Full Integration of SCADA, Field Control Systems and High Speed Hydraulic Models: Application Pacific Pipeline System

2000 ◽  
Author(s):  
Travis Mecham ◽  
Bruce Wilkerson ◽  
Bryan Templeton
Keyword(s):  
Control System ◽  
Environmental Impact ◽  
Control Systems ◽  
Fiber Optic ◽  
Detection System ◽  
Leak Detection ◽  
Pipeline System ◽  
Scada System ◽  
Fiber Optic Communication ◽  
Optic Communication

Recent advances in PLC, SCADA and leak detection system technologies lead to the development of a highly integrated control system. Interconnected with fiber optic communication speeds (OC-1), this level of integration moves away from the historic model of stand-alone field controllers connected over low speed communication links to a centralized control center which, in turn, exchanges data from the host system to stand-alone leak detection processors. A new system design approach utilized familiar pipeline control elements such as PLC controllers and MODBUS communication protocols in combination with elements more typically associated with an office environment such as Windows NT servers, PC compatible computers, and Ethernet TCP/IP communications networks. These open-architecture components were used to fully develop, debug and test the SCADA system prior to system startup. The pipeline simulator is used as the centerpiece for this process to perform thorough operational validation of the system long before initial linefill. Once the various components were fully tested they were exported to the physical system in an operational state. The result is nearly seamless control systems supported by high data rates, high model speeds, common databases, and multi-channel communications. The increased level of integration has had dramatic impacts in leak detection, system safety, engineering development, operator training, and overall reliability of the control systems. The following paper presents a narrative overview of these new developments in the context of an implementation on Pacific Pipeline System (PPS). PPS is a recently constructed and commissioned 209 km (130 mile), 50.8 cm (20″) diameter, hot crude oil pipeline between the southern portion of California’s San Joaquin Valley and refineries in the Los Angeles basin. Following the Interstate 5 corridor over the “Grapevine”, Tejon Pass, Angeles National Forest and through heavily populated areas, this pipeline traverses some of the most environmentally and safety sensitive regions in the United States. The joint federal and state Environmental Impact Report / Environmental Impact Statement (EIR/EIS) set high hurdles for leak detection and control system performance. The historic control architecture and technologies were not adequate. This paper provides an overview of the environmental and physical constraints of the Pacific Pipeline System alignment, hydraulics, pumping and metering equipment, and block valve locations. It also discusses their impact on the design, programming and commissioning of a SCADA system meeting the requirements of the EIR/EIS. The paper then describes in more detail the fiber-optic communication system, control system architecture, SCADA system, leak detection models, simulator models and implementation methods, along with the engineering decisions leading to a comprehensive solution for the SCADA and leak detection requirements.

scholarly journals New high-speed system for controlling the parameters of a nuclear reactor in a nuclear power plant

2019 ◽  
Vol 140 ◽  
pp. 02001 ◽  
Author(s):  
Roman Davydov ◽  
Valery Antonov ◽  
Sergey Makeev ◽  
Yury Batov ◽  
Valentin Dudkin ◽  
...  
Keyword(s):  
Power Plant ◽  
Nuclear Power Plant ◽  
Control Systems ◽  
High Speed ◽  
Nuclear Power ◽  
Nuclear Reactor ◽  
Fiber Optic ◽  
Fiber Optic Communication ◽  
Optic Communication ◽  
Communication Lines

The necessity of modernizing current control systems for functional units of a nuclear power plant, as well as the development of new control systems with a high degree of reliability and speed, is substantiated. The advantages of using optical sensors and fiber-optic communication lines to solve these problems are noted. Cases for which it is necessary to develop new fiber-optic sensors for monitoring parameters, for example, the flow of coolant or feed water, are considered. In some of them, it is more expedient to use standard designs of fiber-optic sensors to control the operating parameters of various blocks, for example, to control the electric field strength. A device and a control scheme for the parameters of the units and systems of a nuclear power plant using fiber-optic communication lines have been developed. The results of measuring various parameters of a nuclear reactor are presented. They showed that our proposed fiber-optic control and monitoring system for nuclear power plants operates more reliably and efficiently than systems with analogue control and measurement channels. The use of fiber-optic systems allows real-time remote control and high-speed control in terms of issuing commands to devices. This is very important when servicing a nuclear power plant while it is operating in extreme conditions.

scholarly journals Time Domain Equalization and Digital Back-Propagation Method-Based Receiver for Fiber Optic Communication Systems

2020 ◽  
Vol 2020 ◽  
pp. 1-13 ◽  
Author(s):  
Fazal Muhammad ◽  
Farman Ali ◽  
Usman Habib ◽  
Muhammad Usman ◽  
Imran Khan ◽  
...  
Keyword(s):  
Optical Fiber ◽  
Spectral Efficiency ◽  
Communication Systems ◽  
High Speed ◽  
Fiber Optic ◽  
Detection System ◽  
Data Rate ◽  
Modulation Formats ◽  
Fiber Optic Communication ◽  
Optic Communication

Fiber optic communication systems (FOCSs) have attained a lot of attention by revolutionizing the telecommunication industry and offering new possibilities with the technical advancements in state-of-the-art high speed digital electronics. Advanced modulation formats make use of the phase, amplitude, and polarization of the optical signals at the same time to provide high spectral efficiency as compared with 1 bit/s/Hz for the intensity modulation direct detection system (IMDD), but are highly prone to transmission impairments. Thus, the effects that add up to the optical fiber impairments such as optical fiber chromatic dispersion (OFCD), polarization model dispersion (PMD), and phase offset and noise (POaN) need to be addressed at the receiver side. The development of components and algorithms to minimize these effects in next generation FOCSs with 100 Gbps data rate and beyond with long-haul transmission is still a challenging issue. In this paper, digital signal processing- (DSP-) assisted dispersion and nonlinear compensation techniques are presented to compensate for physical layer impairments including OFCD, PMD, and POaN. The simulations are performed considering Dual Polarization- (DP-) QPSK modulation format to achieve two-fold data rate to achieve spectral efficiency of 3.28 bits/s/Hz by making use of the polarization diversity and system performance is investigated in terms of bit error rate (BER), constellation diagrams, and quality factor (Q-factor) for different values of optical signal-to-noise ratio (OSNR), launch power (PL), and fiber length.

Optical data signals in fiber optic communication links with fading

2019 ◽  
pp. 94-104
Author(s):  
I. Juwiler ◽  
I. Bronfman ◽  
N. Blaunstein
Keyword(s):  
Spectral Efficiency ◽  
Fiber Optic ◽  
Fiber Optic Cable ◽  
Optical Signals ◽  
Dispersion Properties ◽  
Optical Cable ◽  
Time Dispersion ◽  
Communication Links ◽  
Fiber Optic Communication ◽  
Optic Communication

Introduction: This article is based on the recent research work in the field of two subjects: signal data parameters in fiber optic communication links, and dispersive properties of optical signals caused by non-homogeneous material phenomena and multimode propagation of optical signals in such kinds of wired links.Purpose: Studying multimode dispersion by analyzing the propagation of guiding optical waves along a fiber optic cable with various refractive index profiles of the inner optical cable (core) relative to the outer cladding, as well as dispersion properties of a fiber optic cable due to inhomogeneous nature of the cladding along the cable, for two types of signal code sequences transmitted via the cable: return-to-zero and non-return-to-zero ones.Methods: Dispersion properties of multimode propagation inside a fiber optic cable are analyzed with an advanced 3D model of optical wave propagation in a given guiding structure. The effects of multimodal dispersion and material dispersion causing the optical signal delay spread along the cable were investigated analytically and numerically.Results: Time dispersion properties were obtained and graphically illustrated for two kinds of fiber optic structures with different refractive index profiles. The dispersion was caused by multimode (e.g. multi-ray) propagation and by the inhomogeneous nature of the material along the cable. Their effect on the capacity and spectral efficiency of a data signal stream passing through such a guiding optical structure is illustrated for arbitrary refractive indices of the inner (core) and outer (cladding) elements of the optical cable. A new methodology is introduced for finding and evaluating the effects of time dispersion of optical signals propagating in fiber optic structures of various kinds. An algorithm is proposed for estimating the spectral efficiency loss measured in bits per second per Hertz per each kilometer along the cable, for arbitrary presentation of the code signals in the data stream, non-return-to zero or return-to-zero ones. All practical tests are illustrated by MATLAB utility.

MODELING OF FIBER-OPTIC COMMUNICATION CHANNEL FOR QUANTUM CRYPTOGRAPHIC SYSTEMS

2019 ◽  
pp. 90-95
Author(s):  
V. A. Minaev ◽  
I. D. Korolev ◽  
O. A. Kulish ◽  
A. V. Mazin
Keyword(s):  
Information Transmission ◽  
Information Transfer ◽  
Fiber Optic ◽  
Single Photon ◽  
Optical Devices ◽  
Energy Losses ◽  
Integrated Optical ◽  
Integrated Optical Devices ◽  
Fiber Optic Communication ◽  
Optic Communication

The existing methods of information delivery to the strategic and tactical management of many government agencies are expensive, not always reliable and efficient. Therefore, quantum cryptographic systems (QCS) have been actively developed in recent years. However, there are problems with the use of the QCS associated with the reliability of information transfer. First, the existing fiber-optic communication channels (FOCC) are not designed to transmit single-photon signals, which leads to the complexity of their cryptographic protection. The second is insufficiently methodically developed calculation of energy losses and errors in the evaluation of the characteristics of information transfer in FOCC QCS. In article the analysis of the energy loss factors in the classical fiber-optic channel is carried out and the additive loss formula is discussed in detail. Then we consider the fiber-optic channel of quantum information transmission with the use of integrated optical devices. The additive formula of optical losses in such a channel is discussed. The features of losses in integrated optical devices are shown. The features of quantum cryptographic system of information transmission are considered. As a result, the model of FOCC QCS taking into account energy losses is presented, which allows competently in theoretical terms and visualize the passage of information through modern quantum cryptographically secure telecommunications while providing control in government structures.

Tributary Mapping Multiplexing an Efficient Technique for High Speed Fiber Optic Communication

2018 ◽  
Vol 6 (2) ◽  
Author(s):  
Usman Illahi ◽  
Javed Iqbal ◽  
Muhammad Ismail Sulaiman ◽  
Muhammad Alam ◽  
Mazliham Mohd Su'ud
Keyword(s):  
Spectral Efficiency ◽  
High Speed ◽  
Fiber Optic ◽  
Single Channel ◽  
Efficient Technique ◽  
High Dispersion ◽  
Optical Filtering ◽  
Fiber Optic Communication ◽  
Optic Communication ◽  
Dispersion Tolerance

<p>A novel technique of multiplexing called Tributary Mapping Multiplexing (TMM) is<br />applied to a single channel wavelength division multiplexing system and performance is monitored on the basis of simulation results. To elaborate the performance of TMM in this paper, a 4-User TMM system over single wavelength channel is demonstrated. TMM showed significant tolerance against narrow optical filtering as compared to that of conventional TDM at the rate of 40 Gbit/s. The above calculations are made by optical filter bandwidth and dispersion tolerance that was allowed at minimum. The spectral efficiency achieved by this TMM was 1 b/s/Hz and it was executed by using transmitters and receivers of 10 Gbit/s without polarized multiplexing. The high spectral efficiency, high dispersion tolerance and tolerance against strong optical filtering makes TMM an efficient technique for High<br />Speed Fiber Optic Communication.</p>

Sign in / Sign up

Export Citation Format

Share Document