterization of Partially Premixed Combustion With Ethanol: EGR Sweeps, Low and Maximum Loads

2010 ◽  
Vol 132 (8) ◽  
Author(s):  
Vittorio Manente ◽  
Bengt Johansson ◽  
Pert Tunestal
Keyword(s):  
High Efficiency ◽  
Pressure Rise ◽  
Premixed Combustion ◽  
Maximum Pressure ◽  
Pressure Rise Rate ◽  
Start Of Injection ◽  
Partially Premixed Combustion ◽  
Rise Rate ◽  
Partially Premixed ◽  
Gas Recirculation

Exhaust gas recirculation (EGR) sweeps were performed on ethanol partially premixed combustion (PPC) to show different emission and efficiency trends as compared with diesel PPC. The sweeps showed that when the EGR rate is increased, the efficiency does not diminish, HC trace is flat, and CO is low even with 45% of EGR. NOx exponentially decreases by increasing EGR while soot levels are nearly zero throughout the sweep. The EGR sweeps underlined that at high EGR levels, the pressure rise rate is a concern. To overcome this problem and keep high efficiency and low emissions, a sweep in the timing of the pilot injection and pilot-main ratio was done at ∼16.5 bars gross IMEP. It was found that with a pilot-main ratio of 50:50, and by placing the pilot at −60 with 42% of EGR, NOx and soot are below EURO VI levels; the indicated efficiency is 47% and the maximum pressure rise rate is below 10 bar/CAD. Low load conditions were examined as well. It was found that by placing the start of injection at −35 top dead center, the efficiency is maximized, on the other hand, when the injection is at −25, the emissions are minimized, and the efficiency is only 1.64% lower than its optimum value. The idle test also showed that a certain amount of EGR is needed in order to minimize the pressure rise rate.

Performance of Dual Fuel Engine Running on Jojoba Oil as Pilot Fuel and CNG or LPG

2007 ◽  
Author(s):  
Mohamed Y. E. Selim ◽  
M. S. Radwan ◽  
H. E. Saleh
Keyword(s):  
Methyl Ester ◽  
Natural Gas ◽  
Pressure Rise ◽  
Combustion Noise ◽  
Dual Fuel ◽  
Maximum Pressure ◽  
Injection Timing ◽  
Pressure Rise Rate ◽  
Rise Rate ◽  
Pilot Fuel

The use of Jojoba Methyl Ester as a pilot fuel was investigated for almost the first time as a way to improve the performance of dual fuel engine running on natural gas or LPG at part load. The dual fuel engine used was Ricardo E6 variable compression diesel engine and it used either compressed natural gas (CNG) or liquefied petroleum gas (LPG) as the main fuel and Jojoba Methyl Ester as a pilot fuel. Diesel fuel was used as a reference fuel for the dual fuel engine results. During the experimental tests, the following have been measured: engine efficiency in terms of specific fuel consumption, brake power output, combustion noise in terms of maximum pressure rise rate and maximum pressure, exhaust emissions in terms of carbon monoxide and hydrocarbons, knocking limits in terms of maximum torque at onset of knocking, and cyclic data of 100 engine cycle in terms of maximum pressure and its pressure rise rate. The tests examined the following engine parameters: gaseous fuel type, engine speed and load, pilot fuel injection timing, pilot fuel mass and compression ratio. Results showed that using the Jojoba fuel with its improved properties has improved the dual fuel engine performance, reduced the combustion noise, extended knocking limits and reduced the cyclic variability of the combustion.

Characterization of Partially Premixed Combustion With Ethanol: EGR Sweeps, Low and Maximum Loads

2009 ◽  
Author(s):  
Vittorio Manente ◽  
Bengt Johansson ◽  
Pert Tunestal
Keyword(s):  
High Efficiency ◽  
Pressure Rise ◽  
Premixed Combustion ◽  
Maximum Pressure ◽  
Pressure Rise Rate ◽  
Partially Premixed Combustion ◽  
Rise Rate ◽  
Low Load ◽  
Partially Premixed

EGR sweeps were performed on Ethanol Partially Premixed Combustion, PPC, to show different emission and efficiency trends as compared to Diesel PPC. The sweeps showed that increasing the EGR rate the efficiency does not diminish, HC trace is flat and CO is low even with 45% of EGR. NOx exponentially decreases by increasing EGR while soot levels are nearly zero throughout the sweep. The EGR sweeps underlined that at high EGR levels, the pressure rise rate is a concern. To overcome this problem and keep high efficiency and low emissions a sweep in timing of the pilot injection and pilot-main ratio was done at ∼16.5 bar gross IMEP. It was found that with a pilot-main ratio of 50–50 and by placing the pilot at −60 with 42% of EGR, NOx and soot are below EURO VI levels, the indicated efficiency is 47% and the maximum pressure rise rate is below 10 bar/CAD. Low load conditions were examined as well. It was found that by placing the SOI at −35 TDC the efficiency is maximized on the other hand when the injection is at −25 the emissions are minimized and the efficiency is only 1.64% lower than its optimum value. The idle test also showed that a certain amount of EGR is needed in order to minimize the pressure rise rate.

Post Injection Strategy for the Reduction of the Peak Pressure Rise Rate of Neat N-Butanol Combustion

2015 ◽  
Author(s):  
Marko Jeftić ◽  
Ming Zheng
Keyword(s):  
Peak Pressure ◽  
Pressure Rise ◽  
Injection Timing ◽  
Post Injection ◽  
Compression Ignition ◽  
Cylinder Pressure ◽  
Compression Ignition Engine ◽  
Pressure Rise Rate ◽  
Injection Duration ◽  
Rise Rate

Enhanced premixed combustion of neat butanol in a compression ignition engine can have challenges with regards to the peak pressure rise rate and the peak in-cylinder pressure. It was proposed to utilize a butanol post injection to reduce the peak pressure rise rate and the peak in-cylinder pressure while maintaining a constant engine load. Post injection timing and duration sweeps were carried out with neat n-butanol in a compression ignition engine. The post injection timing sweep results indicated that the use of an early butanol post injection reduced the peak pressure rise rate and the peak in-cylinder pressure and it was observed that there was an optimal post injection timing range for the maximum reduction of these parameters. The results also showed that an early post injection of butanol increased the nitrogen oxide emissions and an FTIR analysis revealed that late post injections increased the emissions of unburned butanol. The post injection duration sweep indicated that the peak pressure rise rate was significantly reduced by increasing the post injection duration at constant load conditions. There was also a reduction in the peak in-cylinder pressure. Measurements with a hydrogen mass spectrometer showed that there was an increased presence of hydrogen in the exhaust gas when the post injection duration was increased but the total yield of hydrogen was relatively low. It was observed that the coefficient of variation for the indicated mean effective pressure was significantly increased and that the indicated thermal efficiency was reduced when the post injection duration was increased. The results also showed that there were increased nitrogen oxide, carbon monoxide, and total hydrocarbon emissions for larger post injections. Although the use of a post injection resulted in emission and thermal efficiency penalties at medium load conditions, the results demonstrated that the post injection strategy successfully reduced the peak pressure rise rate and this characteristic can be potentially useful for higher load applications where the peak pressure rise rate is of greater concern.

Combustion parameter evaluation of diesel engine via vibration acceleration signal

2021 ◽  
pp. 146808742110308
Author(s):  
Pan Zhang ◽  
Wenzhi Gao ◽  
Yong Li ◽  
Zhaoyi Wei
Keyword(s):  
Peak Pressure ◽  
Pressure Rise ◽  
Peak Position ◽  
Maximum Pressure ◽  
Cylinder Pressure ◽  
Combustion Control ◽  
Pressure Rise Rate ◽  
Acceleration Signal ◽  
Rise Rate ◽  
Start Of Combustion

Efficient combustion control has increasingly become a quality requirement for automobile manufacturers because of its impact on pollutant and greenhouse gas emissions. In view of this, the management system development of modern internal combustion engines is mainly aimed at combustion control. The real-time detection of in-cylinder pressure characteristic parameters has a considerable significance on the closed-loop combustion control of the internal combustion engine. This paper presents a detection method in which the start of combustion, peak pressure, maximum pressure rise rate, and phase of maximum pressure rise rate are identified through vibration acceleration signal. In order to analyze the relationship between vibration and in-cylinder pressure signal, experimental data are acquired in a diesel engine by implementing various injection strategies and engine operating conditions (speed and load). The results show that the start of combustion can be detected by analyzing its relationship with the peak position of the filtered vibration signal, and the phase of the maximum pressure rise rate can be identified by examining its relationship with the zero-cross position that is adjacent to the right of the peak position. Moreover, the filtered vibration signals are also truncated in the same length and utilized as inputs for algorithms to detect the peak pressure and the maximum pressure rise rate. The algorithms are mainly performed on data compression (or feature extraction) and target regression. Major algorithms, such as one-dimensional convolutional neural network, compression sensing, wavelet decomposition, multilayer perceptron, and support vector machine, are tested. Various experimental results verify that for the test engine the phase detection accuracy of the start of combustion and maximum pressure rise rate is less than 1.7°CA for a 95% prediction interval width. For the detection of the peak pressure and maximum pressure rise rate, the normalized error threshold is set as 0.05, then the accuracies can be not less than 95%.

Sign in / Sign up

Export Citation Format

Share Document