Effect of Spark Ignition Timing on Copper Coated Spark Ignition Engine With Alcohol Blended Gasoline With Catalytic Converter

2015 ◽  
Author(s):  
Maddali V. S. Murali Krishna ◽  
Ch. Indira Priyadarsini ◽  
Y. Nagini ◽  
S. Naga Sarada ◽  
P. Usha Sri ◽  
...  
Keyword(s):  
Combustion Chamber ◽  
Catalytic Converter ◽  
Spark Ignition ◽  
Sponge Iron ◽  
Spark Ignition Engine ◽  
Air Injection ◽  
Ignition Timing ◽  
Full Load ◽  
Full Load Operation ◽  
Improved Performance

This paper reports performance evaluation of four–stroke, single–cylinder, water cooled, variable compression ratio (3–9), variable speed (2200–3000 rpm) spark ignition engine with brake power of 2.2 kW at a speed of 3000 rpm with copper coated combustion chamber (CCE) [copper-(thickness, 300 μ) was coated on piston crown, inner side of liner and cylinder head] with alcohol blended gasoline [20% methanol with 80% gasoline; 20% of ethanol with 80% of gasoline by volume) with varied spark ignition timing provided with catalytic converter with sponge iron as catalyst along with air injection and compared with engine with conventional combustion chamber (CE) with gasoline operation. Performance parameters and exhaust emissions (CO and UBHC) were evaluated at full load operation of the engine. Aldehydes (formaldehyde and acetaldehyde) were measured by wet method of 2,4, dinitrophenyle method at full load operation of the engine. Alcohol blended gasoline operation improved performance and reduced CO and UBHC emissions when compared with gasoline operation with both versions of the combustion chamber. At recommended and injection timing, CCE with test fuels improved performance and reduced pollution levels, when compared with CE. Catalytic converter with sponge iron as catalyst along with air injection significantly reduced pollutants with test fuels.

Effect of injection and ignition timing on a hydrogen-lean stratified charge combustion engine

2021 ◽  
pp. 146808742110346
Author(s):  
Sanguk Lee ◽  
Gyeonggon Kim ◽  
Choongsik Bae
Keyword(s):  
Internal Combustion Engines ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Combustion Stability ◽  
Transport Sector ◽  
Injection Timing ◽  
Ignition Timing ◽  
Particulate Emission ◽  
Stratified Charge ◽  
Lean Limit

Hydrogen can be used as a fuel for internal combustion engines to realize a carbon-neutral transport society. By extending the lean limit of spark ignition engines, their efficiency, and emission characteristics can be improved. In this study, stratified charge combustion (SCC) using monofueled hydrogen direct injection was used to extend the lean limit of a spark ignition engine. The injection and ignition timing were varied to examine their effect on the SCC characteristics. An engine experiment was performed in a spray-guided single-cylinder research engine, and the nitrogen oxide and particulate emissions were measured. Depending on the injection timing, two different types of combustion were characterized: mild and hard combustion. The advancement and retardation of the ignition timing resulted in a high and low combustion stability, respectively. The lubricant-based particulate emission was attributed to the in-cylinder temperature and area of the flame surface. Therefore, the results of the study suggest that the optimization of the hydrogen SCC based on the injection and ignition timing could contribute to a clean and efficient transport sector.

Scavenged Pre-Chamber on a Gas Engine for Light Duty Truck

2016 ◽  
Author(s):  
Jiří Vávra ◽  
Zbyněk Syrovátka ◽  
Michal Takáts ◽  
Eduardo Barrientos
Keyword(s):  
Natural Gas ◽  
Thermal Loading ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Validation Data ◽  
Automotive Engine ◽  
Light Duty ◽  
Full Load Operation ◽  
Gas Fueled ◽  
Light Duty Truck

This work presents an experimental investigation of advanced combustion of extremely lean natural gas / air mixture in a gas fueled automotive engine with a scavenged pre-chamber. The pre-chamber, which was designed and manufactured in-house, is scavenged with natural gas and is installed into a modified cylinder head of a gas fueled engine for a light duty truck. For initial pre-chamber ignition tests and optimizations, the engine is modified into a single cylinder one. The pre-chamber is equipped with a spark plug, fuel supply and a miniature pressure transducer. This arrangement allows a simultaneous crank angle resolved pressure measurement in the pre-chamber and in the main combustion chamber and provides important validation data for computational fluid dynamics (CFD) simulations. The results of the tests and initial optimizations show that the pre-chamber engine is able to operate within a significantly wider range of mixture composition than the conventional spark ignition engine. Full load operation of the pre-chamber engine is feasible with stoichiometric mixture (compatible with a three-way catalyst), without excessive thermal loading of components. At low load operation, the results show low NOx emissions with a high potential to fulfil current and future NOx limits without lean NOx exhaust gas after-treatment. The scavenged pre-chamber helps to increase the combustion rate mainly in the initial phase of combustion. However, significant unburned hydrocarbons emissions due to incomplete combustion need further optimizations. Thermal efficiency of lean operation of the engine with the pre-chamber compared to the conventional spark ignition system operated in stoichiometric conditions shows approximately 13% improvement.

Model-Based Combustion Duration and Ignition Timing Prediction for Combustion Phasing Control of a Spark-Ignition Engine Using In-Cylinder Pressure Sensors

2019 ◽  
Author(s):  
Xin Wang ◽  
Amir Khameneian ◽  
Paul Dice ◽  
Bo Chen ◽  
Mahdi Shahbakhti ◽  
...  
Keyword(s):  
Pressure Sensors ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Spark Ignition Engine ◽  
Combustion Model ◽  
Ignition Timing ◽  
Model Based ◽  
Crank Angle ◽  
Si Engines ◽  
Phasing Control

Abstract Combustion phasing, which can be defined as the crank angle of fifty percent mass fraction burned (CA50), is one of the most important parameters affecting engine efficiency, torque output, and emissions. In homogeneous spark-ignition (SI) engines, ignition timing control algorithms are typically map-based with several multipliers, which requires significant calibration efforts. This work presents a framework of model-based ignition timing prediction using a computationally efficient control-oriented combustion model for the purpose of real-time combustion phasing control. Burn duration from ignition timing to CA50 (ΔθIGN-CA50) on an individual cylinder cycle-by-cycle basis is predicted by the combustion model developed in this work. The model is based on the physics of turbulent flame propagation in SI engines and contains the most important control parameters, including ignition timing, variable valve timing, air-fuel ratio, and engine load mostly affected by combination of the throttle opening position and the previous three parameters. With 64 test points used for model calibration, the developed combustion model is shown to cover wide engine operating conditions, thereby significantly reducing the calibration effort. A Root Mean Square Error (RMSE) of 1.7 Crank Angle Degrees (CAD) and correlation coefficient (R2) of 0.95 illustrates the accuracy of the calibrated model. On-road vehicle testing data is used to evaluate the performance of the developed model-based burn duration and ignition timing algorithm. When comparing the model predicted burn duration and ignition timing with experimental data, 83% of the prediction error falls within ±3 CAD.

Thermophysical Properties of Working Substance and Heat Transfer in a Hydrogen Combustion Engine

2003 ◽  
Author(s):  
T. Shudo ◽  
H. Oka
Keyword(s):  
Heat Transfer ◽  
Combustion Chamber ◽  
Heat Loss ◽  
Thermophysical Properties ◽  
Internal Combustion Engines ◽  
Internal Combustion ◽  
Spark Ignition ◽  
Hydrogen Combustion ◽  
Spark Ignition Engine ◽  
Combustion Engines

Hydrogen is a clean alternative to fossil fuels for internal combustion engines and can be easily used in spark-ignition engines. However, the characteristics of the engines fueled with hydrogen are largely different from those with conventional hydrocarbon fuels. A higher burning velocity and a shorter quenching distance for hydrogen as compared with hydrocarbons bring a higher degree of constant volume and a larger heat transfer from the burning gas to the combustion chamber wall of the engines. Because of the large heat loss, the thermal efficiency of an engine fueled with hydrogen is sometimes lower than that with hydrocarbons. Therefore, the analysis and the reduction of the heat loss are crucial for the efficient utilization of hydrogen in internal combustion engines. The empirical correlations to describe the total heat transferred from the burning gas to the combustion chamber walls are often used to calculate the heat loss in internal combustion engines. However, the previous research by one of the authors has shown that the widely used heat transfer correlations cannot be properly applied to the hydrogen combustion even with adjusting the constants in them. For this background, this research analyzes the relationship between characteristics of thermophysical properties of working substance and heat transfer to the wall in a spark-ignition engine fueled with hydrogen.

Sign in / Sign up

Export Citation Format

Share Document