Yaw Galloping of a TLWP Platform Under High Speed Currents by Analytical Methods and its Comparison With Experimental Results

2017 ◽  
Author(s):  
Francisco Lamas ◽  
Miguel A. M. Ramirez ◽  
Antonio Carlos Fernandes
Keyword(s):  
High Speed ◽  
Production Systems ◽  
Experimental Tests ◽  
Experimental Results ◽  
Analytical Methodology ◽  
New Approach ◽  
Laboratory Facilities ◽  
Polynomial Curve ◽  
Computational Fluid Dynamics Cfd ◽  
Cfd Analyses

Flow Induced Motions are always an important subject during both design and operational phases of an offshore platform life. These motions could significantly affect the performance of the platform, including its mooring and oil production systems. These kind of analyses are performed using basically two different approaches: experimental tests with reduced models and, more recently, with Computational Fluid Dynamics (CFD) dynamic analysis. The main objective of this work is to present a new approach, based on an analytical methodology using static CFD analyses to estimate the response on yaw motions of a Tension Leg Wellhead Platform on one of the several types of motions that can be classified as flow-induced motions, known as galloping. The first step is to review the equations that govern the yaw motions of an ocean platform when subjected to currents from different angles of attack. The yaw moment coefficients will be obtained using CFD steady-state analysis, on which the yaw moments will be calculated for several angles of attack, placed around the central angle where the analysis is being carried out. Having the force coefficients plotted against the angle values, we can adjust a polynomial curve around each analysis point in order to evaluate the amplitude of the yaw motion using a limit cycle approach. Other properties of the system which are flow-dependent, such as damping and added mass, will also be estimated using CFD. The last part of this work consists in comparing the analytical results with experimental results obtained at the LOC/COPPE-UFRJ laboratory facilities.

Pumping Loss of Shrouded Meshed Spur Gears

2020 ◽  
Vol 142 (11) ◽  
Author(s):  
Michael J. Hurrell ◽  
Jerzy T. Sawicki
Keyword(s):  
High Speed ◽  
Spur Gear ◽  
Test Facility ◽  
Spur Gears ◽  
Cfd Analysis ◽  
Total Load ◽  
New Approach ◽  
Computational Fluid Dynamics Cfd ◽  
Loss Component ◽  
Swept Volume

Abstract High speed rotorcraft transmissions are subject to load-independent power losses consisting of drag loss and pumping loss. Tightly conforming shrouds enclosing the transmission gears are often incorporated to reduce the drag component of the total load-independent losses. However, tightly conforming axial shrouds can result in an increase in the pumping loss component. Quantifying the pumping loss of shrouded gear transmissions has been the subject of many studies. This study presents a new approach for estimating pumping loss based on the concept of swept volume and examines the applicability of the approach to various shroud configurations. The drag loss and pumping loss of a shrouded spur gear pair have been determined through testing using the NASA Glenn Research Center (GRC) Gear Windage Test Facility. The results from this testing have been compared to theoretical results using the formulations presented in this study. In addition, computational fluid dynamics (CFD) analysis has been conducted for the various shroud configurations tested at NASA GRC. The results from the CFD analysis confirm the theoretical and empirical results and provide insight into the applicability of the swept volume approach for estimating pumping power loss of shrouded gear transmissions.

New Approach to Assess in Vivo Rearfoot Control of Court Footwear during Side-Stepping Moves

1997 ◽  
Vol 13 (2) ◽  
pp. 197-204 ◽  
Author(s):  
Mario A. Lafortune
Keyword(s):  
High Speed ◽  
Pressure Sensors ◽  
Experimental Results ◽  
Lateral Side ◽  
New Approach ◽  
High Speed Video ◽  
High Discrimination

Miniature pressure sensors and high-speed video were used to assess the lateral support and stability of court footwear during in vivo performance of lateral side-stepping moves. Two distinct types of court footwear construction were evaluated and were found to differ by approximately 100% and 200% in lateral support and stability, respectively. The heel control index that combined both parameters revealed differences exceeding 425%. A comparison of shoes that differed only in one construction feature produced similar trends. These overall results suggest that the combined high-speed video/pressure approach allows high discrimination of footwear rearfoot control properties during in vivo simulated playing conditions. The specific experimental results suggest that footwear designed for court sports exhibits considerable differences in foot support and stability. Furthermore, it was found that some construction features could improve these properties in court footwear.

scholarly journals Numerical and Experimental Study on Seakeeping Performance of a High-Speed Trimaran with T-foil in Head Waves

2019 ◽  
Vol 26 (3) ◽  
pp. 65-77 ◽  
Author(s):  
Ang Li ◽  
Yunbo Li
Keyword(s):  
High Speed ◽  
Experimental Tests ◽  
Longitudinal Motion ◽  
Vertical Acceleration ◽  
Large Wave ◽  
Seakeeping Performance ◽  
Head Waves ◽  
Computational Fluid Dynamics Cfd ◽  
Motion Characteristics ◽  
Cfd Method

Abstract The longitudinal motion characteristics of a slender trimaran equipped with and without a T-foil near the bow are investigated by experimental and numerical methods. Computational fluid dynamics ( CFD) method is used in this study. The seakeeping characteristics such as heave, pitch and vertical acceleration in head regular waves are analyzed in various wave conditions. Numerical simulations have been validated by comparisons with experimental tests. The influence of large wave amplitudes and size of T-foil on the longitudinal motion of trimaran are analyzed. The present systematic study demonstrates that the numerical results are in a reasonable agreement with the experimental data. The research implied that the longitudinal motion response values are greatly reduced with the use of T-foil.

scholarly journals Improving resistance properties of high-speed ships

2020 ◽  
Vol XXIII (2) ◽  
pp. 8-18
Author(s):  
Gürsel K.Turgut
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
High Speed ◽  
Carbon Emission ◽  
Container Ship ◽  
Commercial Software ◽  
Sustainable Engineering ◽  
Speed Range ◽  
Computational Fluid Dynamics Cfd ◽  
Cfd Analyses

Sustainable engineering solutions facilitate and/or force the use of energy more efficiently and, thus, reducing the carbon emission to the atmosphere. This study is related to improving resistance properties of ships, especially in the high speed range, in which they consume large amount of fuels. In this investigation, the model of the Kriso Container Ship (KCS) was taken as the basis to be studied and she was hydrodynamically analysed through the commercial software STAR-CCM+. After the successful validation of the results obtained in these computational fluid dynamics (CFD) analyses by those of the experiments of this model published in [1], the simulations carried out on the models equipped with stern flaps and a combination of stern flaps and interceptors for reducing resistance of the models, were performed in the same manner using the same software. Then the results obtained in all analyses were discussed by comparing those with the test ones.

Numerical Simulation of the Viscous Flow around High-Speed Ship Hull Considering the Free Surface

2011 ◽  
Vol 101-102 ◽  
pp. 966-969
Author(s):  
Wei Hua Hu
Keyword(s):  
Numerical Simulation ◽  
Free Surface ◽  
High Speed ◽  
Free Water ◽  
Experimental Results ◽  
Two Phase ◽  
Ship Model ◽  
Fluent Software ◽  
Computational Fluid Dynamics Cfd ◽  
Cfd Method

Over the last decade, considering the influence of the viscous free water surface, the numerical simulation of the flow around the hull is one of the focuses in ship research. Currently, the precision of numerical simulation results need to be enhanced. In this paper, Computational Fluid Dynamics (CFD) method is used, for a real high-speed ship model, to simulate the flow around the hull and to calculate the total hull resistance with FLUENT software. The Volume of Fraction (VOF) method of two-phase fluid is used to deal with the free surface tracking. The results of resistance are compared with the ship model experimental results. It is shown that the total resistance results calculated accord with the experimental results well, and the numerical method can simulate the profile of the ship wave-making.

The Effect of Strain Rate on the Material Characteristics of Nickel-Based Superalloy Inconel 718

2007 ◽  
Vol 340-341 ◽  
pp. 283-288 ◽  
Author(s):  
Jung Han Song ◽  
Hoon Huh
Keyword(s):  
Dynamic Response ◽  
High Strain Rate ◽  
Strain Rate ◽  
Turbine Blade ◽  
Inconel 718 ◽  
High Speed ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Experimental Results ◽  
Stress Wave Propagation

The dynamic response of the turbine blade materials is indispensable for analysis of erosions of turbine blades as a result of impulsive loading associated with gas flow. This paper is concerned with the dynamic material properties of the Inconel 718 alloy which is widely used in the high speed turbine blade. The dynamic response at the corresponding level of the strain rate should be acquired with an adequate experimental technique and apparatus due to the inertia effect and the stress wave propagation. In this paper, the dynamic response of the Inconel 718 at the intermediate strain rate ranged from 1/s to 400/s is obtained from the high speed tensile test and that at the high strain rate above 1000/s is obtained from the split Hopkinson pressure bar test. The effects of the strain rate on the dynamic flow stress, the strain rate sensitivity and the failure elongation are evaluated with the experimental results. Experimental results from both the quasi-static and the high strain rate up to 3000/s are interpolated in order to construct the constitutive relation that should be applied to simulate the dynamic behavior of the turbine blade made of the Inconel 718.

scholarly journals Research on aerodynamic characteristics of two-stage axial micro air turbine spindle for small parts machining

2020 ◽  
Vol 12 (12) ◽  
pp. 168781402098437
Author(s):  
Liu Jiang ◽  
Guo Zhiping ◽  
Miao Shujing ◽  
He Xiangxin ◽  
Zhu Xinyu
Keyword(s):  
High Speed ◽  
Aerodynamic Characteristics ◽  
Maximum Efficiency ◽  
Two Stage ◽  
Output Torque ◽  
Air Turbine ◽  
Solid Foundation ◽  
Computational Fluid Dynamics Cfd ◽  
Micro Machine ◽  
Small Parts

In order to meet the requirements of output torque, efficiency and compact shape of micro-spindles for small parts machining, a two-stage axial micro air turbine spindle with an axial inlet and outlet is proposed. Based on the k-ω turbulence model of SST, the flow field and operation characteristics of the two-stage axial micro air turbine spindle were studied using computational fluid dynamics (CFD) combined with an experimental study. We obtained the air turbine spindle under different working conditions of the loss and torque characteristics. When the inlet pressure was 300 KPa, the output speed of the two-stage turbine was 100,000 rpm, 9% higher than that of a single-stage turbine output torque. The total torque reached 6.39 N·mm, and the maximum efficiency of the turbine and the spindle were 42.2% and 32.3%, respectively. Through the research on the innovative structure of the two-stage axial micro air turbine spindle, the overall performance of the principle prototype has been significantly improved and the problems of insufficient output torque and low working efficiency in high-speed micro-machining can be solved practically, which laid a solid foundation for improving the machining efficiency of small parts and reducing the size of micro machine tool.

scholarly journals A New Approach of Soft Joint Based on a Cable-Driven Parallel Mechanism for Robotic Applications

Mathematics ◽  
2021 ◽  
Vol 9 (13) ◽  
pp. 1468
Author(s):  
Luis Nagua ◽  
Carlos Relaño ◽  
Concepción A. Monje ◽  
Carlos Balaguer
Keyword(s):  
Parallel Mechanism ◽  
Degrees Of Freedom ◽  
Kinematic Model ◽  
Experimental Tests ◽  
Humanoid Robots ◽  
Inverse Kinematic ◽  
Element Analysis ◽  
New Approach ◽  
Flexible Polymer ◽  
The Mathematical Model

A soft joint has been designed and modeled to perform as a robotic joint with 2 Degrees of Freedom (DOF) (inclination and orientation). The joint actuation is based on a Cable-Driven Parallel Mechanism (CDPM). To study its performance in more detail, a test platform has been developed using components that can be manufactured in a 3D printer using a flexible polymer. The mathematical model of the kinematics of the soft joint is developed, which includes a blocking mechanism and the morphology workspace. The model is validated using Finite Element Analysis (FEA) (CAD software). Experimental tests are performed to validate the inverse kinematic model and to show the potential use of the prototype in robotic platforms such as manipulators and humanoid robots.

scholarly journals Additively Manufactured Parts Made of a Polymer Material Used for the Experimental Verification of a Component of a High-Speed Machine with an Optimised Geometry—Preliminary Research

Polymers ◽  
2020 ◽  
Vol 13 (1) ◽  
pp. 137
Author(s):  
Artur Andrearczyk ◽  
Bartlomiej Konieczny ◽  
Jerzy Sokołowski
Keyword(s):  
Polymer Material ◽  
High Speed ◽  
Numerical Models ◽  
Flow Analysis ◽  
Experimental Tests ◽  
Strength Analysis ◽  
Compressor Wheel ◽  
Operational Characteristics ◽  
3D Printed ◽  
Novel Method

This paper describes a novel method for the experimental validation of numerically optimised turbomachinery components. In the field of additive manufacturing, numerical models still need to be improved, especially with the experimental data. The paper presents the operational characteristics of a compressor wheel, measured during experimental research. The validation process included conducting a computational flow analysis and experimental tests of two compressor wheels: The aluminium wheel and the 3D printed wheel (made of a polymer material). The chosen manufacturing technology and the results obtained made it possible to determine the speed range in which the operation of the tested machine is stable. In addition, dynamic destructive tests were performed on the polymer disc and their results were compared with the results of the strength analysis. The tests were carried out at high rotational speeds (up to 120,000 rpm). The results of the research described above have proven the utility of this technology in the research and development of high-speed turbomachines operating at speeds up to 90,000 rpm. The research results obtained show that the technology used is suitable for multi-variant optimization of the tested machine part. This work has also contributed to the further development of numerical models.

Sign in / Sign up

Export Citation Format

Share Document