Effect of Void Fraction on Pressure Drop in Upward Vertical Two-Phase Gas-Liquid Pipe Flow

2012 ◽  
Author(s):  
Clement C. Tang ◽  
Sanjib Tiwari ◽  
Afshin J. Ghajar
Keyword(s):  
Experimental Data ◽  
Pressure Drop ◽  
Void Fraction ◽  
Gas Velocity ◽  
Two Phase ◽  
Frictional Pressure Drop ◽  
Fraction Increase ◽  
Superficial Gas Velocity ◽  
Two Parameters

Experimental data for void fraction and two-phase frictional pressure drop from various sources has been compiled and analyzed. The experimental data revealed that at lower range of superficial gas velocity and void fraction, the variations of two-phase frictional pressure drop with superficial gas velocity and void fraction are relatively flat. However, as superficial gas velocity and void fraction increase to higher values, the frictional pressure drop became significantly sensitive to the two parameters. In a situation when two-phase pressure drop is sensitive to the variation of void fraction, it is then that proper and accurate characterization of void fraction becomes significant. From the experimental data, regions where pressure drop is sensitive to the variation of void fraction are identified and evaluated.

Effect of Void Fraction on Pressure Drop in Upward Vertical Two-Phase Gas-Liquid Pipe Flow

2013 ◽  
Vol 135 (2) ◽  
Author(s):  
Clement C. Tang ◽  
Sanjib Tiwari ◽  
Afshin J. Ghajar
Keyword(s):  
Experimental Data ◽  
Pressure Drop ◽  
Void Fraction ◽  
Gas Velocity ◽  
Two Phase ◽  
Frictional Pressure Drop ◽  
Fraction Increase ◽  
Superficial Gas Velocity ◽  
Two Parameters

Experimental data for the void fraction and two-phase frictional pressure drop from various sources has been compiled and analyzed. The experimental data revealed that at the lower range of superficial gas velocity and void fraction, the variations of the two-phase frictional pressure drop with superficial gas velocity and void fraction are relatively flat. However, as the superficial gas velocity and void fraction increase to higher values, the frictional pressure drop became significantly sensitive to the two parameters. In a situation when the two-phase pressure drop is sensitive to the variation of the void fraction, it is then that the proper and accurate characterization of the void fraction becomes significant. From the experimental data, regions where the pressure drop is sensitive to the variation of the void fraction are identified and evaluated.

scholarly journals Frictional Pressure Drop and Liquid Holdup of Churn Flow in Vertical Pipes with Different Viscosities

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-8
Author(s):  
Zilong Liu ◽  
Yubin Su ◽  
Ming Lu ◽  
Zilong Zheng ◽  
Ruiquan Liao
Keyword(s):  
Pressure Drop ◽  
Liquid Velocity ◽  
Gas Velocity ◽  
Liquid Holdup ◽  
Two Phase ◽  
Frictional Pressure Drop ◽  
Viscous Oil ◽  
Predicted Values ◽  
Superficial Gas Velocity ◽  
Churn Flow

Churn flow commonly exists in the pipe of heavy oil, and the characteristics of churn flow should be widely understood. In this paper, we carried out air and viscous oil two-phase flow experiments, and the diameter of the test section is 60 mm. The viscosity range of the oil was 100~480 mPa·s. Based on the measured liquid holdup and pressure drop data of churn flow, it can be concluded that, due to the existence of liquid film backflow, positive and negative frictional pressure drop can be found and the change of frictional pressure drop with the superficial gas velocity is related to superficial liquid velocity. With the increase of viscosity, the change rate of frictional pressure drop increases with the increase of the superficial gas velocity. Combining our previous work and the Taitel model, we proposed a new pressure drop model for viscous oil-air two-phase churn flow in vertical pipes. By comparing the predicted values of existing models with the measured pressure drop data, the proposed model has better performance in predicting the pressure drop.

Computation of flow and heat transfer in horizontal gas–solid flows through an adiabatic pipe

2020 ◽  
pp. 095440622093631
Author(s):  
Brundaban Patro ◽  
Kiran K Kupireddi ◽  
Jaya K Devanuri
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Nusselt Number ◽  
Pressure Drop ◽  
Solid Loading ◽  
Gas Velocity ◽  
Two Phase ◽  
Flow And Heat Transfer ◽  
Loading Ratio ◽  
Solid Temperature

The current paper deals with the studies of heat transfer and pressure drop through a horizontal, adiabatic pipe, having gas–solid flows. The inlet air temperature is 443 K, whereas the inlet solid temperature is 308 K. The numerical results are compared with the benchmark experimental data and are agreed satisfactorily. The influences of solid loading ratio, solid diameter and gas velocity on Nusselt number and pressure drop have been studied. The Nusselt number decreases and the pressure drop increases with an increase in the solid diameter. The Nusselt number decreases with an increase in the solid loading ratio at a lower solid diameter of 100 µm. However, at a higher value of solid diameter of 200 µm, the Nusselt number first decreases up to a specific solid loading ratio, and after that, it increases. The pressure drop results show different behaviours with the solid loading ratio. Both the Nusselt number and pressure drop increase with the gas velocity. Finally, a correlation is generated to calculate the two-phase Nusselt number.

Two-Phase Flow Through Square and Circular Microchannels—Effects of Channel Geometry

2004 ◽  
Vol 126 (4) ◽  
pp. 546-552 ◽  
Author(s):  
Peter M.-Y. Chung ◽  
Masahiro Kawaji ◽  
Akimaro Kawahara ◽  
Yuichi Shibata
Keyword(s):  
Pressure Drop ◽  
Void Fraction ◽  
Two Phase Flow ◽  
Flow Characteristics ◽  
Separated Flow ◽  
Phase Flow ◽  
Two Phase ◽  
Channel Geometry ◽  
Frictional Pressure Drop ◽  
Channel Shape

An adiabatic experiment was conducted to investigate the effect of channel geometry on gas-liquid two-phase flow characteristics in horizontal microchannels. A water-nitrogen gas mixture was pumped through a 96 μm square microchannel and the resulting flow pattern, void fraction and frictional pressure drop data were compared with those previously reported by the authors for a 100 μm circular microchannel. The pressure drop data were best estimated using a separated-flow model and the void fraction increased non-linearly with volumetric quality, regardless of the channel shape. However, the flow maps exhibited transition boundaries that were shifted depending on the channel shape.

Evaluation of Two-Phase Frictional Pressure Drop Correlations Against Experimental Data

2019 ◽  
Vol 12 (3) ◽  
Author(s):  
Wei Li ◽  
Kunrong Shen ◽  
Boren Zheng ◽  
Xiang Ma ◽  
S. A. Sherif ◽  
...  
Keyword(s):  
Experimental Data ◽  
Pressure Drop ◽  
Mass Flow ◽  
Flow Model ◽  
Saturation Temperature ◽  
Separated Flow ◽  
Outer Diameter ◽  
Two Phase ◽  
Homogeneous Flow ◽  
Frictional Pressure Drop

Abstract Results are presented here from an experimental investigation on tube side two-phase characteristics that took place in four tested tubes—the 1EHT-1, 1EHT-2, 4LB, and smooth tubes. The equivalent outer diameter of the tube was 9.52 mm and the inner diameter was 8.32 mm. Condensation tests were conducted using refrigerant R410A at a saturation temperature of 318 K, over a mass flow range of 150–450 kg m−2 s−1, with inlet and outlet vapor qualities of 0.8 and 0.2, respectively. Evaporation tests were performed at a saturation temperature of 279 K, over a mass flow range of 150–380 kg m−2 s−1, with inlet and outlet vapor qualities of 0.2 and 0.8, respectively. Pressure drop data of the four tested tubes were collected to evaluate five identified prediction correlations based on the separated flow model and the homogeneous flow model. The separated flow approaches presented predictions with average MAEs of 24.9% and 16.4% for condensation and evaporation data, respectively, while the average MAEs of the homogeneous flow model were 31.6% and 43.4%, respectively. Almost all the identified correlations underestimated the frictional pressure drop of the 4LB tube with MAEs exceeding 30%. An earlier transition of different flow patterns was expected to occur in the EHT tubes while developing a new diabatic flow pattern map is needed for the 4LB tube. A new correlation was presented based on the two-phase multiplier Φ and the Martinelli parameter Xtt, which exhibited excellent predictive results for the experimental data.

Experimental Study on Resistance Characteristics in a 3 × 3 Rod Bundle

2014 ◽  
Author(s):  
Chaoxing Yan ◽  
Changqi Yan ◽  
Licheng Sun ◽  
Yang Wang
Keyword(s):  
Experimental Data ◽  
Experimental Study ◽  
Pressure Drop ◽  
Two Phase Flow ◽  
Phase Flow ◽  
Local Resistance ◽  
Local Pressure ◽  
Two Phase ◽  
Frictional Pressure Drop ◽  
Rod Bundle

Experimental study on resistance of air-water two-phase flow in a vertical 3 × 3 rod bundle was carried out under normal temperature and pressure. The rod diameter and pitch were 8 mm and 11 mm, respectively. The ranges of gas and liquid superficial velocity were 0.013∼3.763 m/s and 0.076∼1.792 m/s, respectively. The result indicated that the existing correlations for calculating frictional coefficient in the rod bundle and local resistance coefficient could not give favorable predictions on the single-phase experimental data. For the case of two-phase flow, eight correlations for calculating two-phase equivalent viscosity poorly predicted the frictional pressure drop, with the mean absolute errors around 60%. Meanwhile, the eight classical two-phase viscosity formulae were evaluated against the local pressure drop at spacer grid. It is shown that Dukler model predicted the experimental data well in the range of Rel<9000 while McAdams correlation was the best for Rel⩾9000. For all the experimental data, Dukler model provided the best prediction with MRE of 29.03%. Furthermore, approaches to calculate two-phase frictional pressure drop and local resistance were proposed by considering mass quality, two-phase Reynolds number and densities in homogenous flow model, resulting in a good agreement with the experimental data.

Optimized Condition for Pairing of Different Friction Factor and Viscosity Equations for the Frictional Pressure Drop of R22 and R290

2019 ◽  
Vol 27 (04) ◽  
pp. 1950037
Author(s):  
Qais Abid Yousif ◽  
Normah Mohd-Ghazali ◽  
Agus Sunjarianto Pamitran ◽  
Yushazaziah Mohd-Yunos
Keyword(s):  
Experimental Data ◽  
Pressure Drop ◽  
Friction Factor ◽  
Environmentally Friendly ◽  
Two Phase ◽  
Frictional Pressure Drop ◽  
Multi Objective Genetic Algorithm ◽  
Percentage Difference ◽  
The Many ◽  
Small Channels

Accurate prediction of the friction factor and consequently the pressure drop of two-phase flow in small channels is still an issue. Many correlations exist for the determination of the viscosity and the friction factor that appear in the frictional pressure drop and their combination often determined the degree of disagreements between the experimental data and predicted outcomes. Demands for environmentally friendly refrigerants have further posed a challenge to find compatible alternatives with as good a performance as the current coolants. Despite the many available correlations developed to date, many more are studied in effort to reduce the discrepancies. This paper presents the outcomes of a study comparing the optimized conditions when three different viscosity equations are paired with eight different friction factor correlations to minimize the frictional pressure drop. The approach used multi-objective genetic algorithm (MOGA) to assist in selecting the best pairing. Comparison is then completed with available experimental data. The study showed that the Blasius friction factor paired with the Dukler viscosity produced the least percentage difference for R22, while when paired with the McAdams viscosity produced a lower difference for R290, an environmentally friendly refrigerant being considered to replace R22.

Experimental Investigation of the Effect of Surface Tension and the Correlation on Void Fraction and Frictional Pressure Drop of an Air-Liquid Two-Phase Flow in a Horizontal Flat Capillary Rectangular Channel

2003 ◽  
Author(s):  
Hideo Ide ◽  
Tohru Fukano
Keyword(s):  
Surface Tension ◽  
Pressure Drop ◽  
Void Fraction ◽  
Two Phase Flow ◽  
Rectangular Channel ◽  
Surfactant Solution ◽  
Phase Flow ◽  
Two Phase ◽  
Frictional Pressure Drop ◽  
Effect Of Surface

Air-liquid two-phase flow in a horizontal flat capillary rectangular channel has been studied to clarify the effects of concentration of surfactant solution on the flow phenomena, such as flow patterns, pressure drop, void fraction and so on. The concentrations of surfactant solution were 0, 10, 50 and 100 ppm and the surface tension of each solution was reduced to about 34mN/m from that of pure water of about 72mN/m. The dimension of the channel used was 10.0 mm × 1.0 mm. The drag reduction by mixing the surfactant was examined in both the single phase flow and the two-phase flow. The experimental data of two-phase frictional pressure drop and holdup were compared with the respective correlations which were previously proposed by the other researchers and the present authors. Finally, we proposed new correlations of two-phase frictional pressure drop and holdup in which the effect of surface tension and the aspect ratio of cross section of channel were taken into account.

Sign in / Sign up

Export Citation Format

Share Document