Secondary Fluids for GAX Absorption Heat Pump

2003 ◽  
Author(s):  
G. Anand ◽  
C. B. Panchal ◽  
D. C. Erickson
Keyword(s):  
Los Angeles ◽  
Natural Gas ◽  
Heat Pump ◽  
Performance Model ◽  
Coefficient Of Performance ◽  
Pumping Power ◽  
Ambient Conditions ◽  
Absorption Heat Pump ◽  
Heating And Cooling ◽  
Secondary Fluid

The gas-fired Generator-Absorber heat eXchanger (GAX) heat pump is being considered for space conditioning in residential and light commercial applications. In order to meet the national building codes for ammonia absorption heat pumps, a secondary fluid is used to interface with the air-coils. Proper choice of a secondary fluid maximizes the economic advantage of the GAX heat pump. The secondary fluid transfers the heating and cooling loads from the absorption heat pump to and from outdoor and indoor air-coils. The physical properties of secondary fluids influence the heat transfer performance in the heat-exchange equipment and hence the effective lift, thereby determining the cycle coefficient of performance (COP). Additionally, the pumping power for each fluid varies depending on the density and viscosity at operating temperatures. The variation in cycle COP and pumping power as a result of fluid properties is ultimately manifested as changes in electric and natural-gas cost. An analysis was carried out to evaluate six secondary fluids for a GAX absorption heat pump. A performance model was developed to simulate the secondary-fluid flow loops and the absorption heat pump. The utility costs for heating and cooling were determined for a typical building. The effects of ambient conditions and local utility rates were determined by modeling the annual utility costs in four cities: Atlanta, Chicago, Los Angeles, and New York. These four cities provided wide variations in heating and cooling requirements, and utility rates for natural gas and electricity. The results from this study provide a basis for selecting secondary fluids for heat pumping in different locations.

Absorption Heat Pump Performance Improvement Through Ground Coupling

1997 ◽  
Vol 119 (4) ◽  
pp. 242-249 ◽  
Author(s):  
S. Garimella
Keyword(s):  
Heat Pump ◽  
Coupled System ◽  
Climate Data ◽  
Ambient Conditions ◽  
Cooling Mode ◽  
Heat And Mass Exchange ◽  
Absorption Heat Pump ◽  
Heating And Cooling ◽  
Residential Space ◽  
Heating Mode

The present study investigates the improvement in the performance of an absorption heat pump for residential space-conditioning due to the use of the ground as the heat source in the heating mode and the heat sink in the cooling mode. A baseline air-coupled single-effect ammonia-water heat pump is first designed to deliver 10.55 kW (36,000 Btu/h) of cooling load at the ARI rating conditions. Particular attention is paid to incorporating many realistic details of an operating system such as fuel combustion efficiencies of the burner, nonequilibrium conditions, and moist air processes in the air-coupled heat exchangers. A range of parametric studies is also conducted to investigate the variation in performance of this system with ambient conditions in the heating and cooling modes. The same system is then analyzed in a ground-coupled configuration. The instantaneous COP for the ground-coupled system is compared with the COP of the air-coupled system as a function of the time of the year and the corresponding variations in ambient and ground temperatures using 30-yr average climate data for various locations from the National Weather Service. Improvements in COP of up to 20 percent over the air-coupled system values (cooling mode COP of 0.495 at 35°C (95°F) and heating mode COP of 1.20 at 8.33°C (47°F)) are demonstrated in diverse geographic locations with widely varying heating and cooling loads. These improvements indicate that an efficient ground-coupled heat pump could be developed for residential space-conditioning applications using simple thermodynamic cycles and existing technology for the heat and mass exchange components.

Performance Characteristics of a Combined Ejector-Absorption Heat Pump Using NH3-H2O

1999 ◽  
Author(s):  
D. A. Kouremenos ◽  
E. D. Rogdakis ◽  
G. K. Alexis
Keyword(s):  
Heat Pump ◽  
Gain Factor ◽  
Coefficient Of Performance ◽  
Detailed Calculation ◽  
Absorption System ◽  
Evaporator Temperature ◽  
Pump System ◽  
Heat Gain ◽  
Absorption Heat Pump ◽  
Heat Pump System

Abstract Absorption system have been investigated for many years. However, coefficient of performance COP or heat gain factor HGF for absorption systems are significantly lower than those for conventional compression systems. This has restricted their wide application. This paper discusses the behavior of mixture NH3-H2O through of an ejector, operating in an absorption heat pump system. This combination improves the performance of conventional absorption system and with the phasing out of ozone-damaging refrigerants, absorption refrigerators, heat pumps and air-conditioning now provide a potential alternative. For the detailed calculation of the proposed system a method has been developed, which employs analytical functions describing the thermodynamic properties of die mixture. The influence of three major parameters: generator, condenser and evaporator temperature, on ejector efficiency and heat gain factor of the system is discussed. Also the maximum value of HGF was estimated by correlation of above three temperatures.

scholarly journals Heat pump systems: A mini review

2021 ◽  
Vol 4 (2) ◽  
pp. 73-81
Author(s):  
Mohammad Omar Temori ◽  
František Vranay
Keyword(s):  
Heat Pump ◽  
Electricity Consumption ◽  
Cost Savings ◽  
Electrical Energy ◽  
Primary Energy ◽  
Heat Pumps ◽  
Coefficient Of Performance ◽  
Heating And Cooling ◽  
Ground Source ◽  
Reduce Electricity Consumption

In this work, a mini review of heat pumps is presented. The work is intended to introduce a technology that can be used to income energy from the natural environment and thus reduce electricity consumption for heating and cooling. A heat pump is a mechanical device that transfers heat from one environmental compartment to another, typically against a temperature gradient (i.e. from cool to hot). In order to do this, an energy input is required: this may be mechanical, electrical or thermal energy. In most modern heat pumps, electrical energy powers a compressor, which drives a compression - expansion cycle of refrigerant fluid between two heat exchanges: a cold evaporator and a warm condenser. The efficiency or coefficient of performance (COP), of a heat pump is defined as the thermal output divided by the primary energy (electricity) input. The COP decreases as the temperature difference between the cool heat source and the warm heat sink increases. An efficient ground source heat pump (GSHP) may achieve a COP of around 4. Heat pumps are ideal for exploiting low-temperature environmental heat sources: the air, surface waters or the ground. They can deliver significant environmental (CO2) and cost savings.

Simulation of an absorption heat pump solar heating and cooling system

Solar Energy ◽  
1983 ◽  
Vol 31 (5) ◽  
pp. 473-482 ◽  
Author(s):  
M.O. McLinden ◽  
S.A. Klein
Keyword(s):  
Heat Pump ◽  
Cooling System ◽  
Solar Heating ◽  
Absorption Heat Pump ◽  
Heating And Cooling

Experimental Study of Heating-Cooling Combined Ground Source Heat Pump System with Horizontal Ground Heat Exchanger

2011 ◽  
Vol 374-377 ◽  
pp. 398-404 ◽  
Author(s):  
Ying Ning Hu ◽  
Ban Jun Peng ◽  
Shan Shan Hu ◽  
Jun Lin
Keyword(s):  
Heat Exchanger ◽  
Heat Exchange ◽  
Heat Pump ◽  
Hot Water ◽  
Coefficient Of Performance ◽  
Ground Heat Exchanger ◽  
Pipe Length ◽  
Pump System ◽  
Heat Pump System ◽  
Heating And Cooling

A hot-water and air-conditioning (HWAC) combined ground sourse heat pump(GSHP) system with horizontal ground heat exchanger self-designed and actualized was presented in this paper. The heat transfer performance for the heat exchanger of two different pipe arrangements, three layers and four layers, respectively, was compared. It showed that the heat exchange quantity per pipe length for the pipe arrangement of three layers and four layers are 18.0 W/m and 15.0 W/m. The coefficient of performance (COP) of unit and system could remain 4.8 and 4.2 as GSHP system for heating water, and the COP of heating and cooling combination are up to 8.5 and 7.5, respectively. The power consumption of hot-water in a whole year is 9.0 kwh/t. The economy and feasibility analysis on vertical and horizontal ground heat exchanger were made, which showed that the investment cost per heat exchange quantity of horizontal ground heat exchanger is 51.4% lower than that of the vertical ground heat exchanger, but the occupied area of the former is 7 times larger than the latter's.

The Performance Improvement of a 70kWe Natural Gas CHP System

2008 ◽  
Author(s):  
Lin Fu ◽  
Xiling Zhao ◽  
Shigang Zhang ◽  
Yi Jiang ◽  
Hui Li ◽  
...  
Keyword(s):  
Heat Exchanger ◽  
Natural Gas ◽  
Heat Pump ◽  
Flue Gas ◽  
Utilization Efficiency ◽  
Outlet Temperature ◽  
Absorption Heat Pump ◽  
Gas Engine ◽  
Innovative System ◽  
Chp System

It is well known that combined heating and power (CHP) generation permits the energy of the fuel to be more efficiently than electric and thermal separate generation. The paper deals with natural gas CHP system with a 70kWe gas-powered internal combustion engine (ICE), which has been set up at the Tsinghua University energy-saving building, in Beijing, China. The system is composed of an ICE, a flue gas heat exchanger and other heat exchangers. The conventional system’s characteristics is that the gas engine generates power on-site, and the exhaust of the gas engine is recovered by a high temperature flue gas-water heat exchanger, and the jacket water heat is recovered by a water-water heat exchanger to supply heat for district heating system. In order to improve the system’s performance, an innovative system with absorption heat pump is adopted. The exhaust of the gas engine drives an absorption heat pump to recover the flue gas sensible heat and further recover the latent heat, so the outlet temperature of the exhaust could be lowered to 50°C. In this paper, the electrical and thermal performance of the innovative system were tested and compared with conventional cogeneration systems. The test and comparison results show that the innovative CHP system could increase the heat utilization efficiency 10% in winter. All the results provide important insight into CHP performance characteristics and could be valuable references for CHP system’s improvements.

scholarly journals Comparison of Transcritical CO2 and Conventional Refrigerant Heat Pump Water Heaters for Domestic Applications

Energies ◽  
2019 ◽  
Vol 12 (3) ◽  
pp. 479
Author(s):  
Ignacio Paniagua ◽  
Ángel Álvaro ◽  
Javier Martín ◽  
Celina Fernández ◽  
Rafael Carlier
Keyword(s):  
Heat Pump ◽  
Thermodynamic Cycle ◽  
Heat Pumps ◽  
Design Tool ◽  
Operating Conditions ◽  
Hot Water ◽  
Coefficient Of Performance ◽  
Ambient Conditions ◽  
Water Heater ◽  
Water Heaters

Although CO 2 as refrigerant is well known for having the lowest global warming potential (GWP), and commercial domestic heat pump water heater systems exist, its long expected wide spread use has not fully unfolded. Indeed, CO 2 poses some technological difficulties with respect to conventional refrigerants, but currently, these difficulties have been largely overcome. Numerous studies show that CO 2 heat pump water heaters can improve the coefficient of performance (COP) of conventional ones in the given conditions. In this study, the performances of transcritical CO 2 and R410A heat pump water heaters were compared for an integrated nearly zero-energy building (NZEB) application. The thermodynamic cycle of two commercial systems were modelled integrating experimental data, and these models were then used to analyse both heat pumps receiving and producing hot water at equal temperatures, operating at the same ambient temperature. Within the range of operation of the system, it is unclear which would achieve the better COP, as it depends critically on the conditions of operation, which in turn depend on the ambient conditions and especially on the actual use of the water. Technology changes on each side of the line of equal performance conditions of operation (EPOC), a useful design tool developed in the study. The transcritical CO 2 is more sensitive to operating conditions, and thus offers greater flexibility to the designer, as it allows improving performance by optimising the global system design.

scholarly journals Performance Analysis of Heat Pump Dryer with Unit-Room in Cold Climate Regions

Energies ◽  
2019 ◽  
Vol 12 (16) ◽  
pp. 3125 ◽  
Author(s):  
Yuan ◽  
Lin ◽  
Mao ◽  
Li ◽  
Yang ◽  
...  
Keyword(s):  
Heat Pump ◽  
Ambient Air ◽  
Open Loop ◽  
Cold Climate ◽  
Coefficient Of Performance ◽  
Ambient Conditions ◽  
Total Energy Consumption ◽  
Ambient Temperatures ◽  
Moisture Extraction ◽  
Modelling System

This study presents the development and evaluation of a novel partially open-loop heat pump dryer with a unit-room (HPDU). The unit-room was designed to enable the ambient air to be mixed with the return air, thereby reducing the influence of the ambient air on the system performance, while maintaining a high system thermal efficiency. A modelling system for the HPDU was developed and validated based on a real-scale experimental study. By using the modelling system, the system characteristics under different ambient conditions and bypass factors were analyzed. The energy benefit of the proposed HPDU was quantified through a comparative study with a closed-loop heat pump dryer (CHPD). It is evident that a maximal specific moisture extraction rate (SMER) and a minimal total energy consumption (TEC) existed when changing the bypass factor of the HPDU under certain ambient temperatures. Compared to the CHPD, the coefficient of performance (COP) of the HPDU increased by up to 39.56%, presenting a significant energy benefit for the application of HPDU.

Sign in / Sign up

Export Citation Format

Share Document