scholarly journals Experimental and Numerical Evaluation of Mechanical Properties of 3D-Printed Stainless Steel 316L Lattice Structures

2021 ◽  
Author(s):  
M. Carraturo ◽  
G. Alaimo ◽  
S. Marconi ◽  
E. Negrello ◽  
E. Sgambitterra ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Mechanical Behavior ◽  
Numerical Simulations ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Lattice Structures ◽  
Stainless Steel 316L ◽  
Research Attention ◽  
Octet Truss

AbstractAdditive manufacturing (AM), and in particular selective laser melting (SLM) technology, allows to produce structural components made of lattice structures. These kinds of structures have received a lot of research attention over recent years due to their capacity to generate easy-to-manufacture and lightweight components with enhanced mechanical properties. Despite a large amount of work available in the literature, the prediction of the mechanical behavior of lattice structures is still an open issue for researchers. Numerical simulations can help to better understand the mechanical behavior of such a kind of structure without undergoing long and expensive experimental campaigns. In this work, we compare numerical and experimental results of a uniaxial tensile test for stainless steel 316L octet-truss lattice specimen. Numerical simulations are based on both the nominal as-designed geometry and the as-build geometry obtained through the analysis of µ-CT images. We find that the use of the as-build geometry is fundamental for an accurate prediction of the mechanical behavior of lattice structures.

LONG-TERM MECHANICAL BEHAVIOR OF A GREEN CEMENTITIOUS COMPOSITE

2015 ◽  
Vol 2 (1) ◽  
Author(s):  
H. Tian ◽  
Y. X. Zhang
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Mechanical Behavior ◽  
Building Materials ◽  
Weather Condition ◽  
Mechanical Tests ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Commercial Building

In this paper, a new green hybrid bagasse fiber (3% by volume) and steel fiber (0.7% by volume) reinforced cementitious composites with high volume fly ash (fly ash to cement ratio of 1.6) is developed and cured in weather condition up to 10 months. Basic mechanical tests, such as compressive test, Young’s modulus test, flexural test, and uniaxial tensile test and SEM tests were conducted at the age of 28 days, 3 months, 6 months and 10 months, respectively. Through comparison with the mechanical behavior of the composite at the age of 28 days, the long-term effect on the mechanical properties of the composite is evaluated. It is found the mechanical properties of the new composite increases greatly with aging. At the age of 10 months, the composite becomes more compacted and the composite is of excellent mechanical properties making it very promising to be used as commercial building materials.

Effect of Orientation on Mechanical Behavior of an Extruded Al Alloy

2008 ◽  
Author(s):  
M. A. Malik ◽  
I. Salam ◽  
W. Muhammad
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
Strain Rate ◽  
Mechanical Behavior ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Transverse Orientation ◽  
Longitudinal Orientation

The extruded materials are extensively used in chemical, food and nuclear industry and generally offer a unique combination of strength and freedom with regard to design solutions. During extrusion, material flow occurs in the direction of applied force and as a result microstructure change. The process ultimately induces variation in the mechanical properties when tested along or across the extrusion direction. The uniaxial tensile test is a simple and versatile test to expose most of the mechanical properties of the materials required to ensure the reliability of the systems. In present study, the mechanical behavior of an Al-Mg-Si alloy extruded cylinder has been determined with the help of uniaxial tensile test in longitudinal and transverse orientations. The microstructural features revealed significant difference in two orientations and constituent particles were found aligned in the direction of extrusion. Tensile tests were conducted in displacement mode at different cross head speeds corresponding to strain rates ranging from 10−5 to 10−1 s−1. The tests were conducted at ambient temperature in air atmosphere. The data thus obtained include: yield strength, ultimate tensile strength, percent elongation and reduction of area. Comparing the trends of strength variation, the material shows higher yield strength in longitudinal orientation as compared to transverse orientation. A slight increase in the yield strength with increasing strain rate was found in both the orientations. The ultimate tensile strength in both the directions was found similar and there was no appreciable change with increasing strain rate. The elongation and reduction in area were found higher in the longitudinal orientation. The effect of strain rate on these properties was negligible up to maximum speed tested. In longitudinal orientation typical dimpled fracture was observed indicating deformation before failure. In transverse orientation shallow dimples were present. The present study revealed that the distribution of constituent particles in an extruded thick-walled cylinder has a pronounced effect on its mechanical behavior and fracture morphology.

scholarly journals Effect of PWHT on the Microstructure and Mechanical Properties of Friction Stir Welded DP780 Steel

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1097
Author(s):  
Umer Masood Chaudry ◽  
Seung-Chang Han ◽  
Fathia Alkelae ◽  
Tea-Sung Jun
Keyword(s):  
Mechanical Properties ◽  
Annealing Temperature ◽  
Tensile Elongation ◽  
Image Correlation ◽  
Frictional Heat ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Friction Stir ◽  
Microstructure And Mechanical Properties ◽  
Dp780 Steel

In the present study, the effect of post-weld heat treatment (PWHT) on the microstructure and mechanical properties of friction stir welded (FSW) DP780 steel sheets was investigated. FSW was carried out at a constant tool rotation speed of 400 rpm and different welding speeds (200 mm/min and 400 min/min). A defect free weld was witnessed for both of the welding conditions. The mutual effect of severe plastic deformation and frictional heat generation by pin rotation during the FSW process resulted in grain refinement due to dynamic recrystallization in the stir zone (SZ) and thermo-mechanically affected zone (TMAZ). Lower tensile elongation and higher yield and ultimate tensile strengths were recorded for welded-samples as compared to the base material (BM) DP780 steel. The joints were subsequently annealed at various temperatures at 450–650 °C for 1 h. At higher annealing temperature, the work hardening rate of joints gradually decreased and subsequently failed in the softened heat-affected zone (HAZ) during the uniaxial tensile test. Reduction in yield strength and tensile strength was found in all PWHT conditions, though improvement in elongation was achieved by annealing at 550 °C. The digital image correlation analysis showed that an inhomogeneous strain distribution occurred in the FSWed samples, and the strain was particularly highly localized in the advancing side of interface zone. The nanoindentation measurements covering the FSWed joint were consistent with an increase of the annealing temperature. The various grains size in the BM, TMAZ, and SZ is the main factor monitoring the hardness distribution in these zones and the observed discrepancies in mechanical properties.

scholarly journals Influence of Microstructure on Mechanical Properties of Bainitic Steels in Railway Applications

Metals ◽  
2019 ◽  
Vol 9 (7) ◽  
pp. 778 ◽  
Author(s):  
Omid Hajizad ◽  
Ankit Kumar ◽  
Zili Li ◽  
Roumen H. Petrov ◽  
Jilt Sietsma ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Mechanical Behavior ◽  
Mechanical Performance ◽  
Electron Backscatter Diffraction ◽  
Bainitic Ferrite ◽  
Contact Fatigue ◽  
Rolling Contact ◽  
Uniaxial Tensile ◽  
Isothermal Heat Treatment

Wheel–rail contact creates high stresses in both rails and wheels, which can lead to different damage, such as plastic deformation, wear and rolling contact fatigue (RCF). It is important to use high-quality steels that are resistant to these damages. Mechanical properties and failure of steels are determined by various microstructural features, such as grain size, phase fraction, as well as spatial distribution and morphology of these phases in the microstructure. To quantify the mechanical behavior of bainitic rail steels, uniaxial tensile experiments and hardness measurements were performed. In order to characterize the influence of microstructure on the mechanical behavior, various microscopy techniques, such as light optical microscopy (LOM), scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD), were used. Three bainitic grades industrially known as B360, B1400 plus and Cr-Bainitic together with commonly used R350HT pearlitic grade were studied. Influence of isothermal bainitic heat treatment on the microstructure and mechanical properties of the bainitic grades was investigated and compared with B360, B1400 plus, Cr-Bainitic and R350HT in as-received (AR) condition from the industry. The results show that the carbide-free bainitic steel (B360) after an isothermal heat treatment offers the best mechanical performance among these steels due to a very fine, carbide-free bainitic microstructure consisting of bainitic ferrite and retained austenite laths.

Viscoplastic Constitutive Model for High Strain Rate Mechanical Properties of SAC-Q Leadfree Solder After High-Temperature Prolonged Storage

2018 ◽  
Author(s):  
Pradeep Lall ◽  
Vikas Yadav ◽  
Jeff Suhling ◽  
David Locker
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
High Strain Rate ◽  
Strain Rate ◽  
Thermal Aging ◽  
High Strain ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Aging Effects ◽  
Model Predictions

Electronics in automotive underhood and downhole drilling applications may be subjected to sustained operation at high temperature in addition to high strain-rate loads. SAC solders used for second level interconnects have been shown to experience degradation in high strain-rate mechanical properties under sustained exposure to high temperatures. Industry search for solutions for resisting the high-temperature degradation of SAC solders has focused on the addition of dopants to the alloy. In this study, a doped SAC solder called SAC-Q solder have been studied. The high strain rate mechanical properties of SAC-Q solder have been studied under elevated temperatures up to 200°C. Samples with thermal aging at 50°C for up to 6-months have been used for measurements in uniaxial tensile tests. Measurements for SAC-Q have been compared to SAC105 and SAC305 for identical test conditions and sample geometry. Data from the SAC-Q measurements has been fit to the Anand Viscoplasticity model. In order to assess the predictive power of the model, the computed Anand parameters have been used to simulate the uniaxial tensile test and the model predictions compared with experimental data. Model predictions show good correlation with experimental measurements. The presented approach extends the Anand Model to include thermal aging effects.

scholarly journals Microstructure and Mechanical Properties of 316L Stainless Steel Fabricated Using Selective Laser Melting

MRS Advances ◽  
2019 ◽  
Vol 4 (44-45) ◽  
pp. 2431-2439
Author(s):  
N. Iqbal ◽  
E. Jimenez-Melero ◽  
U. Ankalkhope ◽  
J. Lawrence
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Selective Laser Melting ◽  
Laser Scanning ◽  
316L Stainless Steel ◽  
Uniform Elongation ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Laser Melting ◽  
Sample Height

ABSTRACTThe microstructure homogeneity and variability in mechanical properties of 316L stainless steel components fabricated using selective laser melting (SLM) have been investigated. The crack free, 99.9% dense samples were made starting from SS316L alloy powder, and the melt pool morphology was analysed using optical and scanning electron microscopy. Extremely fast cooling rates after laser melting/solidification process, accompanied by slow diffusion of alloying elements, produced characteristic microstructures with colonies of cellular substructure inside grains, grown along the direction of the principal thermal gradient during laser scanning. In some areas of the microstructure, a significant number of precipitates were observed inside grains and at grain boundaries. Micro hardness measurements along the build direction revealed slight but gradual increase in hardness along the sample height. Uniaxial tensile tests of as manufactured samples showed the effect of un-melted areas causing scatter in room-temperature mechanical properties of samples extracted from the same SLM build. The ultimate tensile strength (UTS) varied from 458MPa to 509MPa along with a variation in uniform elongation from 3.3% to 14.4%. The UTS of a sample exposed to the Cl- rich corrosion environment at 46oC temperature revealed a similar strength as of the original sample, indicating good corrosion resistance of SLM samples under those corrosion conditions.

scholarly journals The Influence of Sub-Zero Conditions on the Mechanical Properties of Polylactide-Based Composites

Materials ◽  
2020 ◽  
Vol 13 (24) ◽  
pp. 5789
Author(s):  
Olga Mysiukiewicz ◽  
Mateusz Barczewski ◽  
Arkadiusz Kloziński
Keyword(s):  
Mechanical Properties ◽  
Room Temperature ◽  
Mechanical Performance ◽  
Mechanical Analysis ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Mechanical And Thermal Properties ◽  
Scanning Calorimetry ◽  
Linseed Cake ◽  
Static Mechanical

Polylactide-based composites filled with waste fillers due to their sustainability are a subject of many current papers, in which their structural, mechanical, and thermal properties are evaluated. However, few studies focus on their behavior in low temperatures. In this paper, dynamic and quasi-static mechanical properties of polylactide-based composites filled with 10 wt% of linseed cake (a by-product of mechanical oil extraction from linseed) were evaluated at room temperature and at −40 °C by means of dynamic mechanical analysis (DMA), Charpy’s impact strength test and uniaxial tensile test. It was found that the effect of plasticization provided by the oil contained in the filler at room temperature is significantly reduced in sub-zero conditions due to solidification of the oil around −18 °C, as it was shown by differential scanning calorimetry (DSC) and DMA, but the overall mechanical performance of the polylactide-based composites was sufficient to enable their use in low-temperature applications.

Characterization and Evaluation of Mechanical Properties and Residual Stress in Aluminum-Magnesium Alloys Welded by the FSW Process

2020 ◽  
Vol 1012 ◽  
pp. 349-353
Author(s):  
D.B. Colaço ◽  
M.A. Ribeiro ◽  
T.M. Maciel ◽  
R.H.F. de Melo
Keyword(s):  
Mechanical Properties ◽  
Residual Stress ◽  
Residual Stresses ◽  
Welding Process ◽  
Bending Test ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Friction Stir ◽  
Aluminum Magnesium Alloys

The demand for lighter materials with suitable mechanical properties and a high resistance to corrosion has been increasing in the industries. Therefore, aluminum appears as an alternative due to its set of properties. The aim of this work was to evaluate residual stress levels and mechanical properties of welded joints of Aluminum-Magnesium alloy AA 5083-O using the Friction Stir Welding process. For mechanical characterization were performed a uniaxial tensile test, Vickers hardness, bending test and, finally, the determination of residual stresses. It was concluded that welding by FSW process with an angle of inclination of the tool at 3o, established better results due to better mixing of materials. The best results of tensile strength and a lower level of residual stresses were obtained using a tool rotation speed of 340 RPM with welding advance speed of 180 mm/min and 70 mm/min.

Sign in / Sign up

Export Citation Format

Share Document