Flow Investigations in an Aero Gas Turbine Engine Afterburner

2005 ◽  
Author(s):  
S. Suresh Kumar ◽  
V. Ganesan
Keyword(s):  
Gas Turbine ◽  
Flow Analysis ◽  
Three Dimensional ◽  
Simple Algorithm ◽  
Reacting Flow ◽  
Isothermal Model ◽  
Turbine Engine ◽  
Turbulence Effects ◽  
Dissipation Model ◽  
Volume Method

This paper is concerned with the prediction of flow and flame characteristics behind complex flame stabilizer used in aero gas turbine afterburners. The numerical calculation is performed using SIMPLE algorithm with unstructured grid arrangement in which time averaged transport equation for mass, momentum, turbulence and energy are solved using finite volume method. The turbulence effects are simulated using RNG κ-ε model. Flow analysis has been carried out for the non-reacting and reacting conditions. Meshing of the flow domain is done in GAMBIT. A detailed analysis of non-reacting flow in a 60°sector afterburner from inlet to exit of the afterburner is carried out in FLUENT solver code. The various thermodynamic properties are analyzed and presented along the length of the afterburner. Three different combustion models viz. prePDF, eddy dissipation and finite rate/eddy dissipation model are used in order to predict the reacting flow. An experimental investigation of the three-dimensional confined flow fields behind a “V” shaped complex flame stabilizer in an isothermal model of an afterburner is carried out to validate the CFD code. From the present study it is concluded that the prediction procedure adopted especially for non-reacting flow can be used with confidence in the development of an afterburner at a lower cost. Since measurements were not possible under reacting conditions no attempt has been made for reacting flow validation.

On the Prediction of Swirling Flowfields Found in Axisymmetric Combustor Geometries

1982 ◽  
Vol 104 (3) ◽  
pp. 378-384 ◽  
Author(s):  
D. L. Rhode ◽  
D. G. Lilley ◽  
D. K. McLaughlin
Keyword(s):  
Gas Turbine ◽  
Fluid Dynamic ◽  
Three Dimensional ◽  
Boundary Representation ◽  
Reacting Flow ◽  
Gas Turbine Combustor ◽  
Turbine Engine ◽  
Research Activities ◽  
Gradual Expansion ◽  
Neutrally Buoyant

Combustor modeling has reached the stage where the most useful research activities are likely to be on specific sub-problems of the general three-dimensional turbulent reacting flow problem. The present study is concerned with a timely fluid dynamic research task of interest to the combustor modeling community. Numerical computations have been undertaken for a basic two-dimensional axisymmetric flowfield which is similar to that found in a conventional gas turbine combustor. A swirling nonreacting flow enters a larger chamber via a sudden or gradual expansion. The calculation method includes a stairstep boundary representation of the expansion flow, a conventional k-ε turbulence model and realistic accommodation of swirl effects. The results include recirculation zone characterization and predicted mean streamline patterns. In addition, an experimental evaluation using flow visualization of neutrally-buoyant helium-filled soap bubbles is yielding very promising results. Successful outcomes of the work can be incorporated into the more combustion- and hardware-oriented activities of gas turbine engine manufacturers, including incorporating the modeling aspects into already existing comprehensive numerical solution procedures.

Account of Film Turbulence for Predicting Film Cooling Effectiveness in Gas Turbine Combustors

1979 ◽  
Author(s):  
G. J. Sturgess
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Cooling Effectiveness ◽  
Turbine Engine ◽  
Film Cooling Effectiveness ◽  
Wide Range ◽  
Engine Combustion ◽  
Turbulence Effects ◽  
The Impact ◽  
Combustor Liner

The paper deals with a small but important part of the overall gas turbine engine combustion system and continues earlier published work on turbulence effects in film cooling to cover the case of film turbulence. Film cooling of the gas turbine combustor liner imposes certain geometric limitations on the coolant injection device. The impact of practical film injection geometry on the cooling is one of increased rates of film decay when compared to the performance from idealized injection geometries at similar injection conditions. It is important to combustor durability and life estimation to be able to predict accurately the performance obtainable from a given practical slot. The coolant film is modeled as three distinct regions, and the effects of injection slot geometry on the development of each region are described in terms of film turbulence intensity and initial circumferential non-uniformity of the injected coolant. The concept of the well-designed slot is introduced and film effectiveness is shown to be dependent on it. Only slots which can be described as well-designed are of interest in practical equipment design. A prediction procedure is provided for well-designed slots which describes growth of the film downstream of the first of the three film regions. Comparisons of predictions with measured data are made for several very different well-designed slots over a relatively wide range of injection conditions, and good agreement is shown.

Gas Turbine Engine Test Cell Modeling

1990 ◽  
Author(s):  
D. Salinas ◽  
E. E. Cooper
Keyword(s):  
Kinetic Energy ◽  
Gas Turbine ◽  
Three Dimensional ◽  
Gas Turbine Engine ◽  
Test Cell ◽  
Dimensional System ◽  
Engine Test ◽  
Turbine Engine ◽  
Coordinate Model ◽  
Cartesian Coordinate

A numerical simulation of the aerothermal characteristics of a gas turbine engine test cell is presented. The three-dimensional system is modeled using the PHOENICS computational fluid dynamics code. Results predict the velocity field, temperatures, pressures, kinetic energy of turbulence, and dissipation rates of turbulent kinetic energy. Numerical results from two versions, a cartesian coordinate model and a body fitted coordinate model, are compared to experimental data. The comparison shows good quantitative and very good qualitative agreement, suggesting that numerical modeling would be useful in the preliminary design of gas turbine test facilities.

Account of Film Turbulence for Predicting Film Cooling Effectiveness in Gas Turbine Combustors

1980 ◽  
Vol 102 (3) ◽  
pp. 524-534 ◽  
Author(s):  
G. J. Sturgess
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Cooling Effectiveness ◽  
Turbine Engine ◽  
Film Cooling Effectiveness ◽  
Wide Range ◽  
Engine Combustion ◽  
Turbulence Effects ◽  
The Impact ◽  
Combustor Liner

The paper deals with a small but important part of the overall gas turbine engine combustion system and continues earlier published work on turbulence effects in film cooling to cover the case of film turbulence. Film cooling of the gas turbine combustor liner imposes certain geometric limitations on the coolant injection device. The impact of practical film injection geometry on the cooling is one of increased rates of film decay when compared to the performance from idealized injection geometries at similar injection conditions. It is important to combustor durability and life estimation to be able to predict accurately the performance obtainable from a given practical slot. The coolant film is modeled as three distinct regions, and the effects of injection slot geometry on the development of each region are described in terms of film turbulence intensity and initial circumferential non-uniformity of the injected coolant. The concept of the well-designed slot is introduced and film effectiveness is shown to be dependent on it. Only slots which can be described as well-designed are of interest in practical equipment design. A prediction procedure is provided for well-designed slots which describes growth of the film downstream of the first of the three film regions. Comparisons of predictions with measured data are made for several very different well-designed slots over a relatively wide range of injection conditions, and good agreement is shown.

Numerical Characterisation of a Gas Turbine Model Combustor Applying Scale-Adaptive Simulation

2009 ◽  
Author(s):  
Axel Widenhorn ◽  
Berthold Noll ◽  
Manfred Aigner
Keyword(s):  
Flow Field ◽  
Gas Turbine ◽  
Mixture Fraction ◽  
Thermal Power ◽  
Three Dimensional ◽  
Combustion Model ◽  
Reacting Flow ◽  
Adaptive Simulation ◽  
Power Load ◽  
Turbine Model

In this contribution the three-dimensional reacting turbulent flow field of a swirl-stabilized gas turbine model combustor is analyzed numerically. The investigated partially premixed and lifted CH4/air flame has a thermal power load of Pth = 35kW and a global equivalence ratio of φ = 0.65. To study the reacting flow field the Scale Adaptive Simulation (SAS) turbulence model in combination with the Eddy Dissipation/Finite Rate Chemistry combustion model was applied. The simulations were performed using the commercial CFD software package ANSYS CFX-11.0. The numerically achieved time-averaged values of the velocity components and their appropriate turbulent fluctuations (RMS) are in very good agreement with the experimental values (LDA). The same excellent results were found for other flow quantities like temperature and mixture fraction. Here, the corresponding time-averaged and the appropriate RMS profiles are compared to Raman measurements. Furthermore the instantaneous flow features are discussed. In accordance with the experiment the numerical simulation evidences the existence of a precessing vortex core (PVC). The PVC rotates with a frequency of 1596Hz. Moreover it is shown that in the upper part of the combustion chamber a tornado-like vortical structure is established.

Free convective of a linear heterogeneous liquid in a square cavity at side heating

2020 ◽  
pp. 108-116
Author(s):  
K.V. Moiseev ◽  
◽  
V.S. Kuleshov ◽  
R.N. Bakhtizin ◽  
◽  
...  
Keyword(s):  
Control Volume ◽  
Three Dimensional ◽  
Simple Algorithm ◽  
Double Diffusion ◽  
Boussinesq Approximation ◽  
Square Cavity ◽  
Cell Height ◽  
Volume Method ◽  
Dimensional Statement ◽  
Stratified Liquid

In this work the problem of free convection of the Newtonian poorly stratified liquid in the cell warmed up from left and cooled from right with the heat-insulated horizontal boarders is presented. Liquid with small concentration of salt and initial linear stratification on cell height is considered. The model of double diffusion in a Boussinesq approximation is applied to model the process. The problem is solved both in two - and three-dimensional statement by means of a control volume method and a SIMPLE algorithm. It is shown that vortex structures at the layered mode of convection have quasi-two-dimensional character.

Blade Erosion in Automotive Gas Turbine Engine

1995 ◽  
Vol 117 (1) ◽  
pp. 213-219 ◽  
Author(s):  
M. Metwally ◽  
W. Tabakoff ◽  
A. Hamed
Keyword(s):  
Gas Turbine ◽  
Three Dimensional ◽  
Gas Turbine Engine ◽  
Particulate Flow ◽  
Particle Impact ◽  
Surface Erosion ◽  
Blade Surface ◽  
Erosion Model ◽  
Turbine Engine ◽  
Automotive Engine

In this work, a study has been conducted to predict blade erosion and surface deterioration of the free power turbine of an automotive gas turbine engine. The blade material erosion model is based on three-dimensional particle trajectory simulations in the three-dimensional turbine flow field. The particle rebound characteristics after surface impacts were determined from experimental measurements of restitution ratios for blade material samples in a particulate flow tunnel. The trajectories provide the spatial distribution of the particle impact parameters over the blade surfaces. A semi-empirical erosion model, derived from erosion tests of material samples at different particulate flow conditions, is used in the prediction of blade surface erosion based on the trajectory impact data. The results are presented for the three-dimensional particle trajectories through the turbine blade passages, the particle impact locations, blade surface erosion pattern, and the associated erosion parameters. These parameters include impact velocity, impact angle, and impact frequency. The data can be used for life prediction and performance deterioration of the automotive engine under investigation.

Sign in / Sign up

Export Citation Format

Share Document