Three Dimensional Finite Element Analysis of Staggered Backward Flow Forming Process

2013 ◽  
Author(s):  
Hemant Shinde ◽  
Pushkar Mahajan ◽  
Ramesh Singh ◽  
K. Narasimhan
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Process Conditions ◽  
State Variables ◽  
Forming Process ◽  
Flow Forming ◽  
Element Analysis ◽  
Cold Forming ◽  
Cylindrical Workpiece ◽  
Backward Flow Forming

Flow forming is one of the cold forming processes which is mainly used to produce thin-walled high-precision tubular components. A three dimensional coupled-field thermo-mechanical finite element model for staggered three-roller backward flow forming of a cylindrical workpiece of MDN-250 maraging steel has been developed using Abaqus/Explicit. In this model, the effect of tip radius of the rollers and friction between the rollers and the workpiece has been considered. The bottom of the workpiece is fixed in the axial direction so that diametral reduction and the axial elongation can be studied. Simulations have been carried out at different process conditions to study the state variables, such as stresses and strains obtained during the deformation. The model has been benchmarked with the experimental results for thickness reduction and the error in the thickness prediction is limited to 4%. The roll forces have been benchmarked against analytical formulation and a difference of 13–20% has been observed. The effect of flow forming process variables, such as feed rate and reduction ratio on the stress/strain distribution and roll forces have been studied. The results show that the roll forces increase at higher feed rates and higher reduction ratios whereas the equivalent strains increase at lower feed rates and higher reduction ratios. In addition, a parametric study has been conducted to study ovality, diametral growth, roll forces, stresses and strains as a function of process parameters.

Nonlinear Finite Element Analysis of Spring-Back Characteristics in the Cold-Forming Process of Three-Dimensionally Curved Thick Metal Plates

2013 ◽  
Vol 135 (3) ◽  
Author(s):  
Jeom Kee Paik ◽  
Jeong Hwan Kim ◽  
Bong Ju Kim ◽  
Chang Hyo Tak
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Steel Plates ◽  
Research Centre ◽  
Spring Back ◽  
Forming Process ◽  
Element Analysis ◽  
Cold Forming ◽  
Metal Plates ◽  
National University

The present paper is part of the study to develop the advanced computer aided manufacture (CAM) system called the changeable die system (CDS) that applies the cold-forming technique to produce curved thick metal plates with complex, three-dimensional geometry [Paik et al., 2009, “Development of the Changeable Die System for the Cold-Forming of Three-Dimensionally Curved Metal Plates,” The Lloyd's Register Educational Trust Research Centre of Excellence, Pusan National University, Korea]. This paper focuses on the procedure of predicting the spring-back characteristics using elastic-plastic large deflection finite element method, which is a key technical element within the framework of the CDS process. The validity of the procedure is confirmed by comparison with experimental results obtained by the CDS machine in the cold-forming process of curved steel plates.

Progressive failure analysis of scarf-repaired composite laminate based on damage constitutive model

2016 ◽  
Vol 233 (2) ◽  
pp. 180-188 ◽  
Author(s):  
Qiuyi Shen ◽  
Zhenghao Zhu ◽  
Yi Liu
Keyword(s):  
Finite Element ◽  
Constitutive Model ◽  
Composite Laminate ◽  
Damage Mechanics ◽  
Cohesive Zone Model ◽  
Load Capacity ◽  
Three Dimensional ◽  
Zone Model ◽  
State Variables ◽  
Element Analysis

A three-dimensional finite element model for scarf-repaired composite laminate was established on continuum damage model to predict the load capacity under tensile loading. The mixed-mode cohesive zone model was adopted to the debonding behavior analysis of adhesive. Damage condition and failure of laminates and adhesive were subsequently addressed. A three-dimensional bilinear constitutive model was developed for composite materials based on damage mechanics and applied to damage evolution and loading capacity analyses by quantifying damage level through damage state variables. The numerical analyses were implemented with ABAQUS finite element analysis by coding the constitutive model into material subroutine VUMAT. Good agreement between the numerical and experimental results shows the accuracy and adaptability of the model.

Concurrent Engineering Design of Sheet Stamping by Using an Inverse FE Approach

1997 ◽  
Author(s):  
Shiyong Yang ◽  
Kikuo Nezu
Keyword(s):  
Finite Element ◽  
Concurrent Engineering ◽  
Process Simulation ◽  
Three Dimensional ◽  
Sheet Forming ◽  
Design Stage ◽  
Forming Process ◽  
Element Analysis ◽  
Preliminary Design Stage ◽  
Product And Process

Abstract An inverse finite element (FE) algorithm is proposed for sheet forming process simulation. With the inverse finite element analysis (FEA) program developed, a new method for concurrent engineering (CE) design for sheet metal forming product and process is proposed. After the product geometry is defined by using parametric patches, the input models for process simulation can be created without the necessity to define the initial blank and the geometry of tools, thus simplifying the design process and facilitating the designer to look into the formability and quality of the product being designed at preliminary design stage. With resort to a commercially available software, P3/PATRAN, arbitrarily three-dimensional product can be designed for manufacturability for sheet forming process by following the procedures given.

Finite Element Analysis of Load Capacity on Coupling Clamps for Pipe

2012 ◽  
Vol 201-202 ◽  
pp. 741-744 ◽  
Author(s):  
Zhen Ning Hou ◽  
Jun Wu ◽  
Qing Wang ◽  
Hong Gen Tian ◽  
Nan Chao ◽  
...  
Keyword(s):  
Finite Element ◽  
Stress Intensity ◽  
Optimization Design ◽  
Load Capacity ◽  
Three Dimensional ◽  
Process Conditions ◽  
Fe Model ◽  
Three Dimensional Model ◽  
Element Analysis ◽  
Element Approach

A finite element approach based on Ansys is developed to simulate stress intensity distribution in a three dimensional model of coupling clamp joint, which includes ferrules, pipe caps and bolts. The characteristics of stress intensity distributions of coupling clamp joint under strength pressure loading have been studied by means of the non-linear finite element method. The FE model can also predict the clamp quality and tolerances to be expected under different process conditions and define the most effective process parameters to influence the tolerances. The study could give us a better understanding on the mechanism and basis for optimization design of the coupling clamp joint.

An Elasto-Plastic Finite Element Analysis of the Hat-Type Drawing Process of Sheet Metal

2006 ◽  
Vol 505-507 ◽  
pp. 709-714
Author(s):  
Tsung Chia Chen ◽  
You Min Huang
Keyword(s):  
Finite Element ◽  
Sheet Metal ◽  
Moving Boundary ◽  
Contact Problems ◽  
Computer Code ◽  
Plastic State ◽  
Process Conditions ◽  
Drawing Process ◽  
Forming Process ◽  
Element Analysis

This study aims to clarify the process conditions of the hat-type drawing of a sheet metal of steel. It provides a model that predicts not only the correct punch load for drawing, but also the precise final shape of products after unloading, based on the tensile properties of the material and the geometry of the tools used. An elasto-plastic incremental finite-element computer code, based on an updated Lagrangian formulation, was developed to simulate the hat-type drawing of sheet metal. In particular, selective reduced integration was adopted to formulate the stiffness matrix. The extended r-minimum technique was used to deal with the elasto-plastic state and contact problems at the tool-metal interface. A series of simulations were performed to validate the formulation in the theory, leading to the development of the computer codes. The whole deformation history and the distribution of stress and strain during the forming process were obtained by carefully considering the moving boundary condition in the finite-element method. Results in this study clearly demonstrated that the computer code for simulating the hat-type drawing process was efficient.

Three-Dimensional Elastic-Plastic Finite-Element Analysis of the Flattening of Wire Between Plain Rolls*

2000 ◽  
Vol 123 (3) ◽  
pp. 397-404 ◽  
Author(s):  
H. Utsunomiya ◽  
P. Hartley ◽  
I. Pillinger
Keyword(s):  
Finite Element ◽  
Elastic Recovery ◽  
Three Dimensional ◽  
Lateral Spread ◽  
Radius Of Curvature ◽  
Forming Process ◽  
Empirical Formulas ◽  
Element Analysis ◽  
Finite Element Program ◽  
Elastic Plastic

It is normal industrial practice to roll round edged flat wires from round circular wires using plain rolls. Although this is not a complex type of metal forming process, the internal deformation is highly three-dimensional. It is important to be able to determine the lateral spread, elongation and final profile precisely. In this paper, this process has been analyzed using an elastic-plastic finite element program. Firstly, algorithms for integrating the constitutive equations, i.e., return mapping algorithms, are evaluated to determine the most accurate technique. Then, the influences of friction and reduction in thickness on the deformation characteristics are investigated. The lateral spread and the radius of curvature of the free surface are quantitatively in reasonable agreement with those obtained from empirical formulas. The lateral spread increases with friction and with reduction. The variation of elongation in the roll bite is investigated in detail. It is found that the elongation is not uniformly distributed across the cross section. After passing the roll gap, the distribution is compensated by the elastic recovery of wire, otherwise it may cause edge waves.

Elastic-Plastic Finite Element Simulation of Bulge Forming Process Using a Variable Cross-Section Solid Bulging Mold

2011 ◽  
Vol 189-193 ◽  
pp. 4405-4408
Author(s):  
Ke Wang ◽  
Zhe Ying Wang ◽  
Xing Wei Sun
Keyword(s):  
Finite Element ◽  
Cross Section ◽  
Metal Flow ◽  
Three Dimensional ◽  
Variable Cross Section ◽  
Flow Mode ◽  
Variable Cross ◽  
Forming Process ◽  
Element Analysis ◽  
Screw Rotor

Bulge forming is a novel process aimed at common products including T-branches, cross branches and angle branches. But bulging forming has not applied for two-head abnormity-shaped hollow screw rotor reported in literature. Simulation of the bulging forming of two-head abnormity-shaped hollow screw rotor has not been reported. This paper presents a simulation of the bulge forming process of two-head abnormity-shaped hollow screw rotor using a variable cross-section solid bulging mold. Some conditions including the effect of friction, boundary conditions, contact conditions and the space motion, etc are presented. The mathematical model of three-dimensional finite element analysis has been established. The distribution of generalized plastic strain and general metal flow mode in cross section of two abnormity-shaped hollow screw rotor has been analyzed. It is an effective method for the analysis of other defects and the optimization of process parameters further.

scholarly journals Investigating of Mechanical Behavior of AA5083 in the Pressing Process Using Finite Element Analysis

2017 ◽  
Vol 11 (9) ◽  
pp. 51
Author(s):  
Babak Beglarzadeh ◽  
Behnam Davoodi
Keyword(s):  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Aluminum Alloy ◽  
Friction Stress ◽  
Forming Process ◽  
Element Analysis ◽  
Cold Forming ◽  
Aluminum Alloy 5083 ◽  
And Control

The process of cold forming is considered of the most different industries and the use of such process in the manufacture of components and small parts has expanded. Therefore, analyzing the behavior of metals in this process to identify and control durability that is the main factor of limiting process has particular importance in industrial forming processes. In this study, cold forming process of aluminum metal has been studied and its effect on its mechanical properties has been evaluated. For this purpose, first modeling piece of aluminum alloy 5083 for cold forming process is carried out and using finite element analysis, mechanical properties of considered piece during cold forming processes are investigated. The results show that by reducing friction, stress and strain during the process will reduce, thereby durability of the piece increases, or in other words, ductile fracture occurs in longer life and higher stresses. The results show that by proper forming operations, it can be improved the strength and durability of aluminum alloy. Finally, validation of results, by comparing simulation results with experimental results is carried out.

scholarly journals Finite Element Analysis of Extrusion Process for Magnesium Alloy Internal Threads with Electromagnetic Induction-Assisted Heating and Thread Performance Research

Materials ◽  
2020 ◽  
Vol 13 (9) ◽  
pp. 2170 ◽  
Author(s):  
Meng Liu ◽  
Zesheng Ji ◽  
Rui Fan ◽  
Xingguo Wang
Keyword(s):  
Finite Element ◽  
Magnesium Alloy ◽  
Electromagnetic Induction ◽  
High Speed ◽  
Heating Temperature ◽  
Equivalent Stress ◽  
Hole Diameter ◽  
Process Conditions ◽  
Forming Process ◽  
Element Analysis

The casting magnesium alloy AZ91D cannot be extruded at room temperature. This paper presents a process for extruding internal threads using AZ91D heated by electromagnetic induction. The feasibility of the process is verified by finite element simulation and experiments. Using DEFORM-3D to simulate the process of extruding a M12 × 1.25 mm threaded hole by electromagnetic induction-assisted heating, the equivalent stress-strain and material flow law in the process of thread deformation was analyzed and verified by experiments. Three parameters—hole diameter, machine speed and heating temperature—were considered to study the influence of different process conditions on the forming torque. The results show that a heating temperature above 523 K can improve the plasticity of AZ91D. The hole diameter has an important influence on the forming torque. The forming process is not suitable for high-speed machining. The surface metal of the thread formed by this process has a strong deformation layer, which can improve the strength and hardness of the thread.

Sign in / Sign up

Export Citation Format

Share Document