Rewetting Analysis of Hot Moving Surface by Round Water Jet Impingement

2018 ◽  
Author(s):  
Avadhesh Kumar Sharma ◽  
Mayank Modak ◽  
Santosh K. Sahu
Keyword(s):  
Experimental Investigation ◽  
Reynolds Number ◽  
Thermal Imaging ◽  
Transient Temperature ◽  
Axial Distance ◽  
Initial Surface ◽  
Moving Plate ◽  
Thermal Imaging Camera ◽  
Plate Velocity ◽  
Imaging Camera

Impinging jets are commonly utilized in the run-out table (ROT) cooling in the hot rolling process in steel manufacturing industries. The phenomenon of rapid cooling of a sufficiently hot surface is termed as the quenching. The present paper reports the rewetting behavior of 0.15 mm thick hot moving stainless steel foil (SS-304) by circular impinging jet from bottom side through experimental investigation. The transient temperature of the hot foil is recorded by using thermal imaging camera (A655sc, FLIR system). Tests are performed for a varied range of Reynolds number (Re = 2500–10000), nozzle to plate distance (z/d = 6), moving plate velocity (0–40 mm/s) and initial surface temperature 500±10 °C. Transient temperature obtained from thermal imaging camera is used to evaluate rewetting time and rewetting velocity. Based on the experimental investigation correlation has been proposed to predict non-dimensional rewetting velocity as a function of various parameters, namely, Reynolds number, non-dimensional axial distance and moving plate velocity.

scholarly journals Thermal Imaging Study to Determine the Operational Condition of a Conveyor Belt Drive System Structure

Energies ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3258
Author(s):  
Dawid Szurgacz ◽  
Sergey Zhironkin ◽  
Stefan Vöth ◽  
Jiří Pokorný ◽  
A.J.S. (Sam) Spearing ◽  
...  
Keyword(s):  
Thermal Imaging ◽  
Thermal Condition ◽  
Thermal State ◽  
Operating Time ◽  
Imaging Study ◽  
Conveyor Belt ◽  
System Structure ◽  
Thermal Imaging Camera ◽  
Imaging Camera ◽  
Maintenance Service

The paper discusses the results of a study carried out to determine the thermal condition of a conveyor power unit using a thermal imaging camera. The tests covered conveyors in the main haulage system carrying coal from a longwall. The measurements were taken with a thermal imaging diagnostic method which measures infrared radiation emitted by an object. This technology provides a means of assessing the imminence and severity of a possible failure or damage. The method is a non-contact measuring technique and offers great advantages in an underground mine. The thermograms were analysed by comparing the temperature distribution. An analysis of the operating time of the conveyors was also carried out and the causes of the thermal condition were determined. The main purpose of the research was to detect changes in thermal state during the operation of a belt conveyor that could indicate failure and permit early maintenance and eliminate the chance of a fire. The article also discusses the construction and principle of operation of a thermal imaging camera. The findings obtained from the research analysis on determining the thermal condition of the conveyor drive unit are a valuable source of information for the mine’s maintenance service.

Thermal and Fluid Dynamic Behavior of a Horizontal Channel With Adiabatic Moving Lower Plate

2005 ◽  
Author(s):  
Assunta Andreozzi ◽  
Vincenzo Naso ◽  
Oronzio Manca
Keyword(s):  
Heat Flux ◽  
Reynolds Number ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Horizontal Channel ◽  
Lower Plate ◽  
Stationary Condition ◽  
Moving Plate ◽  
Plate Velocity

In this study a numerical investigation of mixed convection in air in horizontal parallel walled channels with moving lower plate is carried out. The moving lower plate has a constant velocity and it is adiabatic, whereas the upper one is heated at uniform heat flux. The effects of horizontal channel height, heat flux and moving plate velocity are analyzed. Results in terms of temperature and stream function fields are given and the mass flow rate per unit of length and divided by the dynamic viscosity is reported as a function of Reynolds number based on the moving plate velocity. For stationary condition of lower plate, a typical C–loop inside the horizontal channel is detected. Different flow motions are observed in the channel and the two reservoirs, depending on the heat flux values and the distance between the heated upper stationary plate and lower adiabatic moving plate. The dimensionless induced mass flow rate presents different increase between the Reynolds number lower or greater than 1000.

MOEMS thermal imaging camera

2008 ◽  
Author(s):  
M. Fatih Toy ◽  
Onur Ferhanoglu ◽  
Hamdi Torun ◽  
F. Levent Degertekin ◽  
Hakan Urey
Keyword(s):  
Thermal Imaging ◽  
Thermal Imaging Camera ◽  
Imaging Camera

scholarly journals Towards Collection of Smart City Data for Cloud Storage Using UAVs

2021 ◽  
Vol 8 (1) ◽  
pp. 4-9
Author(s):  
Ilia Ageev ◽  
Wolfram Hardt
Keyword(s):  
Data Collection ◽  
Thermal Imaging ◽  
Smart City ◽  
Cloud Storage ◽  
Traffic Analysis ◽  
Thermal Imaging Camera ◽  
Advantages And Disadvantages ◽  
Cloud Server ◽  
Imaging Camera

The article describes the methodology and process of collecting smart city data using drones for cities that do not have a sufficiently developed infrastructure. For storage and subsequent analysis of data, a cloud server is required; TUC DriveCloud is presented as an example of such a server in the article. Traffic analysis and building inspection are described as examples of drone data collection tasks. The advantages and disadvantages of collecting data using a thermal imaging camera are also discussed using the example of the problem of detecting and tracking the movement of people.

Applications of an unmanned aerial vehicle and thermal‐imaging camera to study ducks nesting over water

2020 ◽  
Vol 91 (4) ◽  
pp. 409-420
Author(s):  
Jacob D. Bushaw ◽  
Kevin M. Ringelman ◽  
Michael K. Johnson ◽  
Trenton Rohrer ◽  
Frank C. Rohwer
Keyword(s):  
Unmanned Aerial Vehicle ◽  
Thermal Imaging ◽  
Thermal Imaging Camera ◽  
Imaging Camera ◽  
Aerial Vehicle
Sign in / Sign up

Export Citation Format

Share Document