Analysis of the Fatigue Damage on the Offshore Wind Turbines Exposed to Wind and Wave Loads Within the Typhoon Area

2004 ◽  
Author(s):  
Atsushi Yamashita ◽  
Kinji Sekita
Keyword(s):  
Fatigue Damage ◽  
Wind Turbines ◽  
Offshore Wind ◽  
Wave Loads ◽  
Wave Load ◽  
Offshore Wind Turbines ◽  
Simple Addition ◽  
Recorded Data ◽  
Term Data

For the design of offshore wind turbines exposed to wind and wave loads, the method of combining the wind load and the wave load is significantly important to properly calculate the maximum stresses and deflections of the towers and the foundations1). Similarly, for the analysis of the fatigue damage critical to the structural life, the influences of combined wind and wave loads have not been clearly verified. In this paper fatigue damage at the time of typhoon passing is analyzed using actually recorded data, though intrinsically long-term data more than 10years should be used to properly evaluate the fatigue damage. This paper concludes that the fatigue damage of the tower caused by the wave load is not substantial and, thus, the fatigue damage by the combined wind and wave load is only 2–3% larger than the simple addition of the independent fatigue damages by the wind and the wave loads. The fatigue damage of the tower top, which is required to reduce the diameter in order to minimize the aerodynamic confliction with blades, is larger than that of the tower bottom. The fatigue damage at the foundation by the combined wind and wave load is 25% larger than the simple addition of the wind and wave damages, as the foundation is directly exposed to the wave load. For the foundation, the proper structural section can be designed in order to improve the structural performance against fatigue.

Soil–Structure–Wave Interaction of Gravity-Based Offshore Wind Turbines: An Analytical Model

2020 ◽  
Vol 143 (3) ◽  
Author(s):  
Dimitrios G. Pavlou
Keyword(s):  
Dynamic Response ◽  
Analytical Model ◽  
Wind Turbines ◽  
Initial Conditions ◽  
Offshore Wind ◽  
Design Parameters ◽  
Wave Loads ◽  
Wave Load ◽  
Offshore Wind Turbines ◽  
Dynamic Phenomena

Abstract The structural design of offshore wind turbines is based on the consideration of coupled dynamic phenomena. Wave loads cause the dynamic oscillation of the monopile, and the dynamic oscillation of the monopile affects the wave loads. The boundary conditions of the gravity-based foundation-monopile-turbine system are mostly affected by the flexural stiffness of the foundation plate, the elastic and creep behavior of the soil, and the inertia (translational and rotational) of the wind turbine mass. The design of the foundation should consider the dynamic response of the soil and the monopile, and the dynamic response of the soil and the monopile is affected by the design parameters of the foundation. The initial conditions of the system yield transient dynamic phenomena. A braking wave at t = 0 causes different dynamic response than the steady-state conditions due to a harmonic wave load. In the present work, an integrated analytical model simulating the above dynamic phenomena is proposed. With the aid of double integral transforms and generalized function properties, a solution of the corresponding differential equations for the monopile-soil-foundation system and the boundary and initial conditions is derived. A parametric study is carried out, and results of the effect of the design parameters and soil properties are presented and discussed.

Implied Reliability Levels in Different Load Models for Offshore Wind Turbines

2014 ◽  
Author(s):  
P. Agarwal ◽  
L. Manuel
Keyword(s):  
Wind Turbines ◽  
Large Diameter ◽  
Offshore Wind ◽  
International Electrotechnical Commission ◽  
Wave Loads ◽  
Support Structures ◽  
Wave Load ◽  
Load Effect ◽  
Offshore Wind Turbines ◽  
Inertia Forces

Assuring uniform reliability levels across various system configurations is the intent of design standards based on the Load and Resistance Factor Design (LRFD) methodology. One such design standard for offshore wind turbines developed by the International Electrotechnical Commission was based on the European experience and may not necessarily represent conditions suited for U.S. waters where several offshore wind energy projects are being planned. It is, hence, of interest to investigate how uniform is the reliability of offshore wind turbines under various levels of wind and wave loads. We assess the reliability of bottom-supported offshore wind turbines in ultimate limit states associated with the fore-aft tower bending moment at the mudline. We compare reliability index estimates for different characteristic load definitions and assumed coefficients of variation for wind and wave loads, as well as for various hydrodynamic to aerodynamic load influences. Effectively, such variations serve to describe different sites and turbine designs. Since large-diameter monopile support structures are dominated by inertia forces, while jacket or tripod support structures with smaller diameter members are dominated by drag forces, we extend an available combined wind-wave load effect model for offshore wind turbines, to include both drag and inertia forces. We show that reasonably uniform reliability levels may be achieved for various combinations of wind and wave loads. Results suggest that drag-dominated wave load cases result in smaller and less uniform reliability estimates than is the case for inertia-dominated wave load cases.

Comparison of Spar and Semisubmersible Floater Concepts of Offshore Wind Turbines Using Long-Term Analysis

2015 ◽  
Vol 137 (6) ◽  
Author(s):  
Hasan Bagbanci ◽  
D. Karmakar ◽  
C. Guedes Soares
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Transfer Functions ◽  
Probability Distributions ◽  
Offshore Wind ◽  
Short Term ◽  
Offshore Wind Turbines ◽  
Floating Wind Turbine ◽  
Offshore Floating Wind Turbine

The long-term probability distributions of a spar-type and a semisubmersible-type offshore floating wind turbine response are calculated for surge, heave, and pitch motions along with the side-to-side, fore–aft, and yaw tower base bending moments. The transfer functions for surge, heave, and pitch motions for both spar-type and semisubmersible-type floaters are obtained using the fast code and the results are also compared with the results obtained in an experimental study. The long-term predictions of the most probable maximum values of motion amplitudes are used for design purposes, so as to guarantee the safety of the floating wind turbines against overturning in high waves and wind speed. The long-term distribution is carried out using North Atlantic wave data and the short-term floating wind turbine responses are represented using Rayleigh distributions. The transfer functions are used in the procedure to calculate the variances of the short-term responses. The results obtained for both spar-type and semisubmersible-type offshore floating wind turbine are compared, and the study will be helpful in the assessments of the long-term availability and economic performance of the spar-type and semisubmersible-type offshore floating wind turbine.

scholarly journals The Effect of the Second-Order Wave Loads on Drift Motion of a Semi-Submersible Floating Offshore Wind Turbine

2020 ◽  
Vol 8 (11) ◽  
pp. 859
Author(s):  
Thanh-Dam Pham ◽  
Hyunkyoung Shin
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Second Order ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Wave Loads ◽  
Hydrodynamic Loads ◽  
Drift Motion ◽  
Offshore Wind Turbines ◽  
Floating Offshore Wind Turbines

Floating offshore wind turbines (FOWTs) have been installed in Europe and Japan with relatively modern technology. The installation of floating wind farms in deep water is recommended because the wind speed is stronger and more stable. The design of the FOWT must ensure it is able to withstand complex environmental conditions including wind, wave, current, and performance of the wind turbine. It needs simulation tools with fully integrated hydrodynamic-servo-elastic modeling capabilities for the floating offshore wind turbines. Most of the numerical simulation approaches consider only first-order hydrodynamic loads; however, the second-order hydrodynamic loads have an effect on a floating platform which is moored by a catenary mooring system. At the difference-frequencies of the incident wave components, the drift motion of a FOWT system is able to have large oscillation around its natural frequency. This paper presents the effects of second-order wave loads to the drift motion of a semi-submersible type. This work also aimed to validate the hydrodynamic model of Ulsan University (UOU) in-house codes through numerical simulations and model tests. The NREL FAST code was used for the fully coupled simulation, and in-house codes of UOU generates hydrodynamic coefficients as the input for the FAST code. The model test was performed in the water tank of UOU.

On the Modeling of Nonlinear Waves for Prediction of Long-Term Offshore Wind Turbine Loads

2008 ◽  
Author(s):  
P. Agarwal ◽  
L. Manuel
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Return Period ◽  
Wave Model ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Offshore Wind Turbines ◽  
Irregular Wave ◽  
Inflow Turbulence

In the design of wind turbines—onshore or offshore—the prediction of extreme loads associated with a target return period requires statistical extrapolation from available loads data. The data required for such extrapolation are obtained by stochastic time-domain simulation of the inflow turbulence, the incident waves, and the turbine response. Prediction of accurate loads depends on assumptions made in the simulation models employed. While for the wind, inflow turbulence models are relatively well established, for wave input, the current practice is to model irregular (random) waves using a linear wave theory. Such a wave model does not adequately represent waves in shallow waters where most offshore wind turbines are being sited. As an alternative to this less realistic wave model, the present study investigates the use of irregular nonlinear (second-order) waves for estimating loads on an offshore wind turbine, with a focus on the fore-aft tower bending moment at the mudline. We use a 5MW utility-scale wind turbine model for the simulations. Using, first, simpler linear irregular wave modeling assumptions, we establish long-term loads and identify governing environmental conditions (i.e., the wind speed and wave height) that are associated with the 20-year return period load derived using the inverse first-order reliability method. We present the nonlinear irregular wave model next and incorporate it into an integrated wind-wave-response simulation analysis program for offshore wind turbines. We compute turbine loads for the governing environmental conditions identified with the linear model and also for an extreme environmental state. We show that computed loads are generally larger with the nonlinear wave modeling assumptions; this establishes the importance of using such refined nonlinear wave models in stochastic simulation of the response of offshore wind turbines.

Numerical Prototyping of Floating Offshore Wind Turbines: Virtual Operation in Real Environmental Conditions

2020 ◽  
Author(s):  
Daniel Milano ◽  
Christophe Peyrard ◽  
Matteo Capaldo
Keyword(s):  
Wind Turbines ◽  
Wind Wave ◽  
Fatigue Analysis ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Wave Direction ◽  
Offshore Wind Turbines ◽  
Floating Offshore Wind Turbines ◽  
Wave Conditions

Abstract The numerical fatigue analysis of floating offshore wind turbines (FOWTs) must account for the environmental loading over a typical design life of 25 years, and the stochastic nature of wind and waves is represented by design load cases (DLCs). In this statistical approach, combinations of wind speeds and directions are associated with different sea states, commonly defined via simplified wave spectra (Pierson-Moskowitz, JONSWAP), and their probability of occurrence is identified based on past observations. However, little is known about the difference between discretizing the wind/wave direction bins into (e.g.) 10deg bins rather than 30deg bins, and the impact it has on FOWT analyses. In addition, there is an interest in identifying the parameters that best represent real sea states (significant wave height, peak period) and wind fields (profile, turbulence) in lumped load cases. In this context, the aim of this work is to better understand the uncertainties associated to wind/wave direction bin size and to the use of metocean parameters as opposed to real wind and sea state conditions. A computational model was developed in order to couple offshore wind turbine models with realistic numerical metocean models, referred to as numerical prototype due to the highly realistic wind/wave conditions in which it operates. This method allows the virtual installation of FOWTs anywhere within a considered spatial domain (e.g. the Mediterranean Sea or the North Sea) and their behaviour to be evaluated in measured wind and modelled wave conditions. The work presented in this paper compares the long-term dynamic behaviour of a tension-leg platform (TLP) FOWT design subject to the numerical prototype and to lumped load cases with different direction bin sizes. Different approaches to representing the wind filed are also investigated, and the modelling choices that have the greatest impact on the fidelity of lumped load cases are identified. The fatigue analysis suggests that 30deg direction bins are sufficient to reliably represent long-term wind/wave conditions, while the use of a constant surface roughness length (as suggested by the IEC standards) seems to significantly overestimate the cumulated damage on the tower of the FOWT.

scholarly journals Vibration Reduction Strategy for Offshore Wind Turbines

2020 ◽  
Vol 10 (17) ◽  
pp. 6091
Author(s):  
Haoming Liu ◽  
Suxiang Yang ◽  
Wei Tian ◽  
Min Zhao ◽  
Xiaoling Yuan ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Output Power ◽  
Wind Turbines ◽  
Reference Signal ◽  
Offshore Wind ◽  
Wave Load ◽  
Offshore Wind Turbines ◽  
Pitch Control ◽  
Simulation Results ◽  
Aerodynamic Torque

The operational environment of offshore wind turbines is much more complex than that of onshore wind turbines. Facing the persistent wind and wave forces, offshore wind turbines are prone to vibration problems, which are not conducive to their long-term operation. Under this background, first, how the wave affects the vibration characteristics of offshore wind turbines is analyzed. Based on the existing wave and wave load models, we analytically show that there exist fluctuating components related to the hydrodynamic frequency in the aerodynamic load and aerodynamic torque of offshore wind turbines. Simulation results based on a GH Bladed platform further validates the analysis. Second, in order to reduce the joint impacts of the wave, wind shear and tower shadow on the wind turbine, a variable pitch control method is proposed. The integrated tower top vibration acceleration signal is superimposed on the collective pitch reference signal, then the triple frequency (3P) fluctuating component of the wind turbine output power and the azimuth angle of each blade are converted into the pitch angle adjustment signal of each blade, which is superimposed on the collective pitch signal for individual pitch control. The simulation results show that the proposed pitch control strategy can effectively smooth the fluctuation of blade root flap-wise load caused by wind and wave, and significantly reduce the fluctuation of aerodynamic torque and output power of offshore wind turbines.

Model Tests on the Long-Term Dynamic Performance of Offshore Wind Turbines Founded on Monopiles in Sand

2015 ◽  
Vol 137 (4) ◽  
Author(s):  
Zhen Guo ◽  
Luqing Yu ◽  
Lizhong Wang ◽  
S. Bhattacharya ◽  
G. Nikitas ◽  
...  
Keyword(s):  
Dynamic Response ◽  
Wind Turbines ◽  
Model Tests ◽  
Offshore Wind ◽  
Frequency Change ◽  
Test Results ◽  
Scaled Model ◽  
Structural Dynamic ◽  
Offshore Wind Turbines

The dynamic response of the supporting structure is critical for the in-service stability and safety of offshore wind turbines (OWTs). The aim of this paper is to first illustrate the complexity of environmental loads acting on an OWT and reveal the significance of its structural dynamic response for the OWT safety. Second, it is aimed to investigate the long-term performance of the OWT founded on a monopile in dense sand. Therefore, a series of well-scaled model tests have been carried out, in which an innovative balance gear system was proposed and used to apply different types of dynamic loadings on a model OWT. Test results indicated that the natural frequency of the OWT in sand would increase as the number of applied cyclic loading went up, but the increasing rate of the frequency gradually decreases with the strain accumulation of soil around the monopile. This kind of the frequency change of OWT is thought to be dependent on the way how the OWT is cyclically loaded and the shear strain level of soil in the area adjacent to the pile foundation. In this paper, all test results were plotted in a nondimensional manner in order to be scaled up to predict the consequences for prototype OWT in sandy seabed.

Sign in / Sign up

Export Citation Format

Share Document