Development and Validation of a Three-Dimensional Finite Element Model of Cervical Spine (C3-C5)

2010 ◽  
Author(s):  
N. Bahramshahi ◽  
H. Ghaemi ◽  
K. Behdinan
Keyword(s):  
Finite Element ◽  
Cervical Spine ◽  
Three Dimensional ◽  
Element Model ◽  
Intervertebral Discs ◽  
Fe Model ◽  
Two Phase ◽  
Finite Element Software ◽  
Flexion Extension ◽  
Disc Bulge

The objective of this investigation is to develop a detailed, non-linear asymmetric three-dimensional anatomically and mechanically accurate FE model of complete middle cervical spine (C3-C5) using Hypermesh and MSC.Marc software. To achieve this goal, the components of the cervical spine are modeled using 20-noded hexagonal elements. The model includes the intervertebral disc, cortical bone, cancellous bone, endplates, and ligaments. The structure and dimensions of each spinal component are compared with experimentally measured values. In addition, the soil mechanics formulation of MSC.Marc finite element software is applied to model the mechanical behaviour of vertebrae and intervertebral discs as linear isotropic two-phase (biphasic) material. The FE simulation is conducted to investigate compression, flexion\extension and right\Left lateral bending modes. The simulation results are validated and compared closely with the published experimental data and the existing FE models. In general, results show greater flexibility in flexion and less flexibility in extension. The flexion/extension curves are asymmetric with a greater magnitude in flexion than in extension. In addition, the variations of the predicted lateral C4-C5 disc bulge are investigated and the results show that the maximum disc bulge occurs at the C4-C5 anterior location.

scholarly journals Finite element analysis of middle cervical spine

2021 ◽  
Author(s):  
Noushin Bahramshahi
Keyword(s):  
Spinal Cord ◽  
Finite Element ◽  
Cervical Spine ◽  
Three Dimensional ◽  
Spinal Column ◽  
Element Model ◽  
Published Data ◽  
Element Analysis ◽  
Flexion Extension ◽  
Disc Bulge

The spinal cord may be injured through various spinal column injury patterns. However, the relationship between column injury pattern and cord damage is not well understood. This investigation was conducted to develop a detailed, asymmetric three-dimensional finite element model of the C3-C5 cervical spine. The model was validated by comparing the simulation results obtained in this study with experimental published data. Upon validation of the model, the spinal cord was included into the model the simulation were performed. The disc bulge in the model with spinal cord were measured and compared with the results of the model without spinal cord. The results showed that inclusion of the spinal cord reduced the amount of lateral disc bulged. The results of the analysis of the model with spinal cord showed that in compression, the anterior surface of spinal cord sees more displacement, stress and strain that posterior surface and vice versa for flexion/extension.

scholarly journals Finite element analysis of middle cervical spine

2021 ◽  
Author(s):  
Noushin Bahramshahi
Keyword(s):  
Spinal Cord ◽  
Finite Element ◽  
Cervical Spine ◽  
Three Dimensional ◽  
Spinal Column ◽  
Element Model ◽  
Published Data ◽  
Element Analysis ◽  
Flexion Extension ◽  
Disc Bulge

The spinal cord may be injured through various spinal column injury patterns. However, the relationship between column injury pattern and cord damage is not well understood. This investigation was conducted to develop a detailed, asymmetric three-dimensional finite element model of the C3-C5 cervical spine. The model was validated by comparing the simulation results obtained in this study with experimental published data. Upon validation of the model, the spinal cord was included into the model the simulation were performed. The disc bulge in the model with spinal cord were measured and compared with the results of the model without spinal cord. The results showed that inclusion of the spinal cord reduced the amount of lateral disc bulged. The results of the analysis of the model with spinal cord showed that in compression, the anterior surface of spinal cord sees more displacement, stress and strain that posterior surface and vice versa for flexion/extension.

A Biomechanical Model of Lumbar Spine

2000 ◽  
Author(s):  
Subramanya Uppala ◽  
Robert X. Gao ◽  
Scott Cowan ◽  
K. Francis Lee
Keyword(s):  
Finite Element ◽  
Lumbar Spine ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Biomechanical Model ◽  
Element Model ◽  
Fe Model ◽  
Flexion Extension ◽  
Cortical Shell ◽  
Three Dimensional Finite Element

Abstract The strength and stability of the lumbar spine are determined not only by the bone and muscles, but also by the visco-elastic structures and the interplay between the different components of the spine, such as ligaments, capsules, annulus fibrosis, and articular cartilage. In this paper we present a non-linear three-dimensional Finite Element model of the lumbar spine. Specifically, a three-dimensional FE model of the L4-5 one-motion segment/2 vertebrae was developed. The cortical shell and the cancellous bone of the vertebral body were modeled as 3D isoparametric eight-nodal elements. Finite element models of spinal injuries with fixation devices are also developed. The deformations across the different sections of the spine are observed under the application of axial compression, flexion/extension, and lateral bending. The developed FE models provided input to both the fixture design and experimental studies.

Establishment and validation of finite element model of ossification of cervical posterior longitudinal ligament with intervertebral fusion

2020 ◽  
Author(s):  
Li Hui ◽  
Liu Huiqing ◽  
Zhang Yaning
Keyword(s):  
Finite Element ◽  
Cervical Spine ◽  
Finite Element Model ◽  
Three Dimensional ◽  
Element Model ◽  
Posterior Longitudinal Ligament ◽  
Intervertebral Discs ◽  
Biomechanical Analysis ◽  
Intervertebral Fusion ◽  
Dimensional Finite Element

Abstract [Background ]: To establish a three-dimensional finite element model of ossification of the posterior longitudinal ligament of the cervical spine with intervertebral fusion and verify its effectiveness, and provide a platform for finite element calculation and biomechanical analysis in the later stage.[Method]: Select the Department of Spinal Surgery, Linfen People's Hospital A volunteer imported 719 DICOM format images of cervical spine CT scans into Mimics modeling software to build a preliminary 3D model in the stl format, and used Geomagic Studio 2013 software to refine and refine the 3D model to smooth out noise and generate NURBS surfaces The model was then imported into the finite element analysis software Ansys workbench 15.0, adding ligaments and intervertebral discs, meshing, assigning material properties, and simulating 6 activities of the human cervical spine, and comparing them with references.[Results]: A total of 7 Cervical vertebral body, 1 thoracic vertebral body, 5 intervertebral discs and ligaments, etc., with a total of 320512 nodes and 180905 units. It has a realistic appearance, high degree of detail reduction, and ossification of the cervical longitudinal longitudinal ligament with good geometric similarity Incorporate a three-dimensional finite element model of intervertebral fusion. In flexion and extension, left and right lateral flexion, and axial rotation activity compared with references, there is not much difference.[Conclusion]: OPLL merger interbody fusion dimensional finite element model has good mechanical and geometric similarity after similarity cervical established in this study, the model can provide a platform for the latter to further biomechanical analysis.

A Finite Element Model of the Human Knee Joint for the Study of Tibio-Femoral Contact

2002 ◽  
Vol 124 (3) ◽  
pp. 273-280 ◽  
Author(s):  
Tammy L. Haut Donahue ◽  
M. L. Hull ◽  
Mark M. Rashid ◽  
Christopher R. Jacobs
Keyword(s):  
Finite Element ◽  
Articular Cartilage ◽  
Three Dimensional ◽  
Element Model ◽  
Maximum Pressure ◽  
Contact Behavior ◽  
Element Size ◽  
Solid Models ◽  
Flexion Extension ◽  
Three Dimensional Coordinate

As a step towards developing a finite element model of the knee that can be used to study how the variables associated with a meniscal replacement affect tibio-femoral contact, the goals of this study were 1) to develop a geometrically accurate three-dimensional solid model of the knee joint with special attention given to the menisci and articular cartilage, 2) to determine to what extent bony deformations affect contact behavior, and 3) to determine whether constraining rotations other than flexion/extension affects the contact behavior of the joint during compressive loading. The model included both the cortical and trabecular bone of the femur and tibia, articular cartilage of the femoral condyles and tibial plateau, both the medial and lateral menisci with their horn attachments, the transverse ligament, the anterior cruciate ligament, and the medial collateral ligament. The solid models for the menisci and articular cartilage were created from surface scans provided by a noncontacting, laser-based, three-dimensional coordinate digitizing system with an root mean squared error (RMSE) of less than 8 microns. Solid models of both the tibia and femur were created from CT images, except for the most proximal surface of the tibia and most distal surface of the femur which were created with the three-dimensional coordinate digitizing system. The constitutive relation of the menisci treated the tissue as transversely isotropic and linearly elastic. Under the application of an 800 N compressive load at 0 degrees of flexion, six contact variables in each compartment (i.e., medial and lateral) were computed including maximum pressure, mean pressure, contact area, total contact force, and coordinates of the center of pressure. Convergence of the finite element solution was studied using three mesh sizes ranging from an average element size of 5 mm by 5 mm to 1 mm by 1 mm. The solution was considered converged for an average element size of 2 mm by 2 mm. Using this mesh size, finite element solutions for rigid versus deformable bones indicated that none of the contact variables changed by more than 2% when the femur and tibia were treated as rigid. However, differences in contact variables as large as 19% occurred when rotations other than flexion/extension were constrained. The largest difference was in the maximum pressure. Among the principal conclusions of the study are that accurate finite element solutions of tibio-femoral contact behavior can be obtained by treating the bones as rigid. However, unrealistic constraints on rotations other than flexion/extension can result in relatively large errors in contact variables.

FEBio finite element model of a pediatric cervical spine

2021 ◽  
pp. 1-7
Author(s):  
Sean M. Finley ◽  
J. Harley Astin ◽  
Evan Joyce ◽  
Andrew T. Dailey ◽  
Douglas L. Brockmeyer ◽  
...  
Keyword(s):  
Finite Element ◽  
Cervical Spine ◽  
Finite Element Model ◽  
Material Properties ◽  
Surgical Simulation ◽  
Element Model ◽  
Axial Stiffness ◽  
Published Data ◽  
Axial Tension ◽  
Flexion Extension

OBJECTIVE The underlying biomechanical differences between the pediatric and adult cervical spine are incompletely understood. Computational spine modeling can address that knowledge gap. Using a computational method known as finite element modeling, the authors describe the creation and evaluation of a complete pediatric cervical spine model. METHODS Using a thin-slice CT scan of the cervical spine from a 5-year-old boy, a 3D model was created for finite element analysis. The material properties and boundary and loading conditions were created and model analysis performed using open-source software. Because the precise material properties of the pediatric cervical spine are not known, a published parametric approach of scaling adult properties by 50%, 25%, and 10% was used. Each scaled finite element model (FEM) underwent two types of simulations for pediatric cadaver testing (axial tension and cardinal ranges of motion [ROMs]) to assess axial stiffness, ROM, and facet joint force (FJF). The authors evaluated the axial stiffness and flexion-extension ROM predicted by the model using previously published experimental measurements obtained from pediatric cadaveric tissues. RESULTS In the axial tension simulation, the model with 50% adult ligamentous and annulus material properties predicted an axial stiffness of 49 N/mm, which corresponded with previously published data from similarly aged cadavers (46.1 ± 9.6 N/mm). In the flexion-extension simulation, the same 50% model predicted an ROM that was within the range of the similarly aged cohort of cadavers. The subaxial FJFs predicted by the model in extension, lateral bending, and axial rotation were in the range of 1–4 N and, as expected, tended to increase as the ligament and disc material properties decreased. CONCLUSIONS A pediatric cervical spine FEM was created that accurately predicts axial tension and flexion-extension ROM when ligamentous and annulus material properties are reduced to 50% of published adult properties. This model shows promise for use in surgical simulation procedures and as a normal comparison for disease-specific FEMs.

scholarly journals Low Cost Frictional Seismic Base-Isolation of Residential New Masonry Buildings in Developing Countries: A Small Masonry House Case Study

2017 ◽  
Vol 11 (1) ◽  
pp. 1026-1035 ◽  
Author(s):  
Ahmad Basshofi Habieb ◽  
Gabriele Milani ◽  
Tavio Tavio ◽  
Federico Milani
Keyword(s):  
Finite Element ◽  
Seismic Vulnerability ◽  
Base Isolation ◽  
Low Cost ◽  
Element Model ◽  
Shaking Table ◽  
Fe Model ◽  
Isolation System ◽  
Finite Element Software ◽  
Non Linear

Introduction:An advanced Finite Element model is presented to examine the performance of a low-cost friction based-isolation system in reducing the seismic vulnerability of low-class rural housings. This study, which is mainly numerical, adopts as benchmark an experimental investigation on a single story masonry system eventually isolated at the base and tested on a shaking table in India.Methods:Four friction isolation interfaces, namely, marble-marble, marble-high-density polyethylene, marble-rubber sheet, and marble-geosynthetic were involved. Those interfaces differ for the friction coefficient, which was experimentally obtained through the aforementioned research. The FE model adopted here is based on a macroscopic approach for masonry, which is assumed as an isotropic material exhibiting damage and softening. The Concrete damage plasticity (CDP) model, that is available in standard package of ABAQUS finite element software, is used to determine the non-linear behavior of the house under non-linear dynamic excitation.Results and Conclusion:The results of FE analyses show that the utilization of friction isolation systems could much decrease the acceleration response at roof level, with a very good agreement with the experimental data. It is also found that systems with marble-marble and marble-geosynthetic interfaces reduce the roof acceleration up to 50% comparing to the system without isolation. Another interesting result is that there was little damage appearing in systems with frictional isolation during numerical simulations. Meanwhile, a severe state of damage was clearly visible for the system without isolation.

Finite Element Analysis of the Effect of Surface Hardening Depth in Port Crane Wheel

2011 ◽  
Vol 291-294 ◽  
pp. 3282-3286 ◽  
Author(s):  
Jiang Wei Wu ◽  
Peng Wang
Keyword(s):  
Finite Element ◽  
Surface Hardening ◽  
Three Dimensional ◽  
Element Model ◽  
Contact Stresses ◽  
Numerical Results ◽  
Element Analysis ◽  
Finite Element Software ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

In port crane industry, the surface hardening technique is widely used in order to improve the strength of wheel. But the hardening depth is chosen only by according to the experience, and the effect of different hardened depths is not studied theoretically. In this paper, the contact stresses in wheel with different hardening depth have been analyzed by applying three-dimensional finite element model. Based on this model, the ANSYS10.0 finite element software is used. The elastic wheel is used to verify the numerical results with the Hertz’s theory. Three different hardening depths, namely 10mm, 25mm and whole hardened wheel, under three different vertical loads were applied. The effect of hardening depth of a surface hardened wheel is discussed by comparing the contact stresses and contact areas from the numerical results.

scholarly journals A robust 3D finite element model for concrete columns confined by FRCM system

2019 ◽  
Vol 281 ◽  
pp. 01006 ◽  
Author(s):  
Majid M.A. Kadhim ◽  
Mohammed J Altaee ◽  
Ali Hadi Adheem ◽  
Akram R. Jawdhari
Keyword(s):  
Finite Element ◽  
Cement Mortar ◽  
Three Dimensional ◽  
Concrete Columns ◽  
Element Model ◽  
Fe Model ◽  
3D Finite Element ◽  
Composite Failure ◽  
Global Buckling ◽  
Fibre Reinforced Polymer

Fibre reinforced cementitious matric (FRCM) is a recent application of fibre reinforced polymer (FRP) reinforcement, developed to overcome several limitations associated with the use of organic adhesive [e.g. epoxies] in FRPs. It consists of two dimensional FRP mesh saturated with a cement mortar, which is inorganic in nature and compatible with concrete and masonry substrates. In this study, a robust three-dimensional (3D) finite element (FE) model has been developed to study the behaviour of slender reinforced concrete columns confined by FRCM jackets, and loaded concentrically and eccentrically. The model accounts for material nonlinearities in column core and cement mortar, composite failure of FRP mesh, and global buckling. The model response was validated against several laboratory tests from literature, comparing the ultimate load, load-lateral deflection and failure mode. Maximum divergence between numerical and experimental results was 12%. Following the validation, the model will be used later in a comprehensive parametric analysis to gain a profound knowledge of the strengthening system, and examine the effects of several factors expected to influence the behaviour of confined member.

A finite element model to study the effect of porosity location on the elastic modulus of a cantilever beam

2019 ◽  
Vol 43 (4) ◽  
pp. 443-453
Author(s):  
Stephen M. Handrigan ◽  
Sam Nakhla
Keyword(s):  
Finite Element ◽  
Elastic Modulus ◽  
Focused Ion Beam ◽  
Mechanical Response ◽  
Ion Beam ◽  
Three Dimensional ◽  
Beam Theory ◽  
Element Model ◽  
Fe Model ◽  
Three Dimensional Finite Element

An investigation to determine the effect of porosity concentration and location on elastic modulus is performed. Due to advancements in testing methods, the manufacturing and testing of microbeams to obtain mechanical response is possible through the use of focused ion beam technology. Meanwhile, rigorous analysis is required to enable accurate extraction of the elastic modulus from test data. First, a one-dimensional investigation with beam theory, Euler–Bernoulli and Timoshenko, was performed to estimate the modulus based on load-deflection curve. Second, a three-dimensional finite element (FE) model in Abaqus was developed to identify the effect of porosity concentration. Furthermore, the current work provided an accurate procedure to enable accurate extraction of the elastic modulus from load-deflection data. The use of macromodels such as beam theory and three-dimensional FE model enabled enhanced understanding of the effect of porosity on modulus.

Sign in / Sign up

Export Citation Format

Share Document