Deformation Analysis and Reliability Assessment of the Ship Hull in Irregular Waves

2013 ◽  
Author(s):  
Pengyao Yu ◽  
Guoqing Feng ◽  
Huilong Ren ◽  
Xiaodong Zhao
Keyword(s):  
Finite Element ◽  
Wave Amplitude ◽  
Ship Hull ◽  
Irregular Waves ◽  
Relative Deformation ◽  
Linear Potential ◽  
Regular Wave ◽  
Analysis Method ◽  
Deformation Response ◽  
The Waves

When the ship navigates in the sea, the dynamic deformation of the ship hull will be induced by the waves. The relative large deformation of the ship hull induced by the waves may affect the operation of some certain equipment. In order to keep the equipment operating normally, the influence of the ship deformation should be evaluated. The method for the calculation and analysis of the ship deformation is discussed here. The wave loads of the ship in unit regular wave amplitude are calculated based on 3-D linear potential flow theory. The sea pressure and inertial force of the ship are obtained and applied to the global finite element model of the ship. Under the quasi-static assumption, the structural deformation response in unit regular wave amplitude is calculated with the use of finite element analysis. Then, the amplitude frequency response of the relative deformation between two arbitrary positions in the hull is achieved. The history of the deformation can be obtained based on the simulation of deformation response in irregular waves or the modal superposition method. With the help of spectral analysis method, the spectrum of the relative deformation between two arbitrary positions in the hull may be obtained. The statistical analysis of ship hull deformation in the short-term sea state is realized. Considering the critical value of ship deformation, the reliability analysis method is adopted to assess the ability of hull to resist the deformation.

Use of the Finite Element Analysis Method in Pedodontics

2018 ◽  
Vol 55 (4) ◽  
pp. 666-675
Author(s):  
Mihaela Tanase ◽  
Dan Florin Nitoi ◽  
Marina Melescanu Imre ◽  
Dorin Ionescu ◽  
Laura Raducu ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Structural Model ◽  
Analysis Method ◽  
Ansys Software ◽  
Concentrated Force ◽  
Element Analysis ◽  
Finite Element Analysis Method ◽  
The Finite Element Analysis ◽  
Solid Type

The purpose of this study was to determinate , using the Finite Element Analysis Method, the mechanical stress in a solid body , temporary molar restored with the self-curing GC material. The originality of our study consisted in using an accurate structural model and applying a concentrated force and a uniformly distributed pressure. Molar structure was meshed in a Solid Type 45 and the output data were obtained using the ANSYS software. The practical predictions can be made about the behavior of different restorations materials.

Linear and non-linear potential-flow calculations of free-surface waves with lift and induced drag

2000 ◽  
Vol 214 (6) ◽  
pp. 801-812
Author(s):  
C-E Janson
Keyword(s):  
Free Surface ◽  
Potential Flow ◽  
Lift Force ◽  
Radiation Condition ◽  
Linear Potential ◽  
Surface Boundary ◽  
Model Approximation ◽  
Non Linear ◽  
Lifting Surfaces ◽  
The Waves

A potential-flow panel method is used to compute the waves and the lift force from surface-piercing and submerged bodies. In particular the interaction between the waves and the lift produced close to the free surface is studied. Both linear and non-linear free-surface boundary conditions are considered. The potential-flow method is of Rankine-source type using raised source panels on the free surface and a four-point upwind operator to compute the velocity derivatives and to enforce the radiation condition. The lift force is introduced as a dipole distribution on the lifting surfaces and on the trailing wake, together with a flow tangency condition at the trailing edge of the lifting surface. Different approximations for the spanwise circulation distribution at the free surface were tested for a surface-piercing wing and it was concluded that a double-model approximation should be used for low speeds while a single-model, which allows for a vortex at the free surface, was preferred at higher speeds. The lift force and waves from three surface-piercing wings, a hydrofoil and a sailing yacht were computed and compared with measurements and good agreement was obtained.

Finite Element Analysis on Rack and Pinion of Roadheader

2013 ◽  
Vol 791-793 ◽  
pp. 718-721
Author(s):  
Man Man Xu ◽  
Yu Li ◽  
Sai Nan Xie ◽  
Qing Hua Chen
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Spur Gear ◽  
Stress And Strain ◽  
Analysis Method ◽  
Element Analysis ◽  
The Road ◽  
The Finite Element Analysis ◽  
Gear Rack ◽  
Stress And Strain Distribution

To analyse the road-header rack and pinion by using the finite element analysis software COSMOS/WORKS. Compared to the traditional analytic calculation and numerical analysis method, it is more intuitively get 28 ° pressure angle spur gear rack meshing stress and strain distribution, which can rack and pinion improvements designed to provide scientific reference.

Alternative Methodologies for Subsea Flexible Strength Analysis

2018 ◽  
Author(s):  
Anskey A. Miranda ◽  
Fred P. Turner ◽  
Nigel Barltrop
Keyword(s):  
Real World ◽  
Wave Train ◽  
Irregular Waves ◽  
Wave Crest ◽  
Strength Analysis ◽  
New Wave ◽  
Regular Wave ◽  
Wave Analysis ◽  
Sea State ◽  
Irregular Wave

This paper presents a study of the analysis methodologies used to predict the most likely response of flexibles in a subsea environment, with the aim of determining an efficient and reliable prediction methodology. The most accurate method involves simulating multiple wave realisations of a real world sea state, i.e. irregular waves, and post-processing the results to determine the most probable maximum (MPM). Due to the computationally intensive nature of this approach, however, regular wave analysis is typically used to determine flexible response. This approach considers the maximum wave within a design storm at a desired period; the choice of periods may leave room for uncertainty in the conservatism of the approach. With proper screening, regular wave analysis can be a valid yet overly conservative approach resulting in over design and additional cost. However, if screened incorrectly, there is a possibility that the choice of periods could give results that are under conservative. In addition to regular wave analysis, the paper presents two alternative methodologies to determine the most likely response, with the focus on reducing the computational resources required. The first alternative is an ‘Irregular Wave Screen’ approach in which the wave train is screened at areas of interest for waves within a user defined threshold of the maximum wave height, in addition to other user defined parameters. Only waves within these parameters are simulated to determine responses. The second alternative is the ‘New Wave’ approach, which models the most probable wave elevation around the maximum wave crest. The calculated new wave is then placed at the desired location to determine responses. The responses of the Regular, Irregular Wave Screen and New Wave methodologies are compared with the Irregular MPM approach to determine their feasibility to predict the response of flexibles in a real world irregular sea state with lower computational requirements.

scholarly journals REDUCTION OF WAVE OVERTOPPING RATE BY THE USE OF ARTIFICIAL REEFS

1988 ◽  
Vol 1 (21) ◽  
pp. 23
Author(s):  
Toru Sawaragi ◽  
Ichiro Deguchi ◽  
San-Kil Park
Keyword(s):  
Wave Breaking ◽  
Artificial Reef ◽  
Numerical Procedure ◽  
Artificial Reefs ◽  
Irregular Waves ◽  
Analysis Method ◽  
Wave Analysis ◽  
Wave Overtopping ◽  
Unidirectional Flow ◽  
Individual Wave

A wave overtopping rate from a sea dike of various toe depths is formulated based on a weir model in an unidirectional flow. To evaluated the wave overtopping rate from a seadike on an artificial reef by the weir model, a numerical procedure for predicting wave transformations including the effect of forced wave breaking on the reef is constructed. After confirming the applicability of the model through experiments with regular and irregular waves, the effect of artificial reef on wave overtopping is discussed. So-called individual wave analysis method is shown to he applicable to the wave overtopping caused by irregular waves.

scholarly journals BREAKWATER ARMOR DISPLACEMENT THRESHOLDS: A POSSIBLE CORRELATION WITH CUMULATIVE WAVE ENERGY

1984 ◽  
Vol 1 (19) ◽  
pp. 186
Author(s):  
Daniel L. Behnke ◽  
Frederic Raichlen
Keyword(s):  
Wave Energy ◽  
Wave Train ◽  
Wave Length ◽  
Simple Wave ◽  
Wave Theory ◽  
Irregular Waves ◽  
Reconstruction Technique ◽  
Regular Wave ◽  
Regular Waves ◽  
Three Dimensional Model

An extensive program of stability experiments in a highly detailed three-dimensional model has recently been completed to define a reconstruction technique for a damaged breakwater (Lillevang, Raichlen, Cox, and Behnke, 1984). Tests were conducted with both regular waves and irregular waves from various directions incident upon the breakwater. In comparison of the results of the regular wave tests to those of the irregular wave tests, a relation appeared to exist between breakwater damage and the accumulated energy to which the structure had been exposed. The energy delivered per wave is defined, as an approximation, as relating to the product of H2 and L, where H is the significant height of a train of irregular waves and L is the wave length at a selected depth, calculated according to small amplitude wave theory using a wave period corresponding to the peak energy of the spectrum. As applied in regular wave testing, H is the uniform wave height and L is that associated with the period of the simple wave train. The damage in the model due to regular waves and that caused by irregular waves has been related through the use of the cumulative wave energy contained in those waves which have an energy greater than a threshold value for the breakwater.

scholarly journals Finite Element Analysis of Foundation Pile Anchor Support System

2018 ◽  
Vol 1 (1) ◽  
Author(s):  
Zhenli Yang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Construction Projects ◽  
Analysis Method ◽  
Support Structure ◽  
Foundation Pit ◽  
Element Analysis ◽  
High Rise ◽  
Finite Element Analysis Method ◽  
Foundation Pile

With the continuous development of urban construction projects in HebeiProvince, the rise and development of high-rise buildings and undergroundengineering, the design and research of foundation pit support structure has become more and more important. The design of the foundation pit support structure directly affects the settlement and position changes of the building itself and the surrounding stratum. In this paper, the characteristics of foundation pit support are analyzed, and the related theories of finite element analysis method are introduced. Combined with the actual situation of Hebei Province, the finite element analysis method is used to simulate the construction method of foundation pile anchor support structure system. The design was analyzed and studied.

scholarly journals Evaluation of the Effects of the Chincup Appliance on the Craniofacial Structures by the Finite Element Analysis

2017 ◽  
Vol 7 ◽  
pp. 219-223
Author(s):  
Beril Demir Karamanli ◽  
Hülya Kılıçoğlu ◽  
Armagan Fatih Karamanli
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Fe Model ◽  
Analysis Method ◽  
Class Iii ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element ◽  
Clinical Changes

Aims The aim of this study is to evaluate the effects of the chincup appliance used in the treatment of Class III malocclusions, not only on the mandible or temporomandibular joint (TMJ) but also on all the craniofacial structures. Materials and Methods Chincup simulation was performed on a three-dimensional finite element (FE) model. 1000 g (500 g per side) force was applied in the direction of chin-condyle head. Nonlinear FE analysis was used as the numerical analysis method. Results By the application of chincup, stresses were distributed not only on TMJ or mandible but also on the circummaxillary sutures and other craniofacial structures. Conclusions Clinical changes obtained by chincup treatment in Class III malocclusions are not limited by only mandible. It was seen that also further structures were affected.

Sign in / Sign up

Export Citation Format

Share Document