Mechanical Behavior of As-Fabricated and UV-Cured Lattice Structures Printed Using the CLIP Technology

2017 ◽  
Author(s):  
Anil Saigal ◽  
John R. Tumbleston ◽  
Hendric Vogel
Keyword(s):  
Additive Manufacturing ◽  
Mechanical Behavior ◽  
Relative Density ◽  
Uv Curing ◽  
Elastic Response ◽  
Lattice Structures ◽  
Minimum Diameter ◽  
Strain Behavior ◽  
End Use ◽  
Continuous Liquid Interface Production

In the rapidly growing field of additive manufacturing (AM), the focus in recent years has shifted from prototyping to manufacturing fully functional, ultralight, ultrastiff end-use parts. This research investigates the mechanical behavior of octahedral and octet lattice structured polyacrylate fabricated using Continuous Liquid Interface Production (CLIP) technology based on 3D printing and additive manufacturing processes. Five different octahedral structures and seven different octet structures with relative densities ranging from approximately 0.07 to 0.35 were fabricated by changing the strut diameter. The minimum diameter of the strut elements is 0.50 mm and 0.35 mm for the octahedral and octet structures, respectively. The different relative density structures were tested in compression in the as-fabricated state and after they were UV cured. The compressive stress-strain behavior of the lattice structures observed is typical of cellular structures which include a region of nominally elastic response, yielding, and plastic strain hardening to a peak in strength, followed by a drop in flow stress. It was found that the stiffness and strength of octahedral lattice structures is greater than the stiffness and strength of octet lattice structures at all relative densities for both as printed/fabricated and UV cured parts, and the ratio of stiffness and strength of UV cured parts to as fabricated parts decreases as the relative density increases. However, the ratio of stiffness and strength of UV cured parts to as fabricated parts for octet lattice structures in general is greater than that for octahedral structures. This can be attributed to the relative diameter of the struts and the depth of UV curing.

Mechanical Response of Different Lattice Structures Fabricated Using the CLIP Technology

2016 ◽  
Author(s):  
Anil Saigal ◽  
John R. Tumbleston ◽  
Hendric Vogel
Keyword(s):  
Additive Manufacturing ◽  
Mechanical Response ◽  
Elastic Response ◽  
Lattice Structures ◽  
Rhombic Dodecahedron ◽  
Structured Materials ◽  
Specific Strength ◽  
Strain Behavior ◽  
End Use ◽  
Continuous Liquid Interface Production

In the rapidly growing field of additive manufacturing (AM), the focus in recent years has shifted from prototyping to manufacturing fully functional, ultralight, ultrastiff end-use parts. This research investigates the mechanical behavior of octahedral, octet, vertex centroid, dode, diamond, rhombi octahedron, rhombic dodecahedron and solid lattice structured polyacrylate fabricated using Continuous Liquid Interface Production (CLIP) technology based on 3D printing and additive manufacturing processes. The compressive stress-strain behavior of the lattice structures observed is typical of cellular structures which include a region of nominally elastic response, yielding, plastic strain hardening to a peak in strength, followed by a drop in flow stress to a plateau region and finally rapid hardening associated with contact of the deformed struts with each other as part of densification. It was found that the elastic modulus and strength of the various lattice structured materials are proportional to each other. In addition, it was found that the octahedral, octet and diamond lattice structures are amongst the most efficient based on the measured specific stiffness and specific strength.

Stress-Strain Behavior of an Octahedral and Octet-Truss Lattice Structure Fabricated Using the CLIP Technology

2017 ◽  
Vol 1142 ◽  
pp. 245-249 ◽  
Author(s):  
Anil Saigal ◽  
John Tumbleston
Keyword(s):  
Additive Manufacturing ◽  
3D Printing ◽  
Lattice Structure ◽  
Liquid Interface ◽  
Layer By Layer ◽  
Stress Strain ◽  
Strain Behavior ◽  
Octet Truss ◽  
Continuous Liquid Interface Production ◽  
Similar Density

In the rapidly growing field of additive manufacturing (AM), the focus in recent years has shifted from prototyping to manufacturing fully functional, ultralight, ultrastiff end-use parts. This research investigates the stress-strain behavior of an octahedral-and octet-truss lattice structured polyacrylate fabricated using Continuous Liquid Interface Production (CLIP) technology based on 3D printing and additive manufacturing processes. Continuous Liquid Interface Production (CLIP) is a breakthrough technology that grows parts instead of printing them layer by layer. Lattice structures such as the octahedral-and octet-truss lattice have recently attracted a lot of attention since they are often structurally more efficient than foams of a similar density made from the same material, and the ease with which these structures can now be produced using 3D printing and additive manufacturing. This research investigates the stress-strain behavior under compression of an octahedral-and octet-truss lattice structured polyacrylate fabricated using CLIP technology

Effect of Build Direction in Direct Metal Laser Sintering (DMLS) of Inconel 718 on Microstructure and Mechanical Behavior

2019 ◽  
Author(s):  
Sachin Alya ◽  
Chaitanya Vundru ◽  
Ramesh Singh ◽  
Khushahal Thool ◽  
Indradev Samajdar ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Mechanical Behavior ◽  
Inconel 718 ◽  
Laser Sintering ◽  
Thermal Gradients ◽  
Layer By Layer ◽  
Direct Metal Laser Sintering ◽  
Powder Bed ◽  
Grain Orientations ◽  
End Use

Abstract Additive manufacturing (AM) technology is gaining enormous popularity in the manufacturing industries. The continuous improvements made in the AM processes features development of 3D metallic prototypes as well as fully functional end-use components. Direct Metal Laser Sintering (DMLS) is a pre-placed powder bed based technique, in which a thin layer of powder is place over the build tray and the areas need to be sintered are exposed to the laser. In the current work the microstructural and mechanical behavior of Inconel 718 parts produced by DMLS are investigated. As the DMLS produces parts in a layer by layer fashion, the orientation of parts with respect to the build direction is an important criterion. Microstructure and mechanical properties of the produce differs depending upon the orientation. This paper emphasize on the variation of grain sizes and grain orientations developed in the components built with different orientations. Another common issue with the additive manufacturing is the development of the residual stresses in the components arising due to the differential thermal gradients experienced during processing. The variation of the residual stress generated in the produced parts has also been characterized and modeled.

Anisotropy and Failure in Octahedral Lattice Structure Parts Fabricated Using the FDM Technology

2017 ◽  
Author(s):  
Gian J. Calise ◽  
Anil Saigal
Keyword(s):  
Lattice Structure ◽  
Catalyst Support ◽  
Acrylonitrile Butadiene Styrene ◽  
Elastic Response ◽  
Cellular Structures ◽  
Lattice Structures ◽  
Strain Behavior ◽  
Mechanical Metamaterials ◽  
3D Printers ◽  
Similar Density

Mechanical metamaterials are man-made materials in which the mechanical properties are mainly defined by their structures instead of the properties of each component. Periodic cellular structures consisting of honeycomb, tetrahedral, 3D Kagome and pyramidal truss arrangement of webs or struts have recently attracted a lot of attention since they have a broad range of applications including structural components, energy absorption, heat exchangers, catalyst support, filters and biomaterials. In addition, lattice structures such as the octahedral are being investigated since they are structurally more efficient than foams of a similar density made from the same material, and the ease with which these structures can now be produced using 3D printing and additive manufacturing. This research investigates the mechanical behavior and anisotropy in octahedral lattice structures of two different relative densities fabricated out of Acrylonitrile butadiene styrene (ABS) using Stratasys FDM 360mc and Dimension sst 1200es 3D printers. The machines were used to print octahedral lattice structured parts with struts 1.00 mm in diameter followed by parts with struts 2.6 mm in diameter and tested in compression in three mutually perpendicular directions. The compressive stress-strain behavior of the lattice structures observed is typical of cellular structures which include a region of nominally elastic response, yielding, and plastic strain hardening to a peak in strength, followed by a drop in flow stress. It was found that not only is the stiffness and strength of the as fabricated parts anisotropic but they, in addition to failure, are also a function of the relative density/strut diameter of the structure.

scholarly journals Experimental and Numerical Evaluation of Mechanical Properties of 3D-Printed Stainless Steel 316L Lattice Structures

2021 ◽  
Author(s):  
M. Carraturo ◽  
G. Alaimo ◽  
S. Marconi ◽  
E. Negrello ◽  
E. Sgambitterra ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Mechanical Behavior ◽  
Numerical Simulations ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Lattice Structures ◽  
Stainless Steel 316L ◽  
Research Attention ◽  
Octet Truss

AbstractAdditive manufacturing (AM), and in particular selective laser melting (SLM) technology, allows to produce structural components made of lattice structures. These kinds of structures have received a lot of research attention over recent years due to their capacity to generate easy-to-manufacture and lightweight components with enhanced mechanical properties. Despite a large amount of work available in the literature, the prediction of the mechanical behavior of lattice structures is still an open issue for researchers. Numerical simulations can help to better understand the mechanical behavior of such a kind of structure without undergoing long and expensive experimental campaigns. In this work, we compare numerical and experimental results of a uniaxial tensile test for stainless steel 316L octet-truss lattice specimen. Numerical simulations are based on both the nominal as-designed geometry and the as-build geometry obtained through the analysis of µ-CT images. We find that the use of the as-build geometry is fundamental for an accurate prediction of the mechanical behavior of lattice structures.

Design for laser powder bed additive manufacturing of AlSi12 periodic mesoscale lattice structures

2021 ◽  
Vol 113 (11-12) ◽  
pp. 3599-3612
Author(s):  
Chen Zhang ◽  
Abhishek Banerjee ◽  
Alison Hoe ◽  
Achutha Tamraparni ◽  
Jonathan R. Felts ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Lattice Structures ◽  
Powder Bed

scholarly journals SURFACE ROUGHNESS CONSIDERATIONS IN DESIGN FOR ADDITIVE MANUFACTURING - A LITERATURE REVIEW

2021 ◽  
Vol 1 ◽  
pp. 2841-2850
Author(s):  
Didunoluwa Obilanade ◽  
Christo Dordlofva ◽  
Peter Törlind
Keyword(s):  
Surface Roughness ◽  
Additive Manufacturing ◽  
Literature Review ◽  
Future Research ◽  
Reduction Potentials ◽  
Research Fields ◽  
Post Process ◽  
Accessibility Issues ◽  
End Use ◽  
And Performance

AbstractOne often-cited benefit of using metal additive manufacturing (AM) is the possibility to design and produce complex geometries that suit the required function and performance of end-use parts. In this context, laser powder bed fusion (LPBF) is one suitable AM process. Due to accessibility issues and cost-reduction potentials, such ‘complex’ LPBF parts should utilise net-shape manufacturing with minimal use of post-process machining. The inherent surface roughness of LPBF could, however, impede part performance, especially from a structural perspective and in particular regarding fatigue. Engineers must therefore understand the influence of surface roughness on part performance and how to consider it during design. This paper presents a systematic literature review of research related to LPBF surface roughness. In general, research focuses on the relationship between surface roughness and LPBF build parameters, material properties, or post-processing. Research on design support on how to consider surface roughness during design for AM is however scarce. Future research on such supports is therefore important given the effects of surface roughness highlighted in other research fields.

Sign in / Sign up

Export Citation Format

Share Document