Dimensional Analysis of Thermal Fields Surrounding Friction Stir Welding Process

2014 ◽  
Author(s):  
Lewis N. Payton ◽  
Vishnu Vardhan Chandrasekaran ◽  
Wesley S. Hunko
Keyword(s):  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Welding Process ◽  
Temperature Fields ◽  
Analytical Comparison ◽  
Friction Stir ◽  
Thermal Fields ◽  
Designed Experiment ◽  
Pi Theorem ◽  
Alloy 6061

A dimensionless correlation is developed based on Buckingham’s Pi-Theorem to estimate the temperature fields generated by the movement of a tool during the Friction Stir Welding of an aluminum alloy (6061-T6). Symmetrical thermocouple measurements are taken during a statistically designed experiment using different factor levels (RPM, Traverse, etc). Analytical comparison (using multivariate ANOVA) validates the predicted dimensionless correlation including the often-reported difference between the advancing versus retreating side of the Friction Stir Tool.

Influence of Different Anvil Back Plates on Heat Dissipation Velocity of the Micro-Friction Stir Welding Process

2015 ◽  
Vol 786 ◽  
pp. 415-420 ◽  
Author(s):  
Wan Shun Chu ◽  
Farazila binti Yusof
Keyword(s):  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Heat Dissipation ◽  
Welding Process ◽  
Temperature Fields ◽  
Thin Sheets ◽  
Friction Stir ◽  
Conventional Steel ◽  
Back Plate ◽  
Two Temperature

The objective of this study is to investigate effects of different anvil back plates on heat dissipation velocity of the micro-friction stir welding (micro-FSW or) process. For this purpose, temperature field simulations are conducted for the micro-friction stir welding of AA5083-H323 aluminum alloy thin sheets by using the ceramic anvil back plate and conventional steel anvil back plate, respectively. Comparing the obtained two temperature fields, it is found that the ceramic anvil back plate significantly decreases the heat dissipation velocity of the micro-FSW process.

EFFECT OF PRE-HEATING ON THE MECHANICAL PROPERTIES OF FRICTION STIR WELDING FOR 6061 ALUMINUM ALLOY

2021 ◽  
Vol 25 (Special) ◽  
pp. 2-124-2-134
Author(s):  
Omer T. Abbas ◽  
◽  
Abbas A. Ayoub ◽  
Fouad A. Saleh ◽  
◽  
...  
Keyword(s):  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Welding Process ◽  
Fusion Welding ◽  
Friction Stir ◽  
Aluminum Alloy 6061 ◽  
Wide Range ◽  
Wrought Aluminum ◽  
Solid State Joining ◽  
Alloy 6061

Friction stir welding (FSW) process is a solid-state joining invented via the Welding Institute in 1991 at a great rate emerging as an application by fusion welding for joining different alloys. The wrought aluminum alloy 6061 is heat treatable and possesses a high corrosion resistance. This alloy has been used in a wide range of applications, like arenas gymnasiums and trains bodies. Aluminum alloy 6061 cannot be easily welded by the conventional fusion welding process because of the cracks that make the mechanical of welding joint very weak. In FSW, many parameters effect on its welding process. In the present research, the pre-heating effect on the aluminum 6061 sheet at 100°C and 150°C was studied. This heat has to be given for obtaining a defect-free as well as quality joint. Result manifested that the welding without pre-heating the parent metal at a (1120 r.p.m) rotational speed and a (30 mm/min) welding speed gave the best result of the ultimate tensile strength (236 N/mm2).

On the problem of tool destruction when obtaining fixed joints of thick-walled aluminum alloy blanks by friction welding with mixing

2021 ◽  
Vol 23 (3) ◽  
pp. 72-83
Author(s):  
Kirill Kalashnikov ◽  
◽  
Andrey Chumaevskii ◽  
Tatiana Kalashnikova ◽  
Aleksey Ivanov ◽  
...  
Keyword(s):  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Friction Welding ◽  
Welding Process ◽  
High Strength ◽  
Heterogeneous Structure ◽  
Adhesive Interaction ◽  
Friction Stir ◽  
Tool Shoulder ◽  
Electric Erosion

Introduction. Among the technologies for manufacturing rocket and aircraft bodies, marine vessels, and vehicles, currently, more and more attention is paid to the technology of friction stir welding (FSW). First of all, the use of this technology is necessary where it is required to produce fixed joints of high-strength aluminum alloys. In this case, special attention should be paid to welding thick-walled blanks, as fixed joints with a thickness of 30.0 mm or more are the target products in the rocket-space and aviation industries. At the same time, it is most prone to the formation of defects due to uneven heat distribution throughout the height of the blank. It can lead to a violation of the adhesive interaction between the weld metal and the tool and can even lead to a destruction of the welding tool. The purpose of this work is to reveal regularities of welding tool destruction depending on parameters of friction stir welding process of aluminum alloy AA5056 fixed joints with a thickness of 35.0 mm. Following research methods were used in the work: the obtaining of fixed joints was carried out by friction welding with mixing, the production of samples for research was carried out by electric erosion cutting, the study of samples was carried out using optical metallography methods. Results and discussion. As a result of performed studies, it is revealed that samples of aluminum alloy with a thickness of 35.0 mm have a heterogeneous structure through the height of weld. There are the tool shoulder effect zone and the pin effect zone, in which certain whirling of weld material caused by the presence of grooves on tool surface is distinctly distinguished. It is shown that the zone of shoulders effect is the most exposed to the formation of tunnel-type defects because of low loading force and high welding speeds. It is revealed that tool destruction occurs tangentially to the surface of the tool grooves due to the high tool load and high welding speeds.

Heat Transfer Simulations and Analysis of Joint Cross-Sectional Microstructure on Friction Stir Welding between Steel and Aluminium

2020 ◽  
Vol 863 ◽  
pp. 85-95
Author(s):  
Truong Minh Nhat ◽  
Truong Quoc Thanh ◽  
Tu Vinh Thong ◽  
Tran Trong Quyet ◽  
Luu Phuong Minh
Keyword(s):  
Tensile Strength ◽  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Thermal Contact ◽  
Welding Process ◽  
Welding Parameters ◽  
Thermal Imager ◽  
Sem Images ◽  
Cross Sectional ◽  
Friction Stir

This study presents conducted heat simulations and experimental jointing flat-plate of aluminum alloy 6061 and SUS 304. Temperature is simulated by the COMSOL software in three states: (1) Preheat the Friction Stir Welding (FSW) by TIG welding, (2) Thermal contact resistance between Aluminium and steel, and (3) The welding process using stiring friction is simulated. The simulations intended to predicting the temperature which is used for preheat and welding process to ensuring the required solid-state welding. The temperature is also determined and checked by a thermal imager comparing with simulation results. Besides, the results of tensile strength is carried out. The Box - Behnken method is used to identify the relationship between the welding parameters (rotation, speed and offset), temperature and tensile strength. The maximum tensile strength is 77% compared to the strength of aluminum alloy. The optimal set of parameters for the process is n = 676 rpm, v = 46 mm / min and x = 0.6 mm. The optimizing welding parameters to achieving good quality of welding process are described. SEM images to determine some properties of welding materials. This is also the basis for initial research to identify some defects in welding of two different materials (IMC thickness and interconnected pores) and the cause of these defects.

scholarly journals Experimental Investigation of Friction Stir Welding on 6061-T6 Aluminum Alloy using Taguchi-Based GRA

Metals ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1480
Author(s):  
Assefa Asmare ◽  
Raheem Al-Sabur ◽  
Eyob Messele
Keyword(s):  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Process Parameters ◽  
Rotational Speed ◽  
Weight Ratio ◽  
Welding Process ◽  
Quality Criteria ◽  
Alloy Sheet ◽  
Friction Stir ◽  
Weld Joints

The use of aluminum alloys, nowadays, is swiftly growing from the prerequisite of producing higher strength to weight ratio. Lightweight components are crucial interest in most manufacturing sectors, especially in transportation, aviation, maritime, automotive, and others. Traditional available joining methods have an adverse effect on joining these lightweight engineering materials, increasing needs for new environmentally friendly joining methods. Hence, friction stir welding (FSW) is introduced. Friction stir welding is a relatively new welding process that can produce high-quality weld joints with a lightweight and low joining cost with no waste. This paper endeavors to deals with optimizing process parameters for quality criteria on tensile and hardness strengths. Samples were taken from a 5 mm 6061-T6 aluminum alloy sheet with butt joint configuration. Controlled process parameters tool profile, rotational speed and transverse speed were utilized. The process parameters are optimized making use of the combination of Grey relation analysis method and L9 orthogonal array. Mechanical properties of the weld joints are examined through tensile, hardness, and liquid penetrant tests at room temperature. From this research, rotational speed and traverse speed become significant parameters at a 99% confidence interval, and the joint efficiency reached 91.3%.

Sign in / Sign up

Export Citation Format

Share Document