Study on Effects of Compressor Inlet Air Cooling on GTCC System Performance Under Different Environmental Conditions

2020 ◽  
Author(s):  
Duan Liqiang ◽  
Guo Yaofei ◽  
Pan Pan ◽  
Li Yongxia
Keyword(s):  
Relative Humidity ◽  
Ambient Temperature ◽  
Gas Turbine ◽  
Output Power ◽  
Environmental Conditions ◽  
System Performance ◽  
Combined Cycle ◽  
Air Cooling ◽  
Compressor Inlet ◽  
Cooling Technology

Abstract The environmental conditions (air temperature and relative humidity) have a great impact on the power and efficiency of gas turbine combined cycle (GTCC) system. Using the intake air cooling technology can greatly improve the performance of GTCC system. On the base of the PG9351FA gas turbine combined cycle system, this article builds the models of both the GTCC system and a typical lithium bromide absorption refrigeration system using Aspen Plus software. The effects of compressor inlet air cooling with different environmental conditions on the GTCC system performance are studied. The research results show that using the inlet air cooling technology can obviously increase the output powers of both the gas turbine and the combined cycle power. When the ambient humidity is low, the efficiency of GTCC changes gently; while the ambient humidity is high, the GTCC system efficiency will decline substantially when water in the air is condensed and removed with the progress of cooling process. At the same ambient temperature, when the relative humidity of the environment is equal to 20%, the gas turbine output power is increased by 35.64 MW, with an increase of 16.32%, and the combined cycle output power is increased by 39.57 MW, with an increase of 11.34%. At an ambient temperature of 35°C, for every 2.5 °C drop in the compressor inlet air, the thermal efficiency of the gas turbine increases by 0.189% compared to before cooling.

Effect of the Environmental Conditions of Tropical Climates on the Performance Parameters of a Gas Turbine Power Generation Plant

2020 ◽  
Author(s):  
J. Fajardo ◽  
D. Barreto ◽  
T. Castro ◽  
I. Baldiris
Keyword(s):  
Power Plant ◽  
Relative Humidity ◽  
Gas Turbine ◽  
Output Power ◽  
High Temperatures ◽  
Environmental Conditions ◽  
Thermal Efficiency ◽  
Specific Work ◽  
Atmospheric Conditions ◽  
Compressor Inlet

Abstract It is known that high temperatures adversely affect the performance of gas turbines, but the effect of the combination of atmospheric conditions (temperature and relative humidity -RH-) on the operation of this type of system is unknown. In this work the effects of atmospheric conditions on the energy and exergy indicators of a power plant with gas turbine were studied. The indicators studied were the mass flow, the specific work consumed by the compressor, specific work produced by the turbine, the combustion gas temperature, the NO concentration, the net output power, the thermal efficiency, the heat rate, the specific consumption of fuel, the destruction of exergy and exergy efficiency. Among the results, it is noted that for each degree celsius that reduces the temperature of the air at the compressor inlet at constant relative humidity on average, the mass flow of dry air increases by 0.27 kg/s, the specific work consumed by the compressors decreases by 0.45%, the output power increases by 1.17% and the thermal efficiency increases by 0.8%, the exergy destruction increases by 0.72% and the exergy efficiency increases by 0.81%. In addition, humidity changes relative to high temperatures are detected more significantly than at low temperatures. The power plant studied is installed in Cartagena, Colombia and since it is not operating in the design environmental conditions (15 °C and 60% relative humidity) it experiences a loss of output power of 6140 kW and a drop in thermal efficiency of 5.12 %. These results allow considering the implementation of air cooling technologies at the compressor inlet to compensate for the loss of power at atmospheric air conditions.

Performance Evaluation of Evaporative Compressor Inlet Air Cooling System in a Gas Turbine-Based Cogeneration Plant

2012 ◽  
Author(s):  
Farshid Zabihian ◽  
Alan S. Fung ◽  
Fabio Schuler
Keyword(s):  
Power Plant ◽  
Ambient Temperature ◽  
Gas Turbine ◽  
Output Power ◽  
Cooling System ◽  
Air Cooling ◽  
Cogeneration Plant ◽  
Cooling Systems ◽  
Compressor Inlet ◽  
Air Cooling System

Gas turbine-based power plants are very sensitive to ambient conditions and their output power and efficiency can be decreased significantly with increase in the ambient temperature. Various compressor inlet air cooling systems have been proposed and utilized to reduce inlet air temperature to the system, including evaporative systems e.g. media and fogging, and mechanical cooling systems. In this work, different techniques for compressor inlet air cooling are briefly reviewed. Then, the fogging system employed in the Whitby cogeneration power plant is explained with particular attention to the location of the system installation. A model of the gas turbine-based cogeneration plant is also developed to simulate the Whitby cogeneration power plant. The effects of fogging compressor inlet air cooling system on the performance of the plant are investigated. The results indicate that at an ambient temperature of 30°C and relative humidity of 40% the inlet cooling of as high as 8.4°C is possible which can increase output power to more than 50 MW. Also, it is found that the model can predict the gas turbine exhaust temperature and the plant’s power production with the error level of lower than 0.5% and 3%, respectively.

Comparative Analysis of Different Inlet Air Cooling Technologies Including Solar Energy to Boost Gas Turbine Combined Cycles in Hot Regions

2018 ◽  
Vol 140 (11) ◽  
Author(s):  
Ahmed Abdel Rahman ◽  
Esmail M. A. Mokheimer
Keyword(s):  
Comparative Analysis ◽  
Gas Turbine ◽  
Output Power ◽  
Power Output ◽  
Combined Cycle ◽  
Air Cooling ◽  
Absorption Chiller ◽  
Absorption Chillers ◽  
Combined Cycles ◽  
Net Power Output

Cooling the air before entering the compressor of a gas turbine of combined cycle power plants is an effective method to boost the output power of the combined cycles in hot regions. This paper presents a comparative analysis for the effect of different air cooling technologies on increasing the output power of a combined cycle. It also presents a novel system of cooling the gas turbine inlet air using a solar-assisted absorption chiller. The effect of ambient air temperature and relative humidity on the output power is investigated and reported. The study revealed that at the design hour under the hot weather conditions, the total net power output of the plant drops from 268 MW to 226 MW at 48 °C (15.5% drop). The increase in the power output using fogging and evaporative cooling is less than that obtained with chillers since their ability to cool down the air is limited by the wet-bulb temperature. Integrating conventional and solar-assisted absorption chillers increased the net power output of the combined cycle by about 35 MW and 38 MW, respectively. Average and hourly performance during typical days have been conducted and presented. The plants without air inlet cooling system show higher carbon emissions (0.73 kg CO2/kWh) compared to the plant integrated with conventional and solar-assisted absorption chillers (0.509 kg CO2/kWh) and (0.508 kg CO2/kWh), respectively. Also, integrating a conventional absorption chiller shows the lowest capital cost and levelized electricity cost (LEC).

scholarly journals Gas Turbine Uprating Programme Development and Testing of the GT11NM

1998 ◽  
Author(s):  
Christoph Schneider ◽  
Vladimir Navrotsky ◽  
Prith Harasgama
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Development Program ◽  
Combined Cycle ◽  
Economic Life ◽  
Air Cooling ◽  
Performance Improvements ◽  
Cooling Technology ◽  
Improved Performance

ABB has approximately 200 GT11N and GT11D type gas turbines currently operating in simple cycle and combined cycle power plants. Most of these machines are fairly mature with many approaching the end of their economic life. In order that the power producer may continue to operate a fleet with improved performance, Advanced Air Cooling Technology and Advanced Turbine Aerodynamics have been utilized to uprate these engines with the implementation of a completely new turbine module. The objective of the uprating program was to implement the advanced aero/cooling technology into a complete new turbine module with: • Improved power output for the gas turbine • Increase the GT cycle efficiency • Maintain or improve the gas turbine RAM (Reliability, Availability & Maintainability) • Reduce the Cost of Electricity • Maintain or reduce the emissions of the gas turbine The GT11NM gas turbine has been developed based on the GT11N which has been in operation since 1987 and Midland Cogeneration Venture (MCV-Midland, Michigan) was chosen to demonstrate the uprated GT11NM. The upate/retrofit of the GT11N engine was conducted in May/June 1997 and the resulting gas turbine - GT11NM has met and exceeded the performance goals set at the onset of the development program. The next sections detail the main changes to the turbine and the resulting performance improvements as established with the demonstration at Midland, Michigan.

Development of Air Cooled Combustor for Mitsubishi G Class Gas Turbine

2010 ◽  
Author(s):  
Keizo Tsukagoshi ◽  
Hisato Arimura ◽  
Katsunori Tanaka ◽  
Koichi Nishida ◽  
Testu Konishi ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Air Cooling ◽  
Turbine Inlet Temperature ◽  
Steam Cooling ◽  
Cooling Technology ◽  
Verification Test

Mitsubishi Heavy Industries (MHI) pioneered the introduction of steam cooling technology for gas turbines with the introduction of the M501G in 1997. To date, 62 Mitsubishi G units have been sold making this series the largest steam cooled fleet in the market. The turbine inlet temperature (TIT) for this gas turbine is 1500 deg. C. The original M501G has been upgraded for air cooling applications. This upgraded version is called as M501GAC (G Air Cooled). Several Dry Low NOx (DLN) and cooling technologies from existing F and G series were applied to the upgraded M501GAC. The new GAC combustor was installed in the in-house verification Combined Cycle Power Plant, called T-Point, and verification tests of the combustor were conducted from November 2008. The air cooled M501GAC combustor demonstrated less than 15ppm NOx operation, stable combustor dynamics at all load levels, and high combustor ignition reliability making it suitable for daily start and stop operation at T-Point. Long term verification test is currently under way.

Development of Air Cooled Combustor for Mitsubishi G Class Gas Turbine

2011 ◽  
Author(s):  
Keizo Tsukagoshi ◽  
Shinji Akamatsu ◽  
Kenji Sato ◽  
Katsunori Tanaka ◽  
Hiroaki Kishida ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Air Cooling ◽  
Turbine Inlet Temperature ◽  
Steam Cooling ◽  
Cooling Technology ◽  
Verification Test

Mitsubishi Heavy Industries (MHI) pioneered the introduction of steam cooling technology for gas turbines with the introduction of the M501G in 1997. To date, 71 Mitsubishi G units have been sold making this series the largest steam cooled fleet in the market. The turbine inlet temperature (TIT) for this gas turbine is 1500 deg. C. The original M501G has been upgraded for air cooling applications. This upgraded version is called as M501GAC (G Air Cooled). The latest Dry Low NOx (DLN) and cooling technologies from existing F and G series were applied to the upgraded M501GAC. The new GAC combustor was installed in the in-house verification Combined Cycle Power Plant, called T-Point, and verification tests of the combustor were conducted from November 2008. The air cooled M501GAC combustor demonstrated less than 15ppm NOx operation, stable combustor dynamics at all load levels, and high combustor ignition reliability making it suitable for daily start and stop operation at T-Point. Also, oil firing capabilities was tested in May, 2010. Long term verification test is completed in fall 2010.

Gas Turbine-Based Combined Cycle Power Plant Modeling and Effects of Ambient Temperature

2013 ◽  
Author(s):  
Paul Shaw ◽  
Farshid Zabihian ◽  
Alan S. Fung
Keyword(s):  
Power Plant ◽  
Ambient Temperature ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Cooling System ◽  
Combined Cycle ◽  
Air Cooling ◽  
Combined Cycle Power Plant ◽  
Ambient Temperatures ◽  
Air Cooling System

This paper presents results of the combined cycle power plant (CCPP) modeling when the ambient temperature is varying. The model of the CCPP was developed using a gas turbine and a heat recovery steam generator (HRSG) models that had been already developed and validated. The model of the components was developed based on an actual existing power plant and then the operational data of the power plant was used to validate the model. The results of running the model for various ambient temperatures demonstrated that the performance of the gas turbine part of the cycle was heavily affected by the changes in the ambient temperature, particularly the output power of the gas turbines. However, the performance of the steam cycle was almost untouched by the changes of ambient temperature. This suggests that operation of the CCPP is more stable than stand-alone gas turbine in hot summer days especially if the cycle is not equipped with an inlet air cooling system.

Sign in / Sign up

Export Citation Format

Share Document